Welcome! Log In Create A New Profile

Advanced

Upgrading to Debian stretch

Posted by bodhi 
Re: Upgrading to Debian stretch
January 30, 2018 12:50PM
Now I have set the label as told to rootfs correctly.

root@debian:~# e2label /dev/sdb1
rootfs
root@debian:~#

But still I have no luck. :( The kernel failed to run. The LED color is still amber.

Yes, I don't have a serial console with a physical cable attached. At the moment I can only use the netconsole as mentioned in the other thread.

Any chance to get it work? :)

Tom
Re: Upgrading to Debian stretch
January 30, 2018 03:27PM
Tom,

> Yes, I don't have a serial console with a physical
> cable attached. At the moment I can only use the
> netconsole as mentioned in the other thread.
>
> Any chance to get it work? :)

It is quite easy to run a new rootfs using Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 from the release thread:
https://forum.doozan.com/read.php?2,12096

Your current rootfs must have something wrong that we cannot see easily without serial console. So if you need to keep your current rootfs and only upgrade, I think you should connect serial console. After that, this problem can be solved in a few minutes.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Upgrading to Debian stretch
January 31, 2018 03:48PM
Strange....

The Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi is also not working. Same behavior as before with the other kernel.

Maybe still an incorrect environment var?

arcNumber=2097
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootcmd_pogo=run bootcmd_rescue
bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
bootdelay=10
console=ttyS0,115200
ethact=egiga0
ethaddr=00:10:75:1A:B8:8D
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
if_netconsole=ping $serverip
ipaddr=192.168.0.16
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
ncip=192.168.0.1
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
preboot=run if_netconsole start_netconsole
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=1
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
serverip=192.168.0.1
set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=nc
stdin=nc
stdout=nc
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext2
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params

Environment size: 2839/131068 bytes
u-boot>>
Tom
Re: Upgrading to Debian stretch
January 31, 2018 04:53PM
Tom,

We are going way off topic here. So please create a new thread for this booting problem and post the complete boot log of your attempt to boot Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.

-bodhi
===========================
Forum Wiki
bodhi's corner
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: