|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 02, 2023 03:52PM |
Admin Registered: 13 years ago Posts: 18,997 |
OK Chris.
I think since you are booting with a new kernel. You might need to reassamble the RAID array..
See this post:
https://forum.doozan.com/read.php?3,130039,130404#msg-130404
And also the link I've mentioned in the post
If you have valuable data in the RAID array, you need to consider backing them up first. I cannot guarantee that you can keep the data. Usually a mdadm rescan will not touch the data, but you need to take precaution to back up your data first.
=====
So boot with USB rootfs and try the above. And then see if you can mount the HDD rootfs partition in md0. I know you can see them in the boot with old kernel on NAND, but you need to be able to see them while running the new kernel and USB rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I think since you are booting with a new kernel. You might need to reassamble the RAID array..
See this post:
https://forum.doozan.com/read.php?3,130039,130404#msg-130404
And also the link I've mentioned in the post
Quote
Very carefully. See posts from Mijzelf and me starting from here:
https://forum.doozan.com/read.php?2,129924,129934#msg-129934
If you have valuable data in the RAID array, you need to consider backing them up first. I cannot guarantee that you can keep the data. Usually a mdadm rescan will not touch the data, but you need to take precaution to back up your data first.
=====
So boot with USB rootfs and try the above. And then see if you can mount the HDD rootfs partition in md0. I know you can see them in the boot with old kernel on NAND, but you need to be able to see them while running the new kernel and USB rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 02, 2023 04:19PM |
Registered: 1 year ago Posts: 50 |
done that,
no changes.
Edited 1 time(s). Last edit at 06/02/2023 04:22PM by Chris.
root@debian:~# mdadm --assemble --verbose /dev/md1 /dev/sda2 /dev/sdb2
mdadm: looking for devices for /dev/md1
mdadm: /dev/sda2 is identified as a member of /dev/md1, slot 0.
mdadm: /dev/sdb2 is identified as a member of /dev/md1, slot 1.
mdadm: added /dev/sdb2 to /dev/md1 as 1
mdadm: added /dev/sda2 to /dev/md1 as 0
mdadm: /dev/md1 has been started with 2 drives.
root@debian:~# mdadm --detail /dev/md1
/dev/md1:
Version : 1.2
Creation Time : Thu Jun 1 12:00:51 2023
Raid Level : raid1
Array Size : 20954112 (19.98 GiB 21.46 GB)
Used Dev Size : 20954112 (19.98 GiB 21.46 GB)
Raid Devices : 2
Total Devices : 2
Persistence : Superblock is persistent
Update Time : Fri Jun 2 14:11:36 2023
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0
Consistency Policy : resync
Name : debian:1 (local to host debian)
UUID : 2f7360a0:e3097e58:10700f04:870cda9d
Events : 19
Number Major Minor RaidDevice State
0 8 2 0 active sync /dev/sda2
1 8 18 1 active sync /dev/sdb2
root@debian:~# mdadm --detail /dev/md2
/dev/md2:
Version : 1.2
Creation Time : Thu Jun 1 12:01:13 2023
Raid Level : raid1
Array Size : 3884791616 (3704.83 GiB 3978.03 GB)
Used Dev Size : 3884791616 (3704.83 GiB 3978.03 GB)
Raid Devices : 2
Total Devices : 2
Persistence : Superblock is persistent
Intent Bitmap : Internal
Update Time : Fri Jun 2 14:12:57 2023
State : clean, resyncing
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0
Consistency Policy : bitmap
Resync Status : 24% complete
Name : debian:2 (local to host debian)
UUID : 12a0f95c:1ff79050:ee66309f:f2d8287f
Events : 889
Number Major Minor RaidDevice State
0 8 3 0 active sync /dev/sda3
1 8 19 1 active sync /dev/sdb3
root@debian:~# mdadm --detail /dev/md0
/dev/md0:
Version : 1.2
Creation Time : Thu Jun 1 11:59:02 2023
Raid Level : raid1
Array Size : 1120256 (1094.00 MiB 1147.14 MB)
Used Dev Size : 1120256 (1094.00 MiB 1147.14 MB)
Raid Devices : 2
Total Devices : 2
Persistence : Superblock is persistent
Update Time : Thu Jun 1 11:59:14 2023
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0
Consistency Policy : resync
Name : debian:0 (local to host debian)
UUID : f642aeac:331e09dd:8ab5912a:97570362
Events : 17
Number Major Minor RaidDevice State
0 8 1 0 active sync /dev/sda1
1 8 17 1 active sync /dev/sdb1
root@debian:~# e2label /dev/md1
rootfs
root@debian:~# reboot -f
no changes.
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
Creating 1 MTD partitions on "nand0":
0x00000f500000-0x00000ff00000 : "mtd=7"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=7"
UBI: MTD device size: 10 MiB
UBI: number of good PEBs: 80
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 48
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 3/0
UBIFS: mounted UBI device 0, volume 0, name "reserve2"
UBIFS: mounted read-only
UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 200807 bytes (196 KiB)
Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)...
Done
Set lan 2 WakeOnLan ok
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> 11111111111111111111111111111111111111111<INTERRUPT>
Marvell>> setenv set_bootargs_debian 'setenv bootargs root=/dev/ram console=tty'
Marvell>> boot
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
reading /boot/uImage
5236595 bytes read in 208 ms (24 MiB/s)
reading /boot/uRamdisk
9649885 bytes read in 353 ms (26.1 MiB/s)
## Booting image at 00800000 ...
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.13.8-mvebu-tld-1
Created: 2023-06-01 17:34:24 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5236531 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-5.13.8-mvebu-tld-1
Created: 2021-09-24 7:54:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9649821 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (1
[ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=1d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing ie
[ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Ex2 Ultra
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003]
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 28
[ 0.000000][ T0] Kernel command line: root=/dev/ram console=ttyS0,115200 l
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 52428)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 )
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1011704K/1048576K available (11264K kernel code,)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x4040
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_i.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay .
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_i2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x0607000
[ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabld
[ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024B
[ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x5607001
[ 0.000001][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps evs
[ 0.008682][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff s
[ 0.020390][ T0] Switching to timer-based delay loop, resolution 1ns
[ 0.027193][ T0] Ignoring duplicate/late registration of read_current_timy
[ 0.034911][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffffs
[ 0.047019][ T0] Console: colour dummy device 80x30
[ 0.052165][ T0] Calibrating delay loop (skipped), value calculated using)
[ 0.063437][ T0] pid_max: default: 32768 minimum: 301
[ 0.068859][ T0] LSM: Security Framework initializing
[ 0.074203][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 byt)
[ 0.082188][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 819)
[ 0.091192][ T0] CPU: Testing write buffer coherency: ok
[ 0.096761][ T0] CPU0: Spectre v2: using BPIALL workaround
[ 0.102624][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.109436][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.116383][ T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.122331][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.129288][ T1] rcu: Hierarchical SRCU implementation.
[ 0.135288][ T1] smp: Bringing up secondary CPUs ...
[ 0.140913][ T1] Booting CPU 1
[ 0.144368][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.144378][ T0] CPU1: Spectre v2: using BPIALL workaround
[ 0.156525][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.161326][ T1] SMP: Total of 2 processors activated (2664.00 BogoMIPS).
[ 0.168360][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.174031][ T1] devtmpfs: initialized
[ 0.180801][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 4
[ 0.189318][ T24] wait_for_initramfs() called before rootfs_initcalls
[ 0.189464][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xfffs
[ 0.206436][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, li)
[ 0.236255][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.243390][ T1] prandom: seed boundary self test passed
[ 0.250510][ T1] prandom: 100 self tests passed
[ 0.255295][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.262367][ T1] NET: Registered protocol family 16
[ 0.268219][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocs
[ 0.276357][ T1] audit: initializing netlink subsys (disabled)
[ 0.282565][ T36] audit: type=2000 audit(0.250:1): state=initialized audit1
[ 0.283753][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.291268][ T1] cpuidle: using governor ladder
[ 0.302758][ T1] cpuidle: using governor menu
[ 0.307501][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 wa.
[ 0.316170][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.322822][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Ag
[ 0.331606][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: g
[ 0.547081][ T1] raid6: int32x8 gen() 244 MB/s
[ 0.717094][ T1] raid6: int32x8 xor() 167 MB/s
[ 0.887098][ T1] raid6: int32x4 gen() 280 MB/s
[ 1.057076][ T1] raid6: int32x4 xor() 180 MB/s
[ 1.227119][ T1] raid6: int32x2 gen() 448 MB/s
[ 1.397065][ T1] raid6: int32x2 xor() 262 MB/s
[ 1.567061][ T1] raid6: int32x1 gen() 498 MB/s
[ 1.737044][ T1] raid6: int32x1 xor() 208 MB/s
[ 1.741990][ T1] raid6: using algorithm int32x1 gen() 498 MB/s
[ 1.748065][ T1] raid6: .... xor() 208 MB/s, rmw enabled
[ 1.753616][ T1] raid6: using intx1 recovery algorithm
[ 1.759773][ T1] vgaarb: loaded
[ 1.763485][ T1] SCSI subsystem initialized
[ 1.768251][ T1] usbcore: registered new interface driver usbfs
[ 1.774452][ T1] usbcore: registered new interface driver hub
[ 1.780487][ T1] usbcore: registered new device driver usb
[ 1.786431][ T1] mc: Linux media interface: v0.10
[ 1.791435][ T1] videodev: Linux video capture interface: v2.00
[ 1.797690][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.803330][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodo>
[ 1.813145][ T1] PTP clock support registered
[ 1.819066][ T1] clocksource: Switched to clocksource arm_global_timer
[ 1.853213][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.857882][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096)
[ 1.873233][ T1] NET: Registered protocol family 2
[ 1.878388][ T1] IP idents hash table entries: 16384 (order: 5, 131072 by)
[ 1.891981][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order:)
[ 1.901146][ T1] TCP established hash table entries: 8192 (order: 3, 3276)
[ 1.909864][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.917742][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.924972][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 by)
[ 1.933094][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, line)
[ 1.940411][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes,)
[ 1.948261][ T1] NET: Registered protocol family 1
[ 1.953702][ T1] RPC: Registered named UNIX socket transport module.
[ 1.960349][ T1] RPC: Registered udp transport module.
[ 1.965728][ T1] RPC: Registered tcp transport module.
[ 1.971139][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.978252][ T1] PCI: CLS 0 bytes, default 64
[ 1.983103][ T538] Trying to unpack rootfs image as initramfs...
[ 1.989232][ T1] NetWinder Floating Point Emulator V0.97 (double precisio)
[ 2.009222][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, e
[ 2.386218][ T538] Freeing initrd memory: 9424K
[ 2.625772][ T1] Initialise system trusted keyrings
[ 2.630948][ T1] Key type blacklist registered
[ 2.635744][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 2.642964][ T1] zbud: loaded
[ 2.647128][ T1] NFS: Registering the id_resolver key type
[ 2.652893][ T1] Key type id_resolver registered
[ 2.657753][ T1] Key type id_legacy registered
[ 2.662467][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registerin.
[ 2.669850][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Re.
[ 2.677910][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 2.744280][ T1] xor: measuring software checksum speed
[ 2.754298][ T1] arm4regs : 2172 MB/sec
[ 2.765362][ T1] 8regs : 1637 MB/sec
[ 2.776086][ T1] 32regs : 1733 MB/sec
[ 2.781129][ T1] xor: using function: arm4regs (2172 MB/sec)
[ 2.787032][ T1] async_tx: api initialized (async)
[ 2.792076][ T1] Key type asymmetric registered
[ 2.796849][ T1] Asymmetric key parser 'x509' registered
[ 2.802488][ T1] bounce: pool size: 64 pages
[ 2.807134][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded)
[ 2.815288][ T1] io scheduler bfq registered
[ 2.821847][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl r
[ 2.830547][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' !
[ 2.839674][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' !
[ 2.849454][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 2.909633][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xo)
[ 2.919343][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 2.979630][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xo)
[ 3.046987][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.055991][ T1] printk: console [ttyS0] disabled
[ 3.081121][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, basA
[ 3.090826][ T1] printk: console [ttyS0] enabled
[ 3.090826][ T1] printk: console [ttyS0] enabled
[ 3.100653][ T1] printk: bootconsole [earlycon0] disabled
[ 3.100653][ T1] printk: bootconsole [earlycon0] disabled
[ 3.133104][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, basA
[ 3.144245][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dr
[ 3.152748][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dur
[ 3.161040][ T1] ahci-mvebu f10a8000.sata: supply target not found, usingr
[ 3.169638][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 porte
[ 3.179449][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only
[ 3.190086][ T1] scsi host0: ahci-mvebu
[ 3.194733][ T1] scsi host1: ahci-mvebu
[ 3.199158][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff]2
[ 3.207825][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff]2
[ 3.217683][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 3.224795][ T1] nand: Macronix MX30LF2G18AC
[ 3.229366][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 20484
[ 3.238253][ T1] Bad block table found at page 131008, version 0x01
[ 3.245488][ T1] Bad block table found at page 130944, version 0x01
[ 3.252460][ T1] 8 fixed-partitions partitions found on MTD device pxa3xx0
[ 3.260169][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0":
[ 3.266298][ T1] 0x000000000000-0x000000500000 : "U-Boot"
[ 3.272953][ T1] 0x000000500000-0x000000a00000 : "uImage"
[ 3.279498][ T1] 0x000000a00000-0x000000f00000 : "uRamdisk"
[ 3.286164][ T1] 0x000000f00000-0x00000c800000 : "image.cfs"
[ 3.293350][ T1] 0x00000c800000-0x00000d700000 : "rescue fw"
[ 3.300200][ T1] 0x00000d700000-0x00000eb00000 : "config"
[ 3.306741][ T1] 0x00000eb00000-0x00000f500000 : "reserve1"
[ 3.313456][ T1] 0x00000f500000-0x00000ff00000 : "reserve2"
[ 3.320683][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com.
[ 3.329282][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <J.
[ 3.340314][ T1] libphy: Fixed MDIO Bus: probed
[ 3.346093][ T1] libphy: orion_mdio_bus: probed
[ 3.360652][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controd
[ 3.372566][ T1] mvneta f1034000.ethernet eth0: Using random mac address c
[ 3.381540][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Drivr
[ 3.388827][ T1] ehci-pci: EHCI PCI platform driver
[ 3.394066][ T1] ehci-orion: EHCI orion driver
[ 3.398957][ T1] orion-ehci f1058000.usb: EHCI Host Controller
[ 3.405137][ T1] orion-ehci f1058000.usb: new USB bus registered, assigne1
[ 3.413563][ T1] orion-ehci f1058000.usb: irq 48, io mem 0xf1058000
[ 3.449076][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 3.455911][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct3
[ 3.464970][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, Seri1
[ 3.472960][ T1] usb usb1: Product: EHCI Host Controller
[ 3.478584][ T1] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd
[ 3.485794][ T1] usb usb1: SerialNumber: f1058000.usb
[ 3.491553][ T1] hub 1-0:1.0: USB hub found
[ 3.496054][ T1] hub 1-0:1.0: 1 port detected
[ 3.501821][ T1] usbcore: registered new interface driver usblp
[ 3.508129][ T1] usbcore: registered new interface driver usb-storage
[ 3.515141][ T1] mousedev: PS/2 mouse device common for all mice
[ 3.522491][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 3.528835][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2023)
[ 3.539811][ T1] i2c /dev entries driver
[ 3.544219][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recoverd
[ 3.553048][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recoverd
[ 3.564056][ T1] orion_wdt: Initial timeout 171 sec
[ 3.569643][ T1] device-mapper: uevent: version 1.0.3
[ 3.575181][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialim
[ 3.584590][ T1] device-mapper: multipath round-robin: version 1.2.0 loadd
[ 3.591873][ T1] device-mapper: multipath queue-length: version 0.2.0 load
[ 3.599255][ T1] device-mapper: multipath service-time: version 0.3.0 load
[ 3.606633][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 3.613467][ T1] device-mapper: raid: Loading target version 1.15.1
[ 3.622710][ T1] marvell-cesa f1090000.crypto: CESA device successfully rd
[ 3.630791][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 3.636895][ T1] usbcore: registered new interface driver usbhid
[ 3.643220][ T1] usbhid: USB HID core driver
[ 3.648027][ T1] drop_monitor: Initializing network drop monitor service
[ 3.655354][ T1] NET: Registered protocol family 10
[ 3.661275][ T1] Segment Routing with IPv6
[ 3.665662][ T1] RPL Segment Routing with IPv6
[ 3.670464][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.677971][ T1] NET: Registered protocol family 17
[ 3.683339][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 3.688279][ T1] Key type dns_resolver registered
[ 3.693379][ T1] ThumbEE CPU extension supported.
[ 3.698377][ T1] Registering SWP/SWPB emulation handler
[ 3.704226][ T1] registered taskstats version 1
[ 3.709051][ T1] Loading compiled-in X.509 certificates
[ 3.714992][ T1] zswap: loaded using pool lzo/zbud
[ 3.720327][ T1] Key type ._fscrypt registered
[ 3.725063][ T1] Key type .fscrypt registered
[ 3.729749][ T1245] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.736689][ T1] Key type fscrypt-provisioning registered
[ 3.736686][ T1240] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.737124][ T1240] ata1.00: ATA-10: WDC WD40EFAX-68JH4N1, 83.00A83, max UDM3
[ 3.750300][ T1] Key type big_key registered
[ 3.756894][ T1240] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth )
[ 3.769114][ T1245] ata2.00: ATA-10: WDC WD40EFAX-68JH4N1, 83.00A83, max UDM3
[ 3.776722][ T1245] ata2.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth )
[ 3.784371][ T1240] ata1.00: configured for UDMA/133
[ 3.784500][ T1] Key type encrypted registered
[ 3.789593][ T1245] ata2.00: configured for UDMA/133
[ 3.794418][ T23] scsi 0:0:0:0: Direct-Access ATA WDC WD40EFAX-685
[ 3.801851][ T535] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 3.809149][ T23] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4)
[ 3.814403][ T7] scsi 1:0:0:0: Direct-Access ATA WDC WD40EFAX-685
[ 3.823894][ T535] xhci-hcd f10f0000.usb3: new USB bus registered, assigned2
[ 3.832266][ T1499] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4)
[ 3.839731][ T23] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 3.848225][ T1499] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 3.854802][ T535] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci versio0
[ 3.860264][ T1499] sd 1:0:0:0: [sdb] Write Protect is off
[ 3.870115][ T23] sd 0:0:0:0: [sda] Write Protect is off
[ 3.881136][ T1499] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabA
[ 3.881526][ T535] xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000
[ 3.897594][ T23] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabA
[ 3.908416][ T535] usb usb2: New USB device found, idVendor=1d6b, idProduct3
[ 3.917458][ T535] usb usb2: New USB device strings: Mfr=3, Product=2, Seri1
[ 3.925558][ T535] usb usb2: Product: xHCI Host Controller
[ 3.931178][ T535] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 3.938402][ T535] usb usb2: SerialNumber: f10f0000.usb3
[ 3.944576][ T535] hub 2-0:1.0: USB hub found
[ 3.949100][ T535] hub 2-0:1.0: 1 port detected
[ 3.954100][ T535] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 3.960178][ T535] xhci-hcd f10f0000.usb3: new USB bus registered, assigned3
[ 3.967775][ T1499] sdb: sdb1 sdb2 sdb3
[ 3.968422][ T535] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 3.979703][ T535] usb usb3: We don't know the algorithms for LPM for this .
[ 3.988980][ T23] sda: sda1 sda2 sda3
[ 3.989550][ T1499] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 3.994003][ T23] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.005449][ T535] usb usb3: New USB device found, idVendor=1d6b, idProduct3
[ 4.014477][ T535] usb usb3: New USB device strings: Mfr=3, Product=2, Seri1
[ 4.022451][ T535] usb usb3: Product: xHCI Host Controller
[ 4.028055][ T535] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 4.035241][ T535] usb usb3: SerialNumber: f10f0000.usb3
[ 4.041043][ T535] hub 3-0:1.0: USB hub found
[ 4.045541][ T535] hub 3-0:1.0: 1 port detected
[ 4.050755][ T535] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 4.056814][ T535] xhci-hcd f10f8000.usb3: new USB bus registered, assigned4
[ 4.065138][ T535] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci versio0
[ 4.075158][ T535] xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000
[ 4.081990][ T535] usb usb4: New USB device found, idVendor=1d6b, idProduct3
[ 4.091078][ T535] usb usb4: New USB device strings: Mfr=3, Product=2, Seri1
[ 4.099200][ T535] usb usb4: Product: xHCI Host Controller
[ 4.104809][ T535] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 4.111997][ T535] usb usb4: SerialNumber: f10f8000.usb3
[ 4.117808][ T535] hub 4-0:1.0: USB hub found
[ 4.122320][ T535] hub 4-0:1.0: 1 port detected
[ 4.127211][ T535] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 4.133277][ T535] xhci-hcd f10f8000.usb3: new USB bus registered, assigned5
[ 4.141531][ T535] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 4.148673][ T535] usb usb5: We don't know the algorithms for LPM for this .
[ 4.157680][ T535] usb usb5: New USB device found, idVendor=1d6b, idProduct3
[ 4.166706][ T535] usb usb5: New USB device strings: Mfr=3, Product=2, Seri1
[ 4.174729][ T535] usb usb5: Product: xHCI Host Controller
[ 4.180346][ T535] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 4.187522][ T535] usb usb5: SerialNumber: f10f8000.usb3
[ 4.193306][ T535] hub 5-0:1.0: USB hub found
[ 4.197800][ T535] hub 5-0:1.0: 1 port detected
[ 4.203288][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/in0
[ 4.213443][ T1] Freeing unused kernel memory: 1024K
[ 4.239092][ T1443] usb 2-1: new high-speed USB device number 2 using xhci-hd
[ 4.269603][ T1] Checked W+X mappings: passed, no W+X pages found
[ 4.276003][ T1] Run /init as init process
Loading, please wait...
Starting version 247.3-6
[ 4.421869][ T1443] usb 2-1: New USB device found, idVendor=090c, idProduct=0
[ 4.439105][ T1443] usb 2-1: New USB device strings: Mfr=1, Product=2, Seria3
[ 4.446998][ T1443] usb 2-1: Product: USB Flash Disk
[ 4.462018][ T1443] usb 2-1: Manufacturer: General
[ 4.466849][ T1443] usb 2-1: SerialNumber: FBK1510272200005
[ 4.489827][ T1443] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 4.507657][ T1443] usb-storage 2-1:1.0: Quirks match for vid 090c pid 1000:0
[ 4.522014][ T1443] scsi host2: usb-storage 2-1:1.0
[ 4.574336][ T1572] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... [ 5.657575][ T1499] scsi 2:0:0:0: Di4
[ 5.668169][ T535] sd 2:0:0:0: [sdc] 3932160 512-byte logical blocks: (2.01)
[ 5.677707][ T535] sd 2:0:0:0: [sdc] Write Protect is off
[ 5.683820][ T535] sd 2:0:0:0: [sdc] No Caching mode page found
[ 5.689901][ T535] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 5.699380][ T535] sdc: sdc1 sdc2
[ 5.705009][ T535] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 5.719197][ C0] random: fast init done
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device. Common problems:
- Boot args (cat /proc/cmdline)
- Check rootdelay= (did the system wait long enough?)
- Missing modules (cat /proc/modules; ls /dev)
ALERT! /dev/ram does not exist. Dropping to a shell!
BusyBox v1.30.1 (Debian 1:1.30.1-6+b3) built-in shell (ash)
Enter 'help' for a list of built-in commands.
(initramfs) mdadm --assemble --scan
sh: mdadm: not found
(initramfs)
Edited 1 time(s). Last edit at 06/02/2023 04:22PM by Chris.
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 02, 2023 04:25PM |
Admin Registered: 13 years ago Posts: 18,997 |
> done that,
Can you show the log of the boot with USB rootfs and then how you run "mdadm --assemble --scan", and mount the rootfs partition.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Can you show the log of the boot with USB rootfs and then how you run "mdadm --assemble --scan", and mount the rootfs partition.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 02, 2023 04:34PM |
Registered: 1 year ago Posts: 50 |
herby:
and also lsblk
Edited 1 time(s). Last edit at 06/02/2023 04:40PM by Chris.
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
Creating 1 MTD partitions on "nand0":
0x00000f500000-0x00000ff00000 : "mtd=7"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=7"
UBI: MTD device size: 10 MiB
UBI: number of good PEBs: 80
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 48
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 3/0
UBIFS: mounted UBI device 0, volume 0, name "reserve2"
UBIFS: mounted read-only
UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 200807 bytes (196 KiB)
Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)...
Done
Set lan 2 WakeOnLan ok
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
reading /boot/uImage
5236595 bytes read in 207 ms (24.1 MiB/s)
reading /boot/uRamdisk
9649885 bytes read in 353 ms (26.1 MiB/s)
## Booting image at 00800000 ...
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.13.8-mvebu-tld-1
Created: 2023-06-01 17:34:24 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5236531 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-5.13.8-mvebu-tld-1
Created: 2021-09-24 7:54:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9649821 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (1
[ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=1d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing ie
[ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Ex2 Ultra
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003]
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 28
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rool
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 52428)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 )
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1011704K/1048576K available (11264K kernel code,)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x4040
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_i.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay .
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_i2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x0607000
[ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabld
[ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024B
[ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x5607001
[ 0.000001][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps evs
[ 0.008682][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff s
[ 0.020389][ T0] Switching to timer-based delay loop, resolution 1ns
[ 0.027194][ T0] Ignoring duplicate/late registration of read_current_timy
[ 0.034911][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffffs
[ 0.047020][ T0] Console: colour dummy device 80x30
[ 0.052167][ T0] Calibrating delay loop (skipped), value calculated using)
[ 0.063439][ T0] pid_max: default: 32768 minimum: 301
[ 0.068860][ T0] LSM: Security Framework initializing
[ 0.074204][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 byt)
[ 0.082189][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 819)
[ 0.091193][ T0] CPU: Testing write buffer coherency: ok
[ 0.096761][ T0] CPU0: Spectre v2: using BPIALL workaround
[ 0.102626][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.109436][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.116383][ T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.122330][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.129288][ T1] rcu: Hierarchical SRCU implementation.
[ 0.135292][ T1] smp: Bringing up secondary CPUs ...
[ 0.140915][ T1] Booting CPU 1
[ 0.144373][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.144382][ T0] CPU1: Spectre v2: using BPIALL workaround
[ 0.156528][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.161328][ T1] SMP: Total of 2 processors activated (2664.00 BogoMIPS).
[ 0.168361][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.174033][ T1] devtmpfs: initialized
[ 0.180839][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 4
[ 0.189357][ T24] wait_for_initramfs() called before rootfs_initcalls
[ 0.189500][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xfffs
[ 0.206476][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, li)
[ 0.236295][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.243431][ T1] prandom: seed boundary self test passed
[ 0.250550][ T1] prandom: 100 self tests passed
[ 0.255335][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.262408][ T1] NET: Registered protocol family 16
[ 0.268275][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocs
[ 0.276408][ T1] audit: initializing netlink subsys (disabled)
[ 0.282617][ T36] audit: type=2000 audit(0.250:1): state=initialized audit1
[ 0.283803][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.291324][ T1] cpuidle: using governor ladder
[ 0.302809][ T1] cpuidle: using governor menu
[ 0.307575][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 wa.
[ 0.316245][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.322900][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Ag
[ 0.331684][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: g
[ 0.547090][ T1] raid6: int32x8 gen() 243 MB/s
[ 0.717107][ T1] raid6: int32x8 xor() 168 MB/s
[ 0.887100][ T1] raid6: int32x4 gen() 280 MB/s
[ 1.057114][ T1] raid6: int32x4 xor() 180 MB/s
[ 1.227078][ T1] raid6: int32x2 gen() 448 MB/s
[ 1.397044][ T1] raid6: int32x2 xor() 258 MB/s
[ 1.567064][ T1] raid6: int32x1 gen() 497 MB/s
[ 1.737039][ T1] raid6: int32x1 xor() 208 MB/s
[ 1.741985][ T1] raid6: using algorithm int32x1 gen() 497 MB/s
[ 1.748063][ T1] raid6: .... xor() 208 MB/s, rmw enabled
[ 1.753614][ T1] raid6: using intx1 recovery algorithm
[ 1.759780][ T1] vgaarb: loaded
[ 1.763489][ T1] SCSI subsystem initialized
[ 1.768259][ T1] usbcore: registered new interface driver usbfs
[ 1.774458][ T1] usbcore: registered new interface driver hub
[ 1.780496][ T1] usbcore: registered new device driver usb
[ 1.786441][ T1] mc: Linux media interface: v0.10
[ 1.791446][ T1] videodev: Linux video capture interface: v2.00
[ 1.797706][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.803345][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodo>
[ 1.813159][ T1] PTP clock support registered
[ 1.819081][ T1] clocksource: Switched to clocksource arm_global_timer
[ 1.853168][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.857838][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096)
[ 1.873188][ T1] NET: Registered protocol family 2
[ 1.878341][ T1] IP idents hash table entries: 16384 (order: 5, 131072 by)
[ 1.891817][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order:)
[ 1.900987][ T1] TCP established hash table entries: 8192 (order: 3, 3276)
[ 1.909501][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.917378][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.924821][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 by)
[ 1.932949][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, line)
[ 1.940269][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes,)
[ 1.948119][ T1] NET: Registered protocol family 1
[ 1.953559][ T1] RPC: Registered named UNIX socket transport module.
[ 1.960204][ T1] RPC: Registered udp transport module.
[ 1.965583][ T1] RPC: Registered tcp transport module.
[ 1.971049][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.978162][ T1] PCI: CLS 0 bytes, default 64
[ 1.983034][ T538] Trying to unpack rootfs image as initramfs...
[ 1.989131][ T1] NetWinder Floating Point Emulator V0.97 (double precisio)
[ 2.009232][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, e
[ 2.386274][ T538] Freeing initrd memory: 9424K
[ 2.625871][ T1] Initialise system trusted keyrings
[ 2.631044][ T1] Key type blacklist registered
[ 2.635844][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 2.643066][ T1] zbud: loaded
[ 2.647223][ T1] NFS: Registering the id_resolver key type
[ 2.652992][ T1] Key type id_resolver registered
[ 2.657853][ T1] Key type id_legacy registered
[ 2.662567][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registerin.
[ 2.669950][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Re.
[ 2.678010][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 2.745382][ T1] xor: measuring software checksum speed
[ 2.755399][ T1] arm4regs : 2172 MB/sec
[ 2.766462][ T1] 8regs : 1637 MB/sec
[ 2.777187][ T1] 32regs : 1733 MB/sec
[ 2.782229][ T1] xor: using function: arm4regs (2172 MB/sec)
[ 2.788133][ T1] async_tx: api initialized (async)
[ 2.793177][ T1] Key type asymmetric registered
[ 2.797949][ T1] Asymmetric key parser 'x509' registered
[ 2.803588][ T1] bounce: pool size: 64 pages
[ 2.808229][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded)
[ 2.816379][ T1] io scheduler bfq registered
[ 2.822929][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl r
[ 2.831627][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' !
[ 2.840743][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' !
[ 2.850526][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 2.909648][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xo)
[ 2.919411][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 2.979645][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xo)
[ 3.046590][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.055607][ T1] printk: console [ttyS0] disabled
[ 3.080732][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, basA
[ 3.090406][ T1] printk: console [ttyS0] enabled
[ 3.090406][ T1] printk: console [ttyS0] enabled
[ 3.100230][ T1] printk: bootconsole [earlycon0] disabled
[ 3.100230][ T1] printk: bootconsole [earlycon0] disabled
[ 3.132691][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, basA
[ 3.143862][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dr
[ 3.152367][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dur
[ 3.160662][ T1] ahci-mvebu f10a8000.sata: supply target not found, usingr
[ 3.169261][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 porte
[ 3.179062][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only
[ 3.189692][ T1] scsi host0: ahci-mvebu
[ 3.194404][ T1] scsi host1: ahci-mvebu
[ 3.198705][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff]2
[ 3.207396][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff]2
[ 3.217382][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 3.224496][ T1] nand: Macronix MX30LF2G18AC
[ 3.229053][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 20484
[ 3.237961][ T1] Bad block table found at page 131008, version 0x01
[ 3.245196][ T1] Bad block table found at page 130944, version 0x01
[ 3.252145][ T1] 8 cmdlinepart partitions found on MTD device pxa3xx_nand0
[ 3.259423][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0":
[ 3.265552][ T1] 0x000000000000-0x000000500000 : "u-boot"
[ 3.272373][ T1] 0x000000500000-0x000000a00000 : "kernel"
[ 3.279048][ T1] 0x000000a00000-0x000000f00000 : "uRamdisk"
[ 3.285921][ T1] 0x000000f00000-0x00000c800000 : "image.cfs"
[ 3.293286][ T1] 0x00000c800000-0x00000d700000 : "rescue_fw"
[ 3.300317][ T1] 0x00000d700000-0x00000eb00000 : "config"
[ 3.307041][ T1] 0x00000eb00000-0x00000f500000 : "reserve1"
[ 3.313939][ T1] 0x00000f500000-0x00000ff00000 : "reserve2"
[ 3.321629][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com.
[ 3.330226][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <J.
[ 3.342156][ T1] libphy: Fixed MDIO Bus: probed
[ 3.348859][ T1] libphy: orion_mdio_bus: probed
[ 3.363952][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controd
[ 3.376723][ T1] mvneta f1034000.ethernet eth0: Using random mac address a
[ 3.385837][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Drivr
[ 3.393140][ T1] ehci-pci: EHCI PCI platform driver
[ 3.398411][ T1] ehci-orion: EHCI orion driver
[ 3.403321][ T1] orion-ehci f1058000.usb: EHCI Host Controller
[ 3.409491][ T1] orion-ehci f1058000.usb: new USB bus registered, assigne1
[ 3.417889][ T1] orion-ehci f1058000.usb: irq 48, io mem 0xf1058000
[ 3.449091][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 3.455922][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct3
[ 3.464963][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, Seri1
[ 3.472949][ T1] usb usb1: Product: EHCI Host Controller
[ 3.478567][ T1] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd
[ 3.485761][ T1] usb usb1: SerialNumber: f1058000.usb
[ 3.491625][ T1] hub 1-0:1.0: USB hub found
[ 3.496123][ T1] hub 1-0:1.0: 1 port detected
[ 3.502286][ T1] usbcore: registered new interface driver usblp
[ 3.508624][ T1] usbcore: registered new interface driver usb-storage
[ 3.515764][ T1] mousedev: PS/2 mouse device common for all mice
[ 3.523491][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 3.529957][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2023)
[ 3.540412][ T1] i2c /dev entries driver
[ 3.544817][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recoverd
[ 3.553762][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recoverd
[ 3.565405][ T1] orion_wdt: Initial timeout 171 sec
[ 3.571059][ T1] device-mapper: uevent: version 1.0.3
[ 3.576577][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialim
[ 3.585983][ T1] device-mapper: multipath round-robin: version 1.2.0 loadd
[ 3.593265][ T1] device-mapper: multipath queue-length: version 0.2.0 load
[ 3.600630][ T1] device-mapper: multipath service-time: version 0.3.0 load
[ 3.608008][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 3.614842][ T1] device-mapper: raid: Loading target version 1.15.1
[ 3.624214][ T1] marvell-cesa f1090000.crypto: CESA device successfully rd
[ 3.632477][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 3.638742][ T1] usbcore: registered new interface driver usbhid
[ 3.645068][ T1] usbhid: USB HID core driver
[ 3.650018][ T1] drop_monitor: Initializing network drop monitor service
[ 3.657335][ T1] NET: Registered protocol family 10
[ 3.663264][ T1] Segment Routing with IPv6
[ 3.667651][ T1] RPL Segment Routing with IPv6
[ 3.672447][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.680258][ T1] NET: Registered protocol family 17
[ 3.685552][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 3.690518][ T1] Key type dns_resolver registered
[ 3.695620][ T1] ThumbEE CPU extension supported.
[ 3.700629][ T1] Registering SWP/SWPB emulation handler
[ 3.706518][ T1] registered taskstats version 1
[ 3.709120][ T1242] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.711389][ T1] Loading compiled-in X.509 certificates
[ 3.718274][ T1240] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.724193][ T1] zswap: loaded using pool lzo/zbud
[ 3.730940][ T1242] ata2.00: ATA-10: WDC WD40EFAX-68JH4N1, 83.00A83, max UDM3
[ 3.743414][ T1242] ata2.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth )
[ 3.743540][ T1] Key type ._fscrypt registered
[ 3.751242][ T1242] ata2.00: configured for UDMA/133
[ 3.760556][ T1] Key type .fscrypt registered
[ 3.765226][ T1] Key type fscrypt-provisioning registered
[ 3.770943][ T1240] ata1.00: ATA-10: WDC WD40EFAX-68JH4N1, 83.00A83, max UDM3
[ 3.778471][ T1240] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth )
[ 3.787016][ T1] Key type big_key registered
[ 3.789585][ T1240] ata1.00: configured for UDMA/133
[ 3.806973][ T538] scsi 0:0:0:0: Direct-Access ATA WDC WD40EFAX-685
[ 3.812602][ T1] Key type encrypted registered
[ 3.820997][ T7] scsi 1:0:0:0: Direct-Access ATA WDC WD40EFAX-685
[ 3.821092][ T23] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4)
[ 3.830714][ T7] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4)
[ 3.839755][ T23] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 3.847556][ T7] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 3.854870][ T1491] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 3.859145][ T7] sd 1:0:0:0: [sdb] Write Protect is off
[ 3.865837][ T1491] xhci-hcd f10f0000.usb3: new USB bus registered, assigned2
[ 3.878638][ T23] sd 0:0:0:0: [sda] Write Protect is off
[ 3.878642][ T7] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabA
[ 3.884320][ T1491] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci versio0
[ 3.904200][ T23] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabA
[ 3.914850][ T1491] xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000
[ 3.921585][ T1491] usb usb2: New USB device found, idVendor=1d6b, idProduct3
[ 3.930625][ T1491] usb usb2: New USB device strings: Mfr=3, Product=2, Seri1
[ 3.938669][ T1491] usb usb2: Product: xHCI Host Controller
[ 3.944345][ T1491] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 3.951598][ T1491] usb usb2: SerialNumber: f10f0000.usb3
[ 3.957718][ T1491] hub 2-0:1.0: USB hub found
[ 3.962237][ T1491] hub 2-0:1.0: 1 port detected
[ 3.964612][ T7] sdb: sdb1 sdb2 sdb3
[ 3.967241][ T1491] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 3.971978][ T7] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 3.977035][ T1491] xhci-hcd f10f0000.usb3: new USB bus registered, assigned3
[ 3.991476][ T1491] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 3.992297][ T23] sda: sda1 sda2 sda3
[ 3.998617][ T1491] usb usb3: We don't know the algorithms for LPM for this .
[ 4.003790][ T23] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.011781][ T1491] usb usb3: New USB device found, idVendor=1d6b, idProduct3
[ 4.026630][ T1491] usb usb3: New USB device strings: Mfr=3, Product=2, Seri1
[ 4.034622][ T1491] usb usb3: Product: xHCI Host Controller
[ 4.040258][ T1491] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 4.047435][ T1491] usb usb3: SerialNumber: f10f0000.usb3
[ 4.053252][ T1491] hub 3-0:1.0: USB hub found
[ 4.057748][ T1491] hub 3-0:1.0: 1 port detected
[ 4.062960][ T1491] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 4.069018][ T1491] xhci-hcd f10f8000.usb3: new USB bus registered, assigned4
[ 4.077347][ T1491] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci versio0
[ 4.087366][ T1491] xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000
[ 4.094177][ T1491] usb usb4: New USB device found, idVendor=1d6b, idProduct3
[ 4.103301][ T1491] usb usb4: New USB device strings: Mfr=3, Product=2, Seri1
[ 4.111390][ T1491] usb usb4: Product: xHCI Host Controller
[ 4.116996][ T1491] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 4.124179][ T1491] usb usb4: SerialNumber: f10f8000.usb3
[ 4.129996][ T1491] hub 4-0:1.0: USB hub found
[ 4.134495][ T1491] hub 4-0:1.0: 1 port detected
[ 4.139414][ T1491] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 4.145467][ T1491] xhci-hcd f10f8000.usb3: new USB bus registered, assigned5
[ 4.153722][ T1491] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 4.160873][ T1491] usb usb5: We don't know the algorithms for LPM for this .
[ 4.169872][ T1491] usb usb5: New USB device found, idVendor=1d6b, idProduct3
[ 4.178886][ T1491] usb usb5: New USB device strings: Mfr=3, Product=2, Seri1
[ 4.186909][ T1491] usb usb5: Product: xHCI Host Controller
[ 4.192527][ T1491] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 4.199712][ T1491] usb usb5: SerialNumber: f10f8000.usb3
[ 4.205482][ T1491] hub 5-0:1.0: USB hub found
[ 4.209990][ T1491] hub 5-0:1.0: 1 port detected
[ 4.215500][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/in0
[ 4.225563][ T1] Freeing unused kernel memory: 1024K
[ 4.249105][ T1443] usb 2-1: new high-speed USB device number 2 using xhci-hd
[ 4.269627][ T1] Checked W+X mappings: passed, no W+X pages found
[ 4.276029][ T1] Run /init as init process
Loading, please wait...
Starting version 247.3-6
[ 4.431070][ T1443] usb 2-1: New USB device found, idVendor=090c, idProduct=0
[ 4.443448][ T1443] usb 2-1: New USB device strings: Mfr=1, Product=2, Seria3
[ 4.457009][ T1443] usb 2-1: Product: USB Flash Disk
[ 4.465583][ T1443] usb 2-1: Manufacturer: General
[ 4.470451][ T1443] usb 2-1: SerialNumber: FBK1510272200005
[ 4.483748][ T1443] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 4.502549][ T1443] usb-storage 2-1:1.0: Quirks match for vid 090c pid 1000:0
[ 4.519577][ T1443] scsi host2: usb-storage 2-1:1.0
[ 4.612064][ T1577] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 5.659502][ T7] scsi 2:0:0:0: Direct-Access General USB Flash Disk 4
[ 5.671366][ T1491] sd 2:0:0:0: [sdc] 3932160 512-byte logical blocks: (2.01)
[ 5.689703][ T1491] sd 2:0:0:0: [sdc] Write Protect is off
[ 5.695809][ T1491] sd 2:0:0:0: [sdc] No Caching mode page found
[ 5.701899][ T1491] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 5.711856][ T1491] sdc: sdc1 sdc2
[ 5.717020][ C0] random: fast init done
[ 5.722520][ T1491] sd 2:0:0:0: [sdc] Attached SCSI removable disk
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext3 (1) -- /dev/sdc2] fsck.ext3 -a -C0 /dev/sdc2
rootfs: clean, 30023/110208 files, 403777/440064 blocks
done.
[ 6.201725][ T1603] EXT4-fs (sdc2): mounting ext3 file system using the ext4m
[ 6.236653][ T1603] EXT4-fs (sdc2): mounted filesystem with ordered data mod.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.96 booting
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 7.939790][ T1787] sd 0:0:0:0: Att0
[ 7.969747][ T1787] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 7.988522][ T1787] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 8.244490][ T1817] md/raid1:md0: active with 2 out of 2 mirrors
[ 8.251369][ T1817] md0: detected capacity change from 0 to 2240512
[ 8.257932][ T1822] md/raid1:md2: not clean -- starting background reconstrun
[ 8.267977][ T1832] md/raid1:md1: active with 2 out of 2 mirrors
[ 8.268578][ T1822] md/raid1:md2: active with 2 out of 2 mirrors
[ 8.274362][ T1832] md1: detected capacity change from 0 to 41908224
[ 8.350773][ T1822] md2: detected capacity change from 0 to 7769583232
[ 8.361286][ T1841] md: resync of RAID array md2
[ 8.839832][ C0] random: crng init done
done.
Activating swap:.
[ 10.040631][ T1946] EXT4-fs (sdc2): re-mounted. Opts: (null). Quota mode: no.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Starting early crypto disks...done.
Setting up LVM Volume Groups...done.
Starting remaining crypto disks...done.
Will now check all file systems.
Checking all file systems.
/dev/md1 is not mounted
[/sbin/fsck.ext4 (1) -- /mnt/root] fsck.ext4 -y -C0 /dev/md1
e2fsck 1.46.2 (28-Feb-2021)
rootfs: recovering journal
rootfs: clean, 39311/1310720 files, 537559/5238528 blocks
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
[ 12.504982][ T2218] EXT4-fs (md1): mounted filesystem with ordered data mode.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Initializing random number generator...done.
Starting Setting kernel variables: sysctl.
[ 13.270042][ T2377] mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00)
[ 13.282095][ T2377] mvneta f1034000.ethernet eth0: configuring for phy/sgmiie
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on Socket/fallback
DHCPREQUEST for 192.168.1.210 on eth0 to 255.255.255.255 port 67
[ 16.419553][ T2378] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full -f
[ 16.428807][ T2378] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST for 192.168.1.210 on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPOFFER of 192.168.1.210 from 192.168.1.10
DHCPREQUEST for 192.168.1.210 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.1.210 from 192.168.1.10
bound to 192.168.1.210 -- renewal in 769594 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting LVM2 poll daemon: lvmpolld.
Not starting NFS kernel daemon: no exports. ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2547 (syslogd)
.
Starting MD monitoring service: mdadm --monitor.
Starting periodic command scheduler: cron.
Starting NTP server: ntpd.
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2605 (klogd)
.
Running local boot scripts (/etc/rc.local)
Cannot read environment, using default
Cannot read default environment from file
<13>Jun 2 14:32:23 root[2683]: Cannot read u-boot env ethaddr
.
Debian GNU/Linux 11 debian ttyS0
debian login: root
rootPassword:
Linux debian 5.13.8-mvebu-tld-1 #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 arl
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Fri Jun 2 14:15:33 PDT 2023 on ttyS0
debian
192.168.1.210
WD MyCloud Ex2 Ultra
Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, 1
Debian 11.7
Fri Jun 2 14:32:31 PDT 2023 up 1 minute
root@debian:~# mdadm --assemble --scan
root@debian:~# mount /dev/md1 /mnt/root
root@debian:~# cd /mnt/root
root@debian:/mnt/root# ls
. dev lost+found root tmp
.. etc media run usr
Debian-5.13.8-mvebu-tld-1-rootfs-bodhi.tar.bz2 export mnt sbin var
bin home opt srv
boot lib proc sys
root@debian:/mnt/root#
and also lsblk
root@debian:/mnt/root# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 1 3.6T 0 disk |-sda1 8:1 1 1.1G 0 part | `-md0 9:0 0 1.1G 0 raid1 |-sda2 8:2 1 20G 0 part | `-md1 9:1 0 20G 0 raid1 /mnt/root `-sda3 8:3 1 3.6T 0 part `-md2 9:2 0 3.6T 0 raid1 sdb 8:16 1 3.6T 0 disk |-sdb1 8:17 1 1.1G 0 part | `-md0 9:0 0 1.1G 0 raid1 |-sdb2 8:18 1 20G 0 part | `-md1 9:1 0 20G 0 raid1 /mnt/root `-sdb3 8:19 1 3.6T 0 part `-md2 9:2 0 3.6T 0 raid1 sdc 8:32 1 1.9G 0 disk |-sdc1 8:33 1 200M 0 part `-sdc2 8:34 1 1.7G 0 part / mtdblock0 31:0 0 5M 0 disk mtdblock1 31:1 0 5M 0 disk mtdblock2 31:2 0 5M 0 disk mtdblock3 31:3 0 185M 0 disk mtdblock4 31:4 0 15M 0 disk mtdblock5 31:5 0 20M 0 disk mtdblock6 31:6 0 10M 0 disk mtdblock7 31:7 0 10M 0 disk
Edited 1 time(s). Last edit at 06/02/2023 04:40PM by Chris.
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 02, 2023 06:03PM |
Admin Registered: 13 years ago Posts: 18,997 |
Chris,
Cool!
So it is just a matter of fstab and the label of this rootfs in /mnt/root.
Perhaps somebody is running RAID on their box can chime in to help here? My RAIDfu is rusty, since I'm not running RAID at all for home NAS (I think it is overkilled).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 06/02/2023 06:04PM by bodhi.
[ 8.244490][ T1817] md/raid1:md0: active with 2 out of 2 mirrors [ 8.251369][ T1817] md0: detected capacity change from 0 to 2240512 [ 8.257932][ T1822] md/raid1:md2: not clean -- starting background reconstrun [ 8.267977][ T1832] md/raid1:md1: active with 2 out of 2 mirrors [ 8.268578][ T1822] md/raid1:md2: active with 2 out of 2 mirrors [ 8.274362][ T1832] md1: detected capacity change from 0 to 41908224 [ 8.350773][ T1822] md2: detected capacity change from 0 to 7769583232 [ 8.361286][ T1841] md: resync of RAID array md2
> root@debian:~# mdadm --assemble --scan > root@debian:~# mount /dev/md1 /mnt/root > root@debian:~# cd /mnt/root > root@debian:/mnt/root# ls > . > dev lost+found root tmp > .. > etc media run usr > Debian-5.13.8-mvebu-tld-1-rootfs-bodhi.tar.bz2 > export mnt sbin var > bin > home opt srv > boot > lib proc sys
> root@debian:/mnt/root# lsblk > NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT > sda 8:0 1 3.6T 0 disk > |-sda1 8:1 1 1.1G 0 part > | `-md0 9:0 0 1.1G 0 raid1 > |-sda2 8:2 1 20G 0 part > | `-md1 9:1 0 20G 0 raid1 /mnt/root > `-sda3 8:3 1 3.6T 0 part > `-md2 9:2 0 3.6T 0 raid1 > sdb 8:16 1 3.6T 0 disk > |-sdb1 8:17 1 1.1G 0 part > | `-md0 9:0 0 1.1G 0 raid1 > |-sdb2 8:18 1 20G 0 part > | `-md1 9:1 0 20G 0 raid1 /mnt/root > `-sdb3 8:19 1 3.6T 0 part > `-md2 9:2 0 3.6T 0 raid1 > sdc 8:32 1 1.9G 0 disk > |-sdc1 8:33 1 200M 0 part > `-sdc2 8:34 1 1.7G 0 part / > mtdblock0 31:0 0 5M 0 disk > mtdblock1 31:1 0 5M 0 disk > mtdblock2 31:2 0 5M 0 disk > mtdblock3 31:3 0 185M 0 disk /mnt/root > mtdblock4 31:4 0 15M 0 disk > mtdblock5 31:5 0 20M 0 disk > mtdblock6 31:6 0 10M 0 disk > mtdblock7 31:7 0 10M 0 disk >
Cool!
So it is just a matter of fstab and the label of this rootfs in /mnt/root.
Perhaps somebody is running RAID on their box can chime in to help here? My RAIDfu is rusty, since I'm not running RAID at all for home NAS (I think it is overkilled).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 06/02/2023 06:04PM by bodhi.
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 02, 2023 06:12PM |
Admin Registered: 13 years ago Posts: 18,997 |
Usually, the rootfs is on md0.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 12:58AM |
Registered: 1 year ago Posts: 50 |
so final words,
I've tryed to change it to md0, doesn't boot
now I've deledet mdo and changed only to /dev/sda1 to rootfs and it's booting
another question the update to newr kernel doesn't work
I've tryed to change it to md0, doesn't boot
now I've deledet mdo and changed only to /dev/sda1 to rootfs and it's booting
another question the update to newr kernel doesn't work
2023-06-02 22:48:46 (15.4 MB/s) - 'linux-6.2.8-mvebu-tld-1-bodhi.tar.bz2' saved [37044194/37044194] root@debian:/boot# tar -xjf linux-6.2.8-mvebu-tld-1-bodhi.tar.bz2 root@debian:/boot# tar -xf linux-dtb-6.2.8-mvebu-tld-1.tar root@debian:/boot# cp -a zImage-6.2.8-mvebu-tld-1 zImage.fdt root@debian:/boot# cat dts/armada-385-wd-ex2-ultra.dtb >> zImage.fdt root@debian:/boot# mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.2.8-mvebu-tld-1 -d zImage.fdt uImage Image Name: Linux-6.2.8-mvebu-tld-1 Created: Fri Jun 2 22:50:03 2023 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4960940 Bytes = 4844.67 KiB = 4.73 MiB Load Address: 00008000 Entry Point: 00008000 root@debian:/boot# mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-6.2.8-mvebu-tld-1 -d initrd.img-6.2.8-mvebu-tld-1 uInitrd mkimage: Can't open initrd.img-6.2.8-mvebu-tld-1: No such file or directory
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 02:38PM |
Admin Registered: 13 years ago Posts: 18,997 |
Chris,
> now I've deledet mdo and changed only to /dev/sda1
> to rootfs and it's booting
That's what I would do.
> another question the update to newr kernel doesn't
> work
>
You've missed Step 3.
A kernel is not installed until you run dpkg (even though you can boot with the kernel zImage, the rootfs does not match the kernel). dpkg populate all kernel files in the rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> now I've deledet mdo and changed only to /dev/sda1
> to rootfs and it's booting
That's what I would do.
> another question the update to newr kernel doesn't
> work
>
> 2023-06-02 22:48:46 (15.4 MB/s) - > 'linux-6.2.8-mvebu-tld-1-bodhi.tar.bz2' saved > [37044194/37044194] > > root@debian:/boot# tar -xjf > linux-6.2.8-mvebu-tld-1-bodhi.tar.bz2 > root@debian:/boot# tar -xf > linux-dtb-6.2.8-mvebu-tld-1.tar > root@debian:/boot# cp -a zImage-6.2.8-mvebu-tld-1 > zImage.fdt > root@debian:/boot# cat > dts/armada-385-wd-ex2-ultra.dtb >> zImage.fdt > root@debian:/boot# mkimage -A arm -O linux -T > kernel -C none -a 0x00008000 -e 0x00008000 -n > Linux-6.2.8-mvebu-tld-1 -d zImage.fdt uImage > Image Name: Linux-6.2.8-mvebu-tld-1 > Created: Fri Jun 2 22:50:03 2023 > Image Type: ARM Linux Kernel Image > (uncompressed) > Data Size: 4960940 Bytes = 4844.67 KiB = 4.73 > MiB > Load Address: 00008000 > Entry Point: 00008000 > root@debian:/boot# mkimage -A arm -O linux -T > ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n > initramfs-6.2.8-mvebu-tld-1 -d > initrd.img-6.2.8-mvebu-tld-1 uInitrd > mkimage: Can't open initrd.img-6.2.8-mvebu-tld-1: > No such file or directory >
You've missed Step 3.
Quote
https://forum.doozan.com/read.php?2,32146
2. Extract the kernel and the DTB files in the archive:
cd /boot
tar -xjf linux-6.2.8-mvebu-tld-1-bodhi.tar.bz2
tar -xf linux-dtb-6.2.8-mvebu-tld-1.tar
3. And install it with dpkg. Remove flash-kernel first to avoid potential problem (if flash-kernel was not installed then you'll see some error output):
cd /boot
apt-get remove flash-kernel
dpkg -i linux-image-6.2.8-mvebu-tld-1_1.0_armhf.deb
4. Create uImage and uInitrd (kernel file initrd.img-6.2.8-mvebu-tld-1 was generated by dpkg in step 3). I am using the Zyxel NAS326 as an example here. Please replace armada-380-zyxel-nas326.dtb below with the appropriate DTB name for your box.
A kernel is not installed until you run dpkg (even though you can boot with the kernel zImage, the rootfs does not match the kernel). dpkg populate all kernel files in the rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 02:46PM |
Registered: 1 year ago Posts: 50 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 02:56PM |
Admin Registered: 13 years ago Posts: 18,997 |
Chris,
> do I need to copy now the uImage and uInitrd to
> the stick?
If you intend to use the stick as a rescue system then you should install the new kernel on the USB rootfs. Remove the HDD, and boot back to USB, and then do the kernel installation.
If you don't think you would use the USB rootfs at all, then copying the kernel files only would be OK.
As I mentioned
=====
Also see here
https://forum.doozan.com/read.php?2,111249,111249#msg-111249
Once in a while, you can instert the stick while the system is running. And run the rsync.backup.ondemand to backup th HDD rootf to the USB drive. That way you don't need to do any manual step to keep the USB stick in sync with the HDD rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> do I need to copy now the uImage and uInitrd to
> the stick?
If you intend to use the stick as a rescue system then you should install the new kernel on the USB rootfs. Remove the HDD, and boot back to USB, and then do the kernel installation.
If you don't think you would use the USB rootfs at all, then copying the kernel files only would be OK.
As I mentioned
Quote
A kernel is not installed until you run dpkg (even though you can boot with the kernel zImage, the rootfs does not match the kernel). dpkg populate all kernel files in the rootfs.
=====
Also see here
https://forum.doozan.com/read.php?2,111249,111249#msg-111249
Quote
B. Setup rsync to back up a live rootfs to a local USB drive
Once in a while, you can instert the stick while the system is running. And run the rsync.backup.ondemand to backup th HDD rootf to the USB drive. That way you don't need to do any manual step to keep the USB stick in sync with the HDD rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 02:59PM |
Registered: 1 year ago Posts: 50 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 03:04PM |
Admin Registered: 13 years ago Posts: 18,997 |
Chris,
> But I am booting the uImage and uInitrd from the
> stick.
> Can I boot somehow direct from HDD?
Yes you can. I forgot that's where you are.
> It didn't work because uInitrd is too big, no?
Not that reason. You have updated u-boot so the initrd size is irrelevant. We need to changes some envs to make it boot HDD rootfs. Also make it boot USB if the HDD rootfs has probem. I'll show you how to do that.
With serial console, power up (or reboot). Interrupt u-boot countdown and,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> But I am booting the uImage and uInitrd from the
> stick.
> Can I boot somehow direct from HDD?
Yes you can. I forgot that's where you are.
> It didn't work because uInitrd is too big, no?
Not that reason. You have updated u-boot so the initrd size is irrelevant. We need to changes some envs to make it boot HDD rootfs. Also make it boot USB if the HDD rootfs has probem. I'll show you how to do that.
With serial console, power up (or reboot). Interrupt u-boot countdown and,
printenvPlease post the log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 03:10PM |
Registered: 1 year ago Posts: 50 |
It boots HDD rotfs but not with RAID
that's why I changed to without RAID instead /dev/sda1
that's why I changed to without RAID instead /dev/sda1
Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_debian_usb=usb start; sleep 5; fatload usb 0:1 0x00800000 /boot/uImage; fatload usb 0:1 0x02100000 /boot/uRamdisk; bootm 0x00800000 0x02100000 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNet Config video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=run set_bootargs_debian; run boot_debian_usb; reset bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_r oot nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enabl e=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip :$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.l cd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock=echo Booting from stock ... ; run\ et_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa 00000 0xf00000 bootcmd_usb=echo Booting from USB ...; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then boot m $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi; usb stop bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:00:1b:51 eth1mtu=1500 eth2addr=00:50:43:00:29:51 eth2mtu=1500 eth3addr=00:50:43:1b:29:00 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:29:1b:51 ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; fatload $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000020 load_initrd=echo loading uInitrd ...; fatload $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(co nfig),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:51:29:00 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes sata_init=mw.l f1018100 20420000; mw.l f1018140 003ca800; sleep 3; scsi init script_addr_r=3000000 script_name=boot.scr scsidevs=0 serverip=192.168.11.114 set_bootargs_debian=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m @10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=ser ial set_bootargs_stock=setenv bootargs root=/dev/ram console=ttyS0,115200 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$server ip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial init=/bin/ systemd" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4541/524284 bytes Marvell>>
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 03:28PM |
Admin Registered: 13 years ago Posts: 18,997 |
I see,
So you are still booting with the FAT USB drive using fatload.
See this Step 4 in this thread.
https://forum.doozan.com/read.php?2,133718,133722#msg-133722
The new u-boot can boot with Ext3 file system.
=====
OK now you should create a new rootfs on a new USB stick using Debian-5.13.8-mvebu-tld-1-rootfs-bodhi.tar.bz2. Just like you did for the HDD rootfs. You should use Ext3 file system, don't use Ext4.
Plug in the USB roofs, remove the HDD rootfs. Power up, interrupt u-boot countdown and,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
boot_debian_usb=usb start; sleep 5; fatload usb 0:1 0x00800000 /boot/uImage; fatload usb 0:1 0x02100000 /boot/uRamdisk; bootm 0x00800000 0x02100000 bootcmd=run set_bootargs_debian; run boot_debian_usb; reset
So you are still booting with the FAT USB drive using fatload.
See this Step 4 in this thread.
https://forum.doozan.com/read.php?2,133718,133722#msg-133722
The new u-boot can boot with Ext3 file system.
Quote
Marvell>> ext2load usb 0:1 0x00800000 boot/uImage
5236595 bytes read in 576 ms (8.7 MiB/s)
Marvell>> ext2load usb 0:1 0x02100000 boot/uRamdisk
9649885 bytes read in 736 ms (12.5 MiB/s)
=====
OK now you should create a new rootfs on a new USB stick using Debian-5.13.8-mvebu-tld-1-rootfs-bodhi.tar.bz2. Just like you did for the HDD rootfs. You should use Ext3 file system, don't use Ext4.
Plug in the USB roofs, remove the HDD rootfs. Power up, interrupt u-boot countdown and,
setenv boot_debian_usb 'usb start; sleep 5; ext2load usb 0:1 0x00800000 boot/uImage; ext2load usb 0:1 0x02100000 boot/uInitrd; bootm 0x00800000 0x02100000' boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:12PM |
Registered: 1 year ago Posts: 50 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:22PM |
Admin Registered: 13 years ago Posts: 18,997 |
> boot successful :)
Cool!
> Next step?
> I'm starting to be sleepy, here is 23 ...
Come back tomorrow and try these next steps (before I'll wake up in PST timezone :)
Remove the USB roofs, and plug in the HDD rootfs. Power up, interrupt u-boot countdown and,
Failed or successful, please post the entire serial console log (until the Debian login prompt). We are setting an example how to boot with the HDD rootfs here if it is successful.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Cool!
> Next step?
> I'm starting to be sleepy, here is 23 ...
Come back tomorrow and try these next steps (before I'll wake up in PST timezone :)
Remove the USB roofs, and plug in the HDD rootfs. Power up, interrupt u-boot countdown and,
ide resetIf the output shows that the HDD is initialized with capacity,... then do,
ext2ls ide 0:1 /bootIf the files are listed correctly then do,
sleep 5; ext2load ide 0:1 0x00800000 boot/uImage; ext2load ide 0:1 0x02100000 boot/uInitrd; bootm 0x00800000 0x02100000' boot
Failed or successful, please post the entire serial console log (until the Debian login prompt). We are setting an example how to boot with the HDD rootfs here if it is successful.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:23PM |
Registered: 1 year ago Posts: 50 |
Bodhi,
I see you posted a new kernel. Nice.
there is a typing mistake
the kernel name is:
and the dpkg
i think this is the right one
I see you posted a new kernel. Nice.
there is a typing mistake
the kernel name is:
linux-image-6.3.5-mvebu-tld-1_1_armhf.deb
and the dpkg
dpkg -i linux-image-6.3.5-mvebu-tld-1_1.0_armhf.debhas a .0 too much
i think this is the right one
dpkg -i linux-image-6.3.5-mvebu-tld-1_1_armhf.debor the kernel needs it?
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:25PM |
Admin Registered: 13 years ago Posts: 18,997 |
Chris,
I've corrected the typos (thanks bluzfanmr1).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I've corrected the typos (thanks bluzfanmr1).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:30PM |
Registered: 1 year ago Posts: 50 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:36PM |
Admin Registered: 13 years ago Posts: 18,997 |
How about:
If the files are listed correctly then do,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 06/03/2023 04:37PM by bodhi.
scsi reset sleep 5 ext2ls scsi 0:1 /bootor if scsi reset failed:
scsi init
If the files are listed correctly then do,
ext2load scsi 0:1 0x00800000 boot/uImage; ext2load scsi 0:1 0x02100000 boot/uInitrd; bootm 0x00800000 0x02100000' boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 06/03/2023 04:37PM by bodhi.
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:38PM |
Registered: 1 year ago Posts: 50 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:39PM |
Admin Registered: 13 years ago Posts: 18,997 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:43PM |
Admin Registered: 13 years ago Posts: 18,997 |
Ah! I forgot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
run sata_init sleep 5 ext2ls scsi 0:1 /bootIf the files are listed correctly then do,
ext2load scsi 0:1 0x00800000 boot/uImage; ext2load scsi 0:1 0x02100000 boot/uInitrd; bootm 0x00800000 0x02100000' boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:43PM |
Registered: 1 year ago Posts: 50 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:47PM |
Admin Registered: 13 years ago Posts: 18,997 |
bodhi Wrote:
-------------------------------------------------------
> Ah! I forgot.
>
>
>
See above.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Ah! I forgot.
>
>
> run sata_init > sleep 5 > ext2ls scsi 0:1 /boot >> If the files are listed correctly then do,
>
> ext2load scsi 0:1 0x00800000 boot/uImage; ext2load > scsi 0:1 0x02100000 boot/uInitrd; bootm 0x00800000 > 0x02100000' > boot >
See above.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:47PM |
Registered: 1 year ago Posts: 50 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:49PM |
Admin Registered: 13 years ago Posts: 18,997 |
run sata_init sleep 5
Do it a few times
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:52PM |
Registered: 1 year ago Posts: 50 |
Nope
The HDD's are running
The HDD's are running
Marvell>> run sata_init Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Found 0 device(s). Marvell>> run sata_init Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Found 0 device(s). Marvell>> sleep5 Unknown command 'sleep5' - try 'help' Marvell>> sleep 5 Marvell>> run sata_init Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Found 0 device(s). Marvell>> run sata_init Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Found 0 device(s). Marvell>> sleep 5 Marvell>> run sata_init Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Found 0 device(s). Marvell>> run sata_init Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Found 0 device(s). Marvell>>
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:56PM |
Admin Registered: 13 years ago Posts: 18,997 |
OK, we'll pick it up tomorrow.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition June 03, 2023 04:57PM |
Registered: 1 year ago Posts: 50 |
