Wheezy ran great on E02 for two weeks, now no go, EHCI time out on boot February 08, 2013 08:30AM |
Registered: 12 years ago Posts: 19 |
U-Boot 2011.12 (Feb 20 2012 - 21:21:59) Pogoplug E02 arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 4 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000008000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 91 MiB UBI: number of good PEBs: 728 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 717 UBI: total number of reserved PEBs: 11 UBI: number of PEBs reserved for bad PEB handling: 7 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1 bytes read Found bootable drive on usb 0:1 Loading file "/boot/uImage" from usb device 0:1 (usbda1) EHCI timed out on TD - token=0x800d8d80 EHCI timed out on TD - token=0x800d8d80 EHCI timed out on TD - token=0x800d8d80 ** ext2fs_devread read error - block ** Unable to read "/boot/uImage" from usb 0:1 ** Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) EHCI timed out on TD - token=0x800d8d80 ** ext2fs_devread read error - block ** Unable to read "/boot/uInitrd" from usb 0:1 ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.2.0-4-kirkwood Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1606376 Bytes = 1.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! stopping USB.. NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.3.2-kirkwide Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3627768 Bytes = 3.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...
rescue:~# e2fsck -n -f -v /dev/sda1 e2fsck 1.41.12 (17-May-2010) Pass 1: Checking inodes, blocks, and sizes Pass 2: Checking directory structure Pass 3: Checking directory connectivity Pass 4: Checking reference counts Pass 5: Checking group summary information 18491 inodes used (4.09%) 157 non-contiguous files (0.8%) 22 non-contiguous directories (0.1%) # of inodes with ind/dind/tind blocks: 1134/12/0 173281 blocks used (9.59%) 0 bad blocks 1 large file 14464 regular files 2098 directories 12 character device files 25 block device files 1 fifo 12 links 1882 symbolic links (1818 fast symbolic links) 0 sockets -------- 18494 files
Re: Wheezy ran great on E02 for two weeks, now no go, EHCI time out on boot February 08, 2013 02:19PM |
Registered: 12 years ago Posts: 19 |
rescue:~# printenv HISTFILESIZE=1000 INPUTRC=/etc/inputrc SSH_CLIENT=10.0.1.51 53953 22 MAIL=/var/mail/root USER=root HOSTNAME=rescue HOME=/root SSH_TTY=/dev/pts/0 PAGER=/bin/more PS1=\h:\w\# LOGNAME=root TERM=xterm-color PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin DMALLOC_OPTIONS=debug=0x34f47d83,inter=100,log=logfile HISTSIZE=1000 LS_COLORS=no=00:fi=00:di=01;34:ln=01;36:pi=40;33:so=01;35:do=01;35:bd=40;33;01:cd=40;33;01:or=40;31;01:ex=01;32:*.tar=01;31:*.tgz=01;31:*.arj=01;31:*.taz=01;31:*.lzh=01;31:*.zip=01;31:*.z=01;31:*.Z=01;31:*.gz=01;31:*.bz2=01;31:*.deb=01;31:*.rpm=01;31:*.jar=01;31:*.jpg=01;35:*.jpeg=01;35:*.png=01;35:*.gif=01;35:*.bmp=01;35:*.pbm=01;35:*.pgm=01;35:*.ppm=01;35:*.tga=01;35:*.xbm=01;35:*.xpm=01;35:*.tif=01;35:*.tiff=01;35:*.mpg=01;35:*.mpeg=01;35:*.avi=01;35:*.fli=01;35:*.gl=01;35:*.dl=01;35:*.xcf=01;35:*.xwd=01;35: SHELL=/bin/sh PWD=/root SSH_CONNECTION=10.0.1.51 53953 10.0.1.10 22 EDITOR=/bin/vi
rescue:~# fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ethaddr=00:25:31:04:AA:18 arcNumber=3542 serverip=10.0.1.51 ipaddr=10.0.1.10 if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000 bootcmd_pogo=run bootcmd_rescue rescue_installed=1
Re: Wheezy ran great on E02 for two weeks, now no go, EHCI time out on boot February 08, 2013 04:51PM |
Admin Registered: 14 years ago Posts: 19,423 |
fw_setenv usb_init 'usb stop; usb start; run usb_scan'
Re: Wheezy ran great on E02 for two weeks, now no go, EHCI time out on boot February 10, 2013 10:10PM |
Registered: 12 years ago Posts: 19 |
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 4 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000008000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 91 MiB UBI: number of good PEBs: 728 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 717 UBI: total number of reserved PEBs: 11 UBI: number of PEBs reserved for bad PEB handling: 7 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! stopping USB.. (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 4 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1 bytes read Found bootable drive on usb 0:1 Loading file "/boot/uImage" from usb device 0:1 (usbda1) EHCI timed out on TD - token=0x800d8d80 ** ext2fs_devread read error - block ** Unable to read "/boot/uImage" from usb 0:1 ** Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) EHCI timed out on TD - token=0x800d8d80 EHCI timed out on TD - token=0x800d8d80 ** ext2fs_devread read error - block ** Unable to read "/boot/uInitrd" from usb 0:1 ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.2.0-4-kirkwood Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1606376 Bytes = 1.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! stopping USB.. NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.3.2-kirkwide Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3627768 Bytes = 3.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...
Re: Wheezy ran great on E02 for two weeks, now no go, EHCI time out on boot February 11, 2013 01:32AM |
Admin Registered: 14 years ago Posts: 19,423 |
Re: Wheezy ran great on E02 for two weeks, now no go, EHCI time out on boot February 11, 2013 06:20AM |
Registered: 12 years ago Posts: 19 |