Re: Dockstar Please check your kernel config and/or bootloader.
December 31, 2021 09:55AM
Re: Dockstar Please check your kernel config and/or bootloader.
December 31, 2021 03:44PM
droidbox,

The Dockstar has the standard JTAG interface. Meaning you can buy the regular JTAG header and solder it in. And use the instruction in the Wiki for the Pogo E02.

https://forum.doozan.com/read.php?2,23630

Quote

Unbricking with Serial Console & JTAG console

How to unbrick your box using serial console with kwboot
Repair Pogo E02 with Raspberry PI (JTAG) and OpenOCD

You also need to use the values from Dockstar kwbimage.cfg (compare those with ones used for the Pogo E02 in the tutorial). The only difference should be the RAM size.

https://github.com/mibodhi/u-boot-kirkwood/blob/2017.07-kirkwood-tld-1/board/Seagate/dockstar/kwbimage.cfg

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Dockstar Please check your kernel config and/or bootloader.
December 31, 2021 03:47PM
You can also see rudiswiki for a quite good instruction for the Dockstar:

https://www.rudiswiki.de/wiki9/DockStarJTAG

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Dockstar Please check your kernel config and/or bootloader.
January 01, 2022 09:32AM
I found these guides to use the wrong ECC algorithm, it kinda works but you won't be able to read the nand from uboot. That's why I made another cfg file.
Btw, the USBasp has few jtag firmwares, but I don't know the actual functionality and if OpenOCD supports them.
Re: Dockstar Please check your kernel config and/or bootloader.
January 01, 2022 09:36AM
I will give this howto next week a change
https://forum.doozan.com/read.php?3,21789
I reported here ;-)
Re: Dockstar Please check your kernel config and/or bootloader.
January 01, 2022 03:26PM
@David,

> That's why I made another cfg file.

Pardon me! I forgot that part in your writeups, a long thread :)

https://forum.doozan.com/read.php?2,127079,127629#msg-127629

@droidbox,

You can use either the Pogo E02 instruction or David's instruction. But do use the dockstar.cfg in davidalfa's post.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Dockstar Please check your kernel config and/or bootloader.
April 29, 2022 05:56PM
droidbox Wrote:
-------------------------------------------------------
> bodhi, it rocks perfect. Now I can boot into the
> Alpine Linux. Great.
>
> One more question ;-)
>
> How can I disable this message at the boot?
>
1 Storage Device(s) found
> Unknown command 'ide' - try 'help'
> Unknown command 'mmc' - try 'help'
> 
> Partition Map for USB device 0  --   Partition
> Type: DOS
> 
> Part    Start Sector    Num Sectors     UUID      
>      Type
>   1     2048            31250432       
> 1d48cb6e-01     83
> 
> ## Unknown partition table type 0
> 
> ## Unknown partition table type 0
> 
> ## Unknown partition table type 0
> 
> ## Unknown partition table type 0
> 
> ## Unknown partition table type 0
> 
> ## Unknown partition table type 0
> loading envs from usb 0 ...
> 2774 bytes read in 984 ms (2 KiB/s)
> Unknown command 'ide' - try 'help'
> Unknown command 'mmc' - try 'help'
> importing envs ...
> running scan_disk ...
> Scan device usb

Can you share on how to put alpine linux on?
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: