OLD POGO E02 update to debian
July 15, 2022 06:55AM
Hello everyone, I have an old Pogo E02 that was running Arch linux arm.
I connected to serial console and found Arch linux arm uboot installed:

PogoE02> ver

U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02
gcc (GCC) 4.8.2 20131219 (prerelease)
GNU ld (GNU Binutils) 2.24

U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

no USB devices available

no USB devices available

no USB devices available

no USB devices available
This is the output of printenv
PogoE02> printenv
baudrate=115200
bootcmd=usb start; setenv letter 9;for type in usb; do for disk in 0 1 2 3; do if ${type} part ${disk};then setexpr letter $letter + 1;run load;fi;done;done;
bootdelay=3
bootm=echo Booting from ${disk} ...; run setargs; bootm ${loadaddr};
bootz=echo Booting from ${disk} ...; run setargs; bootz ${loadaddr} - ${fdt_addr};
console=ttyS0
ethact=egiga0
ethaddr=00:25:31:00:66:7E
fdt_addr=0x800000
fdt_file=/boot/dtbs/kirkwood-pogo_e02.dtb
importbootenv=echo Importing environment (uEnv.txt)...; env import -t $loadaddr $filesize
letter=9
load=echo Attempting to boot from ${type} ${disk}:1...;if run loadbootenv; then run importbootenv;fi;echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;echo Running default loadzimage ...;if run loadzimage; then run loadfdt;run bootz;fi;echo Running default loaduimage ...;if run loaduimage; then run bootm;fi;
loadaddr=0x810000
loadbootenv=load ${type} ${disk}:1 ${loadaddr} /boot/uEnv.txt
loadfdt=load ${type} ${disk}:1 ${fdt_addr} ${fdt_file}
loaduimage=load ${type} ${disk}:1 ${loadaddr} ${uimage}
loadzimage=load ${type} ${disk}:1 ${loadaddr} ${zimage}
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),-(rootfs)
setargs=setenv bootargs console=${console},${baudrate} ${optargs} root=/dev/sd${letter}1 rw rootwait ${mtdparts}
uimage=/boot/uImage
zimage=/boot/zImage

Environment size: 1434/131068 bytes


Is it possible to install Debian with this uboot? I imagine the best scenario would be to update the latest uboot and install Debian,
could you tell me which steps to follow, please?
Thank you in advance.
Marco



Edited 8 time(s). Last edit at 07/15/2022 07:24AM by ueghio.
Re: OLD POGO E02 update to debian
July 15, 2022 11:48AM
I think this is what you are looking for:

Arch to Debian
Re: OLD POGO E02 update to debian
July 16, 2022 06:02AM
Thank you Bluzfanmr1, unfortunately i have some problem to figure out what version of rootfs to choose and which steps i Need to install It on my USB drive. Can you please provide me a step to step explanation? Is my actual uboot compatible with the last image of rootfs? As you can see i miss some knowhow.
I have 3 pogo e02 and i succesfully ran ALArm, but i found only One procedure to install It on, and for a newbie like me It was fairly simple following step by step the procedure. Debian is quite difficult to install for me.
Thank you in advance for your patience.
Kind regards,
Marco



Edited 1 time(s). Last edit at 07/16/2022 06:11AM by ueghio.
Re: OLD POGO E02 update to debian
July 16, 2022 03:09PM
Marco,

You can use the latest rootfs: Debian-5.13.6-kirkwood-tld-1-rootfs-bodhi.tar.bz2.

1. Scroll down to section

Quote

Updated 26 Sept 2021:

Basic Debian bullseye Kirkwood rootfs for most Kirwood plugs:

While in Arch Linux ARM, create the rootfs on another USB thumbdrive, following the instruction from Step 1 to 5.

2. To prepare the uEnv.txt to boot Debian, follow the instruction in this post:

https://forum.doozan.com/read.php?3,23727,23727#msg-23727

3. Shutdown the box, and unplug the Arch Linux ARM USB drive, power up. Watch serial console to see if it boots all the way to the Debian login prompt.

Please post the entire serial boot log if you see any problem, or it cannot boot to Debian.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 07/16/2022 03:11PM by bodhi.
Re: OLD POGO E02 update to debian
July 19, 2022 03:17PM
Hi bodhi and thank you for your detailed explanation.
This is the bootlog
U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            60536832        8118311d-01     83
Attempting to boot from usb 0:1...
745 bytes read in 290 ms (2 KiB/s)
Importing environment (uEnv.txt)...
Checking if uenvcmd is set ...
Running default loadzimage ...
** File not found /boot/zImage **
Running default loaduimage ...
5446002 bytes read in 436 ms (11.9 MiB/s)
Running loadfdt ...
10114 bytes read in 1323 ms (6.8 KiB/s)
Running loaduinitrd ...
9671091 bytes read in 483 ms (19.1 MiB/s)
Running loaduimage ...
5446002 bytes read in 435 ms (11.9 MiB/s)
Booting from usb 0:1 ...
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-5.13.6-kirkwood-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5445938 Bytes = 5.2 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-5.13.6-kirkwood-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9671027 Bytes = 9.2 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
   Booting using the fdt blob at 0x1c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 0f1e9000, end 0fb22173 ... OK
   Loading Device Tree to 0f1e3000, end 0f1e8781 ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021
[    0.000000][    T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000][    T0] CPU: VIVT data cache, VIVT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: CloudEngines Pogoplug E02
[    0.000000][    T0] printk: bootconsole [earlycon0] enabled
[    0.000000][    T0] Memory policy: Data cache writeback
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000][    T0] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10
[    0.000000][    T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 240508K/262144K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 21636K reserved, 0K cma-reserved)
[    0.000000][    T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0
[    0.000000][    T0] trace event string verifier disabled
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0]  Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0]  Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000002][    T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.008609][    T0] Switching to timer-based delay loop, resolution 5ns
[    0.016122][    T0] Console: colour dummy device 80x30
[    0.021394][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[    0.032735][    T0] pid_max: default: 32768 minimum: 301
[    0.038482][    T0] LSM: Security Framework initializing
[    0.044040][    T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.052163][    T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.062142][    T0] CPU: Testing write buffer coherency: ok
[    0.070260][    T1] Setting up static identity map for 0x100000 - 0x100058
[    0.077461][    T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[    0.083728][    T1] rcu: Hierarchical SRCU implementation.
[    0.090746][    T1] devtmpfs: initialized
[    0.100462][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.111166][    T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.156151][    T1] prandom32: self test passed (less than 6 bits correlated)
[    0.163386][    T1] prandom: seed boundary self test passed
[    0.173225][    T1] prandom: 100 self tests passed
[    0.178056][    T1] pinctrl core: initialized pinctrl subsystem
[    0.185696][    T1] NET: Registered protocol family 16
[    0.191757][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.200398][    T1] audit: initializing netlink subsys (disabled)
[    0.207947][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.208338][   T16] audit: type=2000 audit(0.190:1): state=initialized audit_enabled=0 res=1
[    0.223786][    T1] cpuidle: using governor ladder
[    0.228762][    T1] cpuidle: using governor menu
[    0.233902][    T1] Feroceon L2: Enabling L2
[    0.238236][    T1] Feroceon L2: Cache support initialised.
[    0.252349][    T1] No ATAGs?
[    2.568616][    C0] random: fast init done
[    5.146589][   T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher
[    5.180168][   T59] wait_for_initramfs() called before rootfs_initcalls
[    5.378888][    T1] raid6: int32x8  gen()   108 MB/s
[    5.548708][    T1] raid6: int32x8  xor()    68 MB/s
[    5.718719][    T1] raid6: int32x4  gen()   109 MB/s
[    5.888763][    T1] raid6: int32x4  xor()    71 MB/s
[    6.058710][    T1] raid6: int32x2  gen()   139 MB/s
[    6.228695][    T1] raid6: int32x2  xor()    85 MB/s
[    6.398817][    T1] raid6: int32x1  gen()    97 MB/s
[    6.568634][    T1] raid6: int32x1  xor()    60 MB/s
[    6.573624][    T1] raid6: using algorithm int32x2 gen() 139 MB/s
[    6.579760][    T1] raid6: .... xor() 85 MB/s, rmw enabled
[    6.585274][    T1] raid6: using intx1 recovery algorithm
[    6.590997][    T1] vgaarb: loaded
[    6.594995][    T1] SCSI subsystem initialized
[    6.600040][    T1] usbcore: registered new interface driver usbfs
[    6.606312][    T1] usbcore: registered new interface driver hub
[    6.612448][    T1] usbcore: registered new device driver usb
[    6.618431][    T1] pps_core: LinuxPPS API ver. 1 registered
[    6.624142][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    6.634058][    T1] PTP clock support registered
[    6.640618][    T1] clocksource: Switched to clocksource orion_clocksource
[    6.751327][    T1] VFS: Disk quotas dquot_6.6.0
[    6.756066][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    6.791923][    T1] NET: Registered protocol family 2
[    6.797170][    T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    6.821715][    T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    6.840675][    T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    6.849111][    T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    6.880696][    T1] TCP: Hash tables configured (established 2048 bind 2048)
[    6.888054][    T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[    6.910728][    T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    6.918014][    T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    6.940902][    T1] NET: Registered protocol family 1
[    6.950942][    T1] RPC: Registered named UNIX socket transport module.
[    6.957601][    T1] RPC: Registered udp transport module.
[    6.970640][    T1] RPC: Registered tcp transport module.
[    6.976070][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    7.000642][    T1] PCI: CLS 0 bytes, default 32
[    7.005594][    T1] NetWinder Floating Point Emulator V0.97 (double precision)
[    8.391962][    T1] Initialise system trusted keyrings
[    8.397190][    T1] Key type blacklist registered
[    8.402251][    T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    8.409547][    T1] zbud: loaded
[    8.414388][    T1] NFS: Registering the id_resolver key type
[    8.420194][    T1] Key type id_resolver registered
[    8.425176][    T1] Key type id_legacy registered
[    8.429949][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    8.437418][    T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    8.445602][    T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    8.452991][    T1] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    8.461335][    T1] fuse: init (API version 7.34)
[    8.466489][    T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[    8.473908][    T1] orangefs_init: module version upstream loaded
[    8.480035][    T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[    8.590745][    T1] xor: measuring software checksum speed
[    8.605190][    T1]    arm4regs        :  1113 MB/sec
[    8.625086][    T1]    8regs           :   667 MB/sec
[    8.640444][    T1]    32regs          :   961 MB/sec
[    8.645552][    T1] xor: using function: arm4regs (1113 MB/sec)
[    8.651554][    T1] async_tx: api initialized (async)
[    8.656640][    T1] Key type asymmetric registered
[    8.661494][    T1] Asymmetric key parser 'x509' registered
[    8.667147][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    8.675403][    T1] io scheduler bfq registered
[    8.879532][    T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    8.889912][    T1] mv_xor f1060800.xor: Marvell shared XOR driver
[    8.951758][    T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    8.962515][    T1] mv_xor f1060900.xor: Marvell shared XOR driver
[    9.031722][    T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    9.042728][    T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    9.051271][    T1] printk: console [ttyS0] disabled
[    9.056348][    T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[    9.066191][    T1] printk: console [ttyS0] enabled
[    9.066191][    T1] printk: console [ttyS0] enabled
[    9.076047][    T1] printk: bootconsole [earlycon0] disabled
[    9.076047][    T1] printk: bootconsole [earlycon0] disabled
[    9.096622][    T1] loop: module loaded
[    9.101533][    T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    9.108634][    T1] nand: Hynix NAND 128MiB 3,3V 8-bit
[    9.113833][    T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    9.122474][    T1] Scanning device for bad blocks
[    9.247116][    T1] 4 fixed-partitions partitions found on MTD device orion_nand
[    9.254576][    T1] Creating 4 MTD partitions on "orion_nand":
[    9.260445][    T1] 0x000000000000-0x000000100000 : "u-boot"
[    9.267753][    T1] 0x000000100000-0x000000600000 : "uImage"
[    9.275044][    T1] 0x000000500000-0x000002a00000 : "pogoplug"
[    9.282648][    T1] 0x000002500000-0x000009100000 : "root"
[    9.288179][    T1] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0x5b00000
[    9.301405][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[    9.309987][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[    9.321644][    T1] libphy: Fixed MDIO Bus: probed
[    9.328012][    T1] libphy: orion_mdio_bus: probed
[    9.334363][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   10.081689][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:00:66:7e
[   10.091471][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   10.098766][    T1] ehci-pci: EHCI PCI platform driver
[   10.104026][    T1] ehci-orion: EHCI orion driver
[   10.108971][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[   10.115255][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[   10.123860][    T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[   10.150661][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[   10.157733][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[   10.166776][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   10.174762][    T1] usb usb1: Product: EHCI Host Controller
[   10.180367][    T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd
[   10.187824][    T1] usb usb1: SerialNumber: f1050000.ehci
[   10.193998][    T1] hub 1-0:1.0: USB hub found
[   10.198521][    T1] hub 1-0:1.0: 1 port detected
[   10.204051][    T1] usbcore: registered new interface driver usb-storage
[   10.211302][    T1] mousedev: PS/2 mouse device common for all mice
[   10.490648][   T17] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   10.692370][   T17] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01
[   10.701330][   T17] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   10.709233][   T17] usb 1-1: Product: USB2.0 Hub
[   10.714850][   T17] hub 1-1:1.0: USB hub found
[   10.719624][   T17] hub 1-1:1.0: 4 ports detected
[   11.040646][   T17] usb 1-1.3: new high-speed USB device number 3 using orion-ehci
[   11.195119][   T17] usb 1-1.3: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 2.00
[   11.204254][   T17] usb 1-1.3: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[   11.212346][   T17] usb 1-1.3: Product: DataTraveler 3.0
[   11.217688][   T17] usb 1-1.3: Manufacturer: Kingston
[   11.222797][   T17] usb 1-1.3: SerialNumber: E0D55E628FE115C0D8D70007
[   11.230076][   T17] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[   11.237709][   T17] scsi host0: usb-storage 1-1.3:1.0
[   11.290656][    T1] rtc-mv f1010300.rtc: internal RTC not ticking
[   11.296987][    T1] i2c /dev entries driver
[   11.301897][    T1] device-mapper: uevent: version 1.0.3
[   11.307544][    T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[   11.317213][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[   11.324552][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[   11.331935][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[   11.339345][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   11.346194][    T1] device-mapper: raid: Loading target version 1.15.1
[   11.354277][    T1] hid: raw HID events driver (C) Jiri Kosina
[   11.360518][    T1] drop_monitor: Initializing network drop monitor service
[   11.368060][    T1] NET: Registered protocol family 10
[   11.374667][    T1] Segment Routing with IPv6
[   11.379061][    T1] RPL Segment Routing with IPv6
[   11.383985][    T1] NET: Registered protocol family 17
[   11.389416][    T1] Key type dns_resolver registered
[   11.395014][    T1] registered taskstats version 1
[   11.399846][    T1] Loading compiled-in X.509 certificates
[   11.405854][    T1] zswap: loaded using pool lzo/zbud
[   11.411377][    T1] Key type ._fscrypt registered
[   11.416113][    T1] Key type .fscrypt registered
[   11.420829][    T1] Key type fscrypt-provisioning registered
[   11.428753][    T1] Key type big_key registered
[   11.437490][    T1] Key type encrypted registered
[   11.445709][    T1] Waiting 10 sec before mounting root device...
[   12.251979][    T7] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 3.0 0000 PQ: 0 ANSI: 4
[   12.262555][   T80] sd 0:0:0:0: [sda] 60538881 512-byte logical blocks: (31.0 GB/28.9 GiB)
[   12.271405][   T80] sd 0:0:0:0: [sda] Write Protect is off
[   12.277403][   T80] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   12.295658][   T80]  sda: sda1
[   12.301782][   T80] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   21.610648][    T1] md: Waiting for all devices to be available before autodetect
[   21.618181][    T1] md: If you don't use raid, use raid=noautodetect
[   21.624590][    T1] md: Autodetecting RAID arrays.
[   21.629403][    T1] md: autorun ...
[   21.632927][    T1] md: ... autorun DONE.
[   21.638557][    T1] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   21.654917][    T1] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[   21.662585][    T1] EXT4-fs (sda1): write access will be enabled during recovery
[   21.791471][    T1] EXT4-fs (sda1): recovery complete
[   21.799780][    T1] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[   21.809962][    T1] VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
[   21.824594][    T1] devtmpfs: mounted
[   21.831432][    T1] Freeing unused kernel memory: 1024K
[   21.837477][    T1] Checked W+X mappings: passed, no W+X pages found
[   21.843924][    T1] Run /sbin/init as init process
INIT: version 2.96 booting
Using makefile-style concurrent boot in runlevel S.
[   22.566424][  T171] ecc_sw_hamming_correct: uncorrectable ECC error
[   22.572875][  T171] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   22.584823][  T171] ecc_sw_hamming_correct: uncorrectable ECC error
[   22.591155][  T171] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   22.602550][  T171] Buffer I/O error on dev mtdblock0, logical block 255, async page read
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[   25.191646][  T287] orion_wdt: Initial timeout 21 sec
[   25.566098][  T280] usbcore: registered new interface driver uas
[   25.731501][  T281] marvell-cesa f1030000.crypto: CESA device successfully registered
[   25.758819][  T280] sd 0:0:0:0: Attached scsi generic sg0 type 0
done.
Setting hostname to 'debian'...done.
Activating swap:.
[   26.849574][  T438] EXT4-fs (sda1): re-mounted. Opts: (null). Quota mode: none.
Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.46.2 (28-Feb-2021)
rootfs: clean, 15643/1892352 files, 332064/7567104 blocks
.
[   27.144479][  T450] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
[   27.687483][    C0] random: crng init done
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
 /tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Initializing random number generator...done.
Starting Setting kernel variables: sysctl
.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:25:31:00:66:7e
Sending on   LPF/eth0/00:25:31:00:66:7e
Sending on   Socket/fallback
DHCPREQUEST for 192.168.0.15 on eth0 to 255.255.255.255 port 67
DHCPREQUEST for 192.168.0.15 on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 17
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
No DHCPOFFERS received.
Trying recorded lease 192.168.0.15
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.

--- 192.168.0.1 ping statistics ---
1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms

No working leases in persistent database - sleeping.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
999 (syslogd)
.
Starting NFS common utilities: statd idmapd.
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Not starting NFS kernel daemon: no exports. ... (warning).
Starting NTP server: ntpd.
Starting OpenBSD Secure Shell server: sshd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1036 (klogd)
.
Running local boot scripts (/etc/rc.local)
.

Debian GNU/Linux 11 debian ttyS0

debian login:
Pogo E02 was not connected with ethernet cable to internet.
After connecting the eth cable It doesn't appear on my lan.
I will try tomorrow to connect the serial cable and update the post, unfortunately in Italy is night and tomorrow I have to wake up early.
Thank you for now!



Edited 1 time(s). Last edit at 07/19/2022 03:41PM by ueghio.
Re: OLD POGO E02 update to debian
July 19, 2022 04:14PM
Marco,

Congrats! the log looks good. You are very close.

Ethernet is OK, but looks like there is no cable connected. If you plug in the cable while the system is running, check dmesg:
dmesg | tail
If there is active link to the switch/router, it should show the link is up and the speed.

You also need to fix the rootfs. There was a mis-step you did during its creation.

Quote

4. (Stock u-boot only) Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time, or running kwboot with latest u-boot image).

Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).

Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-5.13.6-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.13.6-kirkwood-tld-1 -d zImage.fdt uImage
sync

Since this ALARM u-boot is a new u-boot (comparing to stock u-boot), that supports FDT, you must not do Step 4. So reverse this step.

Log into Debian, and

cd /boot
rm zImage.fdt
mv uImage.orig uImage
sync
Note that zImage.fdt is not relevant at all, but you should remove it so later you can tell quickly that the uImage does not have DTB appended. And vice versa.

And reboot.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: OLD POGO E02 update to debian
July 20, 2022 01:48AM
Hi bodhi,I corrected the step you suggested and this is the bootlog now:


U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            60536832        8118311d-01     83
Attempting to boot from usb 0:1...
745 bytes read in 290 ms (2 KiB/s)
Importing environment (uEnv.txt)...
Checking if uenvcmd is set ...
Running default loadzimage ...
** File not found /boot/zImage **
Running default loaduimage ...
5446002 bytes read in 436 ms (11.9 MiB/s)
Running loadfdt ...
10114 bytes read in 1323 ms (6.8 KiB/s)
Running loaduinitrd ...
9671091 bytes read in 565 ms (16.3 MiB/s)
Running loaduimage ...
5446002 bytes read in 436 ms (11.9 MiB/s)
Booting from usb 0:1 ...
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-5.13.6-kirkwood-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5445938 Bytes = 5.2 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-5.13.6-kirkwood-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9671027 Bytes = 9.2 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
   Booting using the fdt blob at 0x1c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 0f1e9000, end 0fb22173 ... OK
   Loading Device Tree to 0f1e3000, end 0f1e8781 ... OK

Starting kernel ...

Uncompressing Linux...▒r▒▒▒▒▒▒▒m▒   T0] Memory policy: Data cache writeback
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000][    T0] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10
[    0.000000][    T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 240508K/262144K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 21636K reserved, 0K cma-reserved)
[    0.000000][    T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0
[    0.000000][    T0] trace event string verifier disabled
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0]  Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0]  Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    5.146587][   T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher
[    5.180175][   T59] wait_for_initramfs() called before rootfs_initcalls
[    5.378745][    T1] raid6: int32x8  gen()   108 MB/s
[    5.548733][    T1] raid6: int32x8  xor()    68 MB/s
[    5.718716][    T1] raid6: int32x4  gen()   109 MB/s
[    5.888746][    T1] raid6: int32x4  xor()    71 MB/s
[    6.058619][    T1] raid6: int32x2  gen()   139 MB/s
[    6.228722][    T1] raid6: int32x2  xor()    85 MB/s
[    6.398819][    T1] raid6: int32x1  gen()    98 MB/s
[    6.568733][    T1] raid6: int32x1  xor()    60 MB/s
[    6.573728][    T1] raid6: using algorithm int32x2 gen() 139 MB/s
[    6.579866][    T1] raid6: .... xor() 85 MB/s, rmw enabled
[    6.585378][    T1] raid6: using intx1 recovery algorithm
[    6.591105][    T1] vgaarb: loaded
[    6.595103][    T1] SCSI subsystem initialized
[    6.600148][    T1] usbcore: registered new interface driver usbfs
[    6.606425][    T1] usbcore: registered new interface driver hub
[    6.612563][    T1] usbcore: registered new device driver usb
[    6.618544][    T1] pps_core: LinuxPPS API ver. 1 registered
[    6.624256][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    6.634172][    T1] PTP clock support registered
[    6.640737][    T1] clocksource: Switched to clocksource orion_clocksource
[    6.751446][    T1] VFS: Disk quotas dquot_6.6.0
[    6.756189][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    6.792055][    T1] NET: Registered protocol family 2
[    6.797312][    T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    6.821834][    T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    6.840794][    T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    6.849225][    T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    6.880817][    T1] TCP: Hash tables configured (established 2048 bind 2048)
[    6.888178][    T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[    6.910846][    T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    6.918136][    T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    6.941021][    T1] NET: Registered protocol family 1
[    6.951060][    T1] RPC: Registered named UNIX socket transport module.
[    6.957714][    T1] RPC: Registered udp transport module.
[    6.970759][    T1] RPC: Registered tcp transport module.
[    6.976191][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    7.000761][    T1] PCI: CLS 0 bytes, default 32
[    7.005711][    T1] NetWinder Floating Point Emulator V0.97 (double precision)
[   10.081797][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:00:66:7e
[   10.091577][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   10.098872][    T1] ehci-pci: EHCI PCI platform driver
[   10.104133][    T1] ehci-orion: EHCI orion driver
[   10.109078][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[   10.115361][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[   10.123964][    T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[   10.150780][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[   10.157854][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[   10.166898][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   10.174886][    T1] usb usb1: Product: EHCI Host Controller
[   10.180489][    T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd
[   10.187947][    T1] usb usb1: SerialNumber: f1050000.ehci
[   10.194123][    T1] hub 1-0:1.0: USB hub found
[   10.198643][    T1] hub 1-0:1.0: 1 port detected
[   10.204168][    T1] usbcore: registered new interface driver usb-storage
[   10.211411][    T1] mousedev: PS/2 mouse device common for all mice
[   10.490766][   T17] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   10.692473][   T17] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01
[   10.701434][   T17] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   10.709339][   T17] usb 1-1: Product: USB2.0 Hub
[   10.714953][   T17] hub 1-1:1.0: USB hub found
[   10.719728][   T17] hub 1-1:1.0: 4 ports detected
[   11.040766][   T17] usb 1-1.3: new high-speed USB device number 3 using orion-ehci
[   11.195098][   T17] usb 1-1.3: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 2.00
[   11.204229][   T17] usb 1-1.3: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[   11.212307][   T17] usb 1-1.3: Product: DataTraveler 3.0
[   11.217664][   T17] usb 1-1.3: Manufacturer: Kingston
[   11.222769][   T17] usb 1-1.3: SerialNumber: E0D55E628FE115C0D8D70007
[   11.230052][   T17] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[   11.237691][   T17] scsi host0: usb-storage 1-1.3:1.0
[   11.290774][    T1] rtc-mv f1010300.rtc: internal RTC not ticking
[   11.297103][    T1] i2c /dev entries driver
[   11.302014][    T1] device-mapper: uevent: version 1.0.3
[   11.307667][    T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[   11.317332][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[   11.324666][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[   11.332049][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[   11.339467][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   11.346315][    T1] device-mapper: raid: Loading target version 1.15.1
[   11.354402][    T1] hid: raw HID events driver (C) Jiri Kosina
[   11.360647][    T1] drop_monitor: Initializing network drop monitor service
[   11.368194][    T1] NET: Registered protocol family 10
[   11.374794][    T1] Segment Routing with IPv6
[   11.379184][    T1] RPL Segment Routing with IPv6
[   11.384108][    T1] NET: Registered protocol family 17
[   11.389541][    T1] Key type dns_resolver registered
[   11.395136][    T1] registered taskstats version 1
[   11.399969][    T1] Loading compiled-in X.509 certificates
[   11.405975][    T1] zswap: loaded using pool lzo/zbud
[   11.411496][    T1] Key type ._fscrypt registered
[   11.416234][    T1] Key type .fscrypt registered
[   11.420952][    T1] Key type fscrypt-provisioning registered
[   11.428883][    T1] Key type big_key registered
[   11.437606][    T1] Key type encrypted registered
[   11.445824][    T1] Waiting 10 sec before mounting root device...
[   12.251957][    T7] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 3.0 0000 PQ: 0 ANSI: 4
[   12.262535][   T80] sd 0:0:0:0: [sda] 60538881 512-byte logical blocks: (31.0 GB/28.9 GiB)
[   12.271384][   T80] sd 0:0:0:0: [sda] Write Protect is off
[   12.277381][   T80] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   12.295762][   T80]  sda: sda1
[   12.301886][   T80] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   21.610768][    T1] md: Waiting for all devices to be available before autodetect
[   21.618303][    T1] md: If you don't use raid, use raid=noautodetect
[   21.624712][    T1] md: Autodetecting RAID arrays.
[   21.629534][    T1] md: autorun ...
[   21.633058][    T1] md: ... autorun DONE.
[   21.638660][    T1] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   21.655021][    T1] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[   21.662690][    T1] EXT4-fs (sda1): write access will be enabled during recovery
[   21.784791][    T1] EXT4-fs (sda1): recovery complete
[   21.793135][    T1] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[   21.803318][    T1] VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
[   21.839195][    T1] devtmpfs: mounted
[   21.846033][    T1] Freeing unused kernel memory: 1024K
[   21.852115][    T1] Checked W+X mappings: passed, no W+X pages found
[   21.858545][    T1] Run /sbin/init as init process
INIT: version 2.96 booting
Using makefile-style concurrent boot in runlevel S.
[   22.583978][  T171] ecc_sw_hamming_correct: uncorrectable ECC error
[   22.590302][  T171] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   22.602283][  T171] ecc_sw_hamming_correct: uncorrectable ECC error
[   22.608593][  T171] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   22.619992][  T171] Buffer I/O error on dev mtdblock0, logical block 255, async page read
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[   25.121979][  T282] orion_wdt: Initial timeout 21 sec
[   25.546849][  T287] usbcore: registered new interface driver uas
[   25.736501][  T279] marvell-cesa f1030000.crypto: CESA device successfully registered
[   25.773029][  T281] sd 0:0:0:0: Attached scsi generic sg0 type 0
done.
Setting hostname to 'debian'...done.
Activating swap:.
[   26.869602][  T438] EXT4-fs (sda1): re-mounted. Opts: (null). Quota mode: none.
Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.46.2 (28-Feb-2021)
rootfs: clean, 15654/1892352 files, 332086/7567104 blocks
[   27.100423][    C0] random: crng init done
.
[   27.189086][  T450] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
 /tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Initializing random number generator...done.
Starting Setting kernel variables: sysctl.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:25:31:00:66:7e
Sending on   LPF/eth0/00:25:31:00:66:7e
Sending on   Socket/fallback
DHCPREQUEST for 192.168.1.188 on eth0 to 255.255.255.255 port 67
[   33.025691][    C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   33.036348][   T17] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST for 192.168.1.188 on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPOFFER of 192.168.1.188 from 192.168.1.1
DHCPREQUEST for 192.168.1.188 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.1.188 from 192.168.1.1
bound to 192.168.1.188 -- renewal in 32835 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1003 (syslogd)
.
Starting NFS common utilities: statd idmapd.
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Not starting NFS kernel daemon: no exports. ... (warning).
Starting NTP server: ntpd.
Starting OpenBSD Secure Shell server: sshd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1045 (klogd)
.
Running local boot scripts (/etc/rc.local)
.

Debian GNU/Linux 11 debian ttyS0

debian login: marco
Password:
Linux debian 5.13.6-kirkwood-tld-1 #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021 armv5tel

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Wed Dec 31 16:01:15 PST 1969 on ttyS0
$ apt-get update
Reading package lists... Done
E: Could not open lock file /var/lib/apt/lists/lock - open (13: Permission denied)
E: Unable to lock directory /var/lib/apt/lists/
$ sudo !!
-sh: 2: sudo: not found
$ su
Password:
su: Authentication failure
$ su
Password:
root@debian:/home/marco# apt-get update
Ign:1 http://security.debian.org bullseye/updates InRelease
Err:2 http://security.debian.org bullseye/updates Release
  404  Not Found [IP: 146.75.54.132 80]
Get:4 http://ftp.us.debian.org/debian bullseye InRelease [116 kB]
Get:3 http://cdn-fastly.deb.debian.org/debian bullseye-updates InRelease [44.1 kB]
Reading package lists... Done
E: The repository 'http://security.debian.org bullseye/updates Release' does not have a Release file.
N: Updating from such a repository can't be done securely, and is therefore disabled by default.
N: See apt-secure(8) manpage for repository creation and user configuration details.
E: Release file for http://http.debian.net/debian/dists/bullseye-updates/InRelease is not valid yet (invalid for another 19193d 2h 29min 41s). Updates for this repository will not be applied.
E: Release file for http://ftp.us.debian.org/debian/dists/bullseye/InRelease is not valid yet (invalid for another 19182d 9h 41min 7s). Updates for this repository will not be applied.
I have sme problems to update the system, is there a way to fix it?
Re: OLD POGO E02 update to debian
July 20, 2022 03:44PM
Marco,

The Debian-5.13.6-kirkwood-tld-1-rootfs-bodhi.tar.bz2 rootfs release notes:

https://forum.doozan.com/read.php?2,12096
Quote

Updated 26 Sept 2021:

Basic Debian bullseye Kirkwood rootfs for most Kirwood plugs:

- tarball size: 234M
- install size: 668M
- The init system used in this rootfs is sysvinit . To boot with systemd, see Notes below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, sysvinit-utils, u-boot-tools, and mtd-utils.
- see LED controls examples in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root

Important Correction:

After releasing this rootfs,

1. I realized I've missed one package that needs to be installed in order to make fw_printenv and fw_setenv available (these binaries have been moved to package libubootenv-tool in bullseye) . So do this if you want to list or set envs in Debian.
apt-get install libubootenv-tool

2. There was an obsolete source in /etc/apt/source.list. Please change the old security repo to
deb https://security.debian.org/debian-security bullseye-security main contrib non-free



So your /etc/apt/sources.list content should look like this:

~# cat /etc/apt/sources.list
deb http://ftp.us.debian.org/debian bullseye main contrib non-free
deb-src http://ftp.us.debian.org/debian bullseye main contrib non-free

deb https://security.debian.org/debian-security bullseye-security main contrib non-free

deb  http://http.debian.net/debian bullseye-updates main contrib non-free
deb-src http://http.debian.net/debian bullseye-updates main contrib non-free

And also adjust this to your region

deb http://ftp.us.debian.org/debian bullseye main contrib non-free

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: OLD POGO E02 update to debian
July 20, 2022 04:39PM
I'm Sorry, did not ready carefully and the problem Is now fixed.
I Need to automount an External hdd to my POGO and share contents on lan.
I mount It with no problem after the boot process is complete, but i Need to automount at boot using fstab. Is It normal that Everytime i reboot the device with this ext4 external hdd connected, the boot process stops and then i loose the SSH access?
Re: OLD POGO E02 update to debian
July 20, 2022 05:14PM
> but i Need to automount at boot using
> fstab. Is It normal that Everytime i reboot the
> device with this ext4 external hdd connected, the
> boot process stops and then i loose the SSH
> access?

No, it's not normal. Your fstab should have a device statement that ignore the drive if it cannot be mounted at that time. Use the syntax similar to this tempfs. Note the last options "0 0"


tmpfs          /tmp            tmpfs   defaults          0       0


But you do not need to use fstab at all. See Wiki sticky thread:

https://forum.doozan.com/read.php?2,23630

Quote

udev

Automount USB drives with udev rules using disk label

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: OLD POGO E02 update to debian
July 21, 2022 02:44AM
I created the rule, copied and paste the code as it is but i think i'm missing sometring, because the boot process stops.
Do i need to modify the udev rule you posted with any info of my usb hdd?



Edited 2 time(s). Last edit at 07/21/2022 03:12AM by ueghio.
Re: OLD POGO E02 update to debian
July 22, 2022 03:00AM
> Do i need to modify the udev rule you posted with
> any info of my usb hdd?

No need to do any thing specific to the drive. As long as the drive has a partition label then it should work.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: OLD POGO E02 update to debian
July 24, 2022 01:37AM
yes the usb drive /dev/sdb1 is labeled "hdd".
This is the bootlog when attached:
U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
       scanning usb for storage devices... 2 Storage Device(s) found

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            1953521664      000e3529-01     83
Attempting to boot from usb 0:1...
** File not found /boot/uEnv.txt **
Checking if uenvcmd is set ...
Running default loadzimage ...
** File not found /boot/zImage **
Running default loaduimage ...
** File not found /boot/uImage **

Partition Map for USB device 1  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            60536832        8118311d-01     83
Attempting to boot from usb 1:1...
745 bytes read in 449 ms (1000 Bytes/s)
Importing environment (uEnv.txt)...
Checking if uenvcmd is set ...
Running default loadzimage ...
** File not found /boot/zImage **
Running default loaduimage ...
5446002 bytes read in 683 ms (7.6 MiB/s)
Running loadfdt ...
** File not found /boot/dts/kirkwood-pogo_e02.dtb **
Running loaduinitrd ...
** File not found /boot/uInitrd **
Running loaduimage ...
** File not found /boot/uImage **
Booting from usb 0:1 ...
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-5.13.6-kirkwood-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5445938 Bytes = 5.2 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
Wrong Ramdisk Image Format
Ramdisk image is corrupt or invalid

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            1953521664      000e3529-01     83
Attempting to boot from usb 0:1...
** File not found /boot/uEnv.txt **
Checking if uenvcmd is set ...
Running default loadzimage ...
** File not found /boot/zImage **
Running default loaduimage ...
** File not found /boot/uImage **

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            1953521664      000e3529-01     83
Attempting to boot from usb 0:1...
** File not found /boot/uEnv.txt **
Checking if uenvcmd is set ...
Running default loadzimage ...
** File not found /boot/zImage **
Running default loaduimage ...
** File not found /boot/uImage **
PogoE02>
I created udev rule with this exact content:
# NOTE: 
#       1. use pmount --sync if drive label ends with Sync/SYNC/sync in add action to allow removal without corruption
#       2. avoid mounting EFI partition for a HFS+ drive
#       3. force mount HFS+ partition as read-write
#       4. mount USB hardrive (which is identified as SSCI)

KERNEL!="sd*", GOTO="media_label_end"
ENV{ID_TYPE}!="disk", GOTO="media_label_end"

IMPORT{program}="/sbin/blkid -o udev -p %N", ENV{name}="%E{ID_FS_LABEL}"
ENV{ID_FS_TYPE}=="", GOTO="media_label_end"

ENV{ID_FS_LABEL}!="EFI", GOTO="continue"
ENV{ID_PART_TABLE_TYPE}=="gpt", GOTO="media_label_end"

LABEL="continue"

ENV{name}=="", ENV{name}="%k"

KERNEL=="sd*", SYMLINK+="usb-storage/%E{name}"

ENV{name}=="*SYNC", ENV{mode}="--sync"
ENV{name}=="*Sync", ENV{mode}="--sync"
ENV{name}=="*sync", ENV{mode}="--sync"
ENV{name}!="*SYNC", ENV{mode}=""

#ENV{ID_FS_TYPE}=="hfsplus", ENV{mode2}="--read-write"
#ENV{ID_FS_TYPE}=="hfsplus", ENV{mode3}="/bin/mount -v -o remount,force,rw /media/%E{name}"
#ENV{ID_FS_TYPE}!="hfsplus", ENV{mode3}="/usr/bin/pmount"

ACTION=="add", RUN+="/usr/bin/pmount -t %E{ID_FS_TYPE} %E{mode} %E{mode2} --noatime --umask 000 %k %E{name}"
ACTION=="add", RUN+="%E{mode3}"
ACTION=="remove", RUN+="/usr/bin/pumount --yes-I-really-want-lazy-unmount %E{name}"

LABEL="media_label_end"



Edited 1 time(s). Last edit at 07/24/2022 01:39AM by ueghio.
Re: OLD POGO E02 update to debian
July 24, 2022 03:26PM
OK, this u-boot is a bit old. There is some problem with the envs logic in scanning USB drives. It has nothing to do with the udev rules (which only run after the kernel has booted).

Unplug the USB "hdd" drive. Boot only with the USB rootfs. Let it boot all the way into Debian. Log in.

mount
dmesg | tail

And then plug in the USB hdd drive.

dmesg | tail
mount

The above is to verify that the hdd drives is mounted by udev whenever it detects the drive present.

And then we come back here and see how to fix the problem with multiple USB drives during boot.

Read this post for the explanation of this typical problem and how I solved it in my released u-boot envs. But don't try to use the instruction, it does not apply to your installed u-boot.

-bodhi
===========================
Forum Wiki
bodhi's corner
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: