Re: HP T5325 with bad flash - what to do? September 11, 2017 02:12PM |
Registered: 6 years ago Posts: 85 |
Re: HP T5325 with bad flash - what to do? September 11, 2017 02:18PM |
Admin Registered: 13 years ago Posts: 18,590 |
Re: HP T5325 with bad flash - what to do? September 11, 2017 02:19PM |
Admin Registered: 13 years ago Posts: 18,590 |
Re: HP T5325 with bad flash - what to do? September 11, 2017 02:22PM |
Registered: 6 years ago Posts: 85 |
Re: HP T5325 with bad flash - what to do? September 12, 2017 01:10AM |
Admin Registered: 13 years ago Posts: 18,590 |
Re: HP T5325 with bad flash - what to do? September 12, 2017 01:54AM |
Registered: 6 years ago Posts: 85 |
Re: HP T5325 with bad flash - what to do? September 12, 2017 03:02AM |
Registered: 7 years ago Posts: 310 |
sudo apt-get install picocom
picocom /dev/ttyUSB0 -b 115200in a terminal
Re: HP T5325 with bad flash - what to do? September 12, 2017 07:24AM |
Registered: 6 years ago Posts: 85 |
root@debian64:/home/kalehrl# picocom /dev/ttyUSB0 -b 115200 picocom v1.7 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready �� _ _ .____ | |_| | | _ \ | _ | | (_)) | |-| | | | |_| |_| |_| .. _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Jan 8 2010 - 14:03:56) MIC version : 3.4.19-16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD4E0 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [1024kB@f8000000] Flash: 1 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: SM22 Firm: I052 Ser#: (03)5526888-20080228 Type: Hard Disk Capacity: 463.6 MB = 0.4 GB (949536 x 512) 1888432 bytes read Checking Button Status: off Checking GotoWOL Status: off ## Booting image at 00200000 ... Image Name: Linux-2.6.22.18-2-armel Created: 2009-11-17 18:35:01 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1888368 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux......................................................................................................................... done, booting the kernel.
Re: HP T5325 with bad flash - what to do? September 12, 2017 07:18PM |
Admin Registered: 13 years ago Posts: 18,590 |
printenv
Re: HP T5325 with bad flash - what to do? September 13, 2017 01:15AM |
Registered: 6 years ago Posts: 85 |
root@debian64:/home/kalehrl# picocom /dev/ttyUSB0 -b 115200 picocom v1.7 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready � _ _ .____ | |_| | | _ \ | _ | | (_)) | |-| | | | |_| |_| |_| .. _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Jan 8 2010 - 14:03:56) MIC version : 3.4.19-16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD4E0 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [1024kB@f8000000] Flash: 1 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 HP>> printenv [U-boot variables] baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ run_diag=no console=console=ttyS0,115200 mtdparts=spi_flash:0x80000@0(uboot)ro,0x80000@0x80000(root) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage usb_bootargs=root=/dev/ram rw bootusb=usb start;fatload usb 0 0x800000 /boot/uImage.usb;fatload usb 0 0x1100000 /boot/uInitrd.usb usbboot=setenv bootargs $(usb_bootargs); run bootusb; bootm 0x800000 0x1100000 thinpro_bootargs=root=/dev/sda1 rw init=/init video=xgifb splash quiet thinpro=ide reset; ext2load ide 0:1 0x200000 /boot/uImage; wol; setenv bootargs $(thinpro_bootargs); bootm 0x200000 pcieTune=yes mfgmode=setenv bootdelay 3; setenv in_mfg yes;setenvh GotoWOL Yes; setenvh WOLEnabled No; setenv bootcmd run mfgboot; saveenv; reset mfgbootargs=setenv bootargs root=/dev/sdb1 rw init=/init ip=dhcp rootdelay=8 $(console) udevtimeout=8 mfgboot=usb start; ext2load usb 0:1 0x2000000 /boot/uImage; run mfgbootargs; bootm 0x2000000 product=setenv bootdelay 1; setenv in_mfg no;setenvh GotoWOL No; setenvh WOLEnabled Yes; setenv bootcmd run thinpro; saveenv; reset standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 ethaddr=f4:ce:46:23:fd:25 gatewayip=10.4.50.5 netmask=255.255.255.0 ipaddr=10.4.50.70 serverip=10.4.50.5 bootdelay=1 in_mfg=no bootcmd=run thinpro stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no enaAutoRecovery=yes Environment size: 1974/4092 bytes [PUE variables] manufacturer=Hewlett-Packard product_name=hp t5325 vendor=mitac mac=f4:ce:46:23:fd:25 uuid=b7726ae4-bb54-11d4-ae6a-f4ce4623fd25 serial=CN304121BS Environment size: 146/4092 bytes [HPE variables] UbootVersion=0x03041916 UbootReleaseDate=01082010 AssetNumber=0 AssetLocation=0 InitialNumlock=On ClockSpeed=1200 WOLEnabled=Yes GotoWOL=No Environment size: 140/4092 bytes HP>>
Re: HP T5325 with bad flash - what to do? September 13, 2017 06:26PM |
Admin Registered: 13 years ago Posts: 18,590 |
## Booting image at 00200000 ... Image Name: Linux-2.6.22.18-2-armel Created: 2009-11-17 18:35:01 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1888368 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux......................................................................................................................... done, booting the kernel.
Re: HP T5325 with bad flash - what to do? September 14, 2017 12:57AM |
Registered: 6 years ago Posts: 85 |
Quote
The problem booting above is most likely that the stock rootfs was corrupted. And we need to reflash that only.
Quote
About why your kwboot was stuck: please check your serial console wires to see if all 3 wires were solidly connected.
Re: HP T5325 with bad flash - what to do? September 14, 2017 03:40AM |
Admin Registered: 13 years ago Posts: 18,590 |
Re: HP T5325 with bad flash - what to do? September 14, 2017 03:43AM |
Admin Registered: 13 years ago Posts: 18,590 |
setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10' setenv load_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x1100000 /boot/uInitrd' setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x1100000 setenv bootcmd 'run bootcmd_usb; reset' setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' boot
Quote
4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).
Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).
Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-4.12.1-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage
sync
Re: HP T5325 with bad flash - what to do? September 14, 2017 07:40AM |
Registered: 6 years ago Posts: 85 |
_ _ .____ | |_| | | _ \ | _ | | (_)) | |-| | | | |_| |_| |_| .. _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Jan 8 2010 - 14:03:56) MIC version : 3.4.19-16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD4E0 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [1024kB@f8000000] Flash: 1 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 HP>> setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10' HP>> setenv load_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x1100000 /boot/uInitrd' HP>> setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x1100000 HP>> setenv bootcmd 'run bootcmd_usb; reset' HP>> setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' HP>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ......................................................................................................................................................................... 3833511 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ................................................................................................................................................................................................................. ..................................................................................................................................................................................................................................................................................................... 7245696 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-09-14 12:43:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3833447 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: HP t5325 Thin Client [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback
Re: HP T5325 with bad flash - what to do? September 14, 2017 07:09PM |
Admin Registered: 13 years ago Posts: 18,590 |
Re: HP T5325 with bad flash - what to do? September 15, 2017 12:54AM |
Registered: 6 years ago Posts: 85 |
Re: HP T5325 with bad flash - what to do? September 15, 2017 01:06AM |
Admin Registered: 13 years ago Posts: 18,590 |
Re: HP T5325 with bad flash - what to do? September 15, 2017 02:15AM |
Admin Registered: 13 years ago Posts: 18,590 |
> [ 0.000000] Booting Linux on physical CPU 0x0 > [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 > (root@tldDebian) (gcc version 4.9.2 (Debian > 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT > 2017 > [ 0.000000] CPU: Feroceon 88FR131 [56251311] > revision 1 (ARMv5TE), cr=0005397f > [ 0.000000] CPU: VIVT data cache, VIVT > instruction cache > [ 0.000000] OF: fdt: Machine model: HP t5325 > Thin Client > [ 0.000000] bootconsole [earlycon0] enabled > [ 0.000000] Memory policy: Data cache > writeback
Re: HP T5325 with bad flash - what to do? September 15, 2017 12:43PM |
Registered: 6 years ago Posts: 85 |
Re: HP T5325 with bad flash - what to do? September 15, 2017 05:00PM |
Admin Registered: 13 years ago Posts: 18,590 |
Re: HP T5325 with bad flash - what to do? September 15, 2017 05:56PM |
Registered: 6 years ago Posts: 85 |
Re: HP T5325 with bad flash - what to do? September 15, 2017 09:49PM |
Admin Registered: 13 years ago Posts: 18,590 |
Re: HP T5325 with bad flash - what to do? September 16, 2017 09:56AM |
Registered: 6 years ago Posts: 85 |
Re: HP T5325 with bad flash - what to do? September 16, 2017 05:17PM |
Admin Registered: 13 years ago Posts: 18,590 |
setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10' setenv load_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x1100000 /boot/uInitrd' setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x1100000 setenv bootcmd 'run bootcmd_usb; reset' setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootmem_debug=1' boot
Re: HP T5325 with bad flash - what to do? September 17, 2017 02:51AM |
Registered: 6 years ago Posts: 85 |
Re: HP T5325 with bad flash - what to do? September 17, 2017 06:35PM |
Admin Registered: 13 years ago Posts: 18,590 |
setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10' setenv load_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x1100000 /boot/uInitrd' setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x1100000 setenv bootcmd 'run bootcmd_usb; reset' setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootmem_debug=1 mem=256M' boot
Re: HP T5325 with bad flash - what to do? September 19, 2017 07:01AM |
Registered: 6 years ago Posts: 85 |
_ _ .____ | |_| | | _ \ | _ | | (_)) | |-| | | | |_| |_| |_| .. _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Jan 8 2010 - 14:03:56) MIC version : 3.4.19-16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD4E0 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [1024kB@f8000000] Flash: 1 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 HP>> setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10' HP>> setenv load_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x1100000 /boot/uInitrd' HP>> setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x1100000 HP>> setenv bootcmd 'run bootcmd_usb; reset' HP>> setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootmem_debug=1 mem=256M' HP>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ......................................................................................................................................................................... 3833511 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ................................................................................................................................................................................................................. ..................................................................................................................................................................................................................................................................................................... 7245696 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2013-01-01 16:26:59 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3833447 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: HP t5325 Thin Client [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootmem_debug=1 mem=256M [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 239388K/262144K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 22756K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.007905] Switching to timer-based delay loop, resolution 5ns [ 0.014307] Console: colour dummy device 80x30 [ 0.018884] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.029483] pid_max: default: 32768 minimum: 301 [ 0.034352] Security Framework initialized [ 0.038670] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.045344] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.053283] CPU: Testing write buffer coherency: ok [ 0.059202] Setting up static identity map for 0x100000 - 0x100058 [ 0.065672] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.073984] devtmpfs: initialized [ 0.081683] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.091641] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.098207] prandom: seed boundary self test passed [ 0.106864] prandom: 100 self tests passed [ 0.111075] pinctrl core: initialized pinctrl subsystem [ 0.117463] NET: Registered protocol family 16 [ 0.122477] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130938] cpuidle: using governor ladder [ 0.135163] cpuidle: using governor menu [ 0.139640] Feroceon L2: Enabling L2 [ 0.143317] Feroceon L2: Cache support initialised. [ 0.148625] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.164703] No ATAGs? [ 0.174057] vgaarb: loaded [ 0.179540] SCSI subsystem initialized [ 0.183818] usbcore: registered new interface driver usbfs [ 0.189493] usbcore: registered new interface driver hub [ 0.194937] usbcore: registered new device driver usb [ 0.201198] clocksource: Switched to clocksource orion_clocksource [ 0.295841] VFS: Disk quotas dquot_6.6.0 [ 0.299902] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.317441] NET: Registered protocol family 2 [ 0.322647] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.329690] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.336157] TCP: Hash tables configured (established 2048 bind 2048) [ 0.342662] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.348568] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.355085] NET: Registered protocol family 1 [ 0.359910] RPC: Registered named UNIX socket transport module. [ 0.365965] RPC: Registered udp transport module. [ 0.370728] RPC: Registered tcp transport module. [ 0.375523] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.382272] Unpacking initramfs... [ 0.385749] Initramfs unpacking failed: junk in compressed archive [ 0.411690] Freeing initrd memory: 7076K [ 0.415846] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.423409] audit: initializing netlink subsys (disabled) [ 0.429302] Initialise system trusted keyrings [ 0.433867] audit: type=2000 audit(0.417:1): state=initialized audit_enabled=0 res=1 [ 0.441737] Key type blacklist registered [ 0.445949] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.452573] zbud: loaded [ 0.456136] NFS: Registering the id_resolver key type [ 0.461344] Key type id_resolver registered [ 0.465596] Key type id_legacy registered [ 0.469677] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.476480] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.483115] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.490397] fuse init (API version 7.26) [ 0.494741] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.501471] orangefs_init: module version upstream loaded [ 0.506930] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.561206] random: fast init done [ 6.352351] Key type asymmetric registered [ 6.356523] Asymmetric key parser 'x509' registered [ 6.361796] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.369241] io scheduler noop registered [ 6.373298] io scheduler deadline registered [ 6.377699] io scheduler cfq registered (default) [ 6.383705] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.399046] loop: module loaded [ 6.403897] libphy: Fixed MDIO Bus: probed [ 6.408788] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.415442] ehci-pci: EHCI PCI platform driver [ 6.420005] ehci-orion: EHCI orion driver [ 6.424307] usbcore: registered new interface driver usb-storage [ 6.430696] mousedev: PS/2 mouse device common for all mice [ 6.436676] i2c /dev entries driver [ 6.440608] kirkwood-cpufreq kirkwood-cpufreq: Unable to get cpuclk [ 6.447018] kirkwood-cpufreq: probe of kirkwood-cpufreq failed with error -22 [ 6.454680] hidraw: raw HID events driver (C) Jiri Kosina [ 6.460482] drop_monitor: Initializing network drop monitor service [ 6.467057] NET: Registered protocol family 17 [ 6.471671] Key type dns_resolver registered [ 6.476801] registered taskstats version 1 [ 6.480963] Loading compiled-in X.509 certificates [ 6.485905] zswap: loaded using pool lzo/zbud [ 6.492703] Key type big_key registered [ 6.498446] Key type encrypted registered [ 6.503809] hctosys: unable to open rtc device (rtc0) [ 8.556370] Unable to handle kernel paging request at virtual address d0000000 [ 8.563644] pgd = c0004000 [ 8.566425] [d0000000] *pgd=00000000 [ 8.570077] Internal error: Oops: 5 [#1] PREEMPT ARM [ 8.575100] Modules linked in: [ 8.578232] CPU: 0 PID: 1 Comm: swapper Not tainted 4.12.1-kirkwood-tld-1 #1 [ 8.585329] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 8.591646] task: cf834e00 task.stack: cf836000 [ 8.596250] PC is at crc32_be+0x6c/0x160 [ 8.600234] LR is at 0xc0950bd0 [ 8.603442] pc : [<c0584814>] lr : [<c0950bd0>] psr: 20000053 [ 8.603442] sp : cf837ef0 ip : c09520c8 fp : 00000000 [ 8.615034] r10: c0db9ba0 r9 : c0c4b838 r8 : 0bd705dd [ 8.620314] r7 : 00000000 r6 : cffffffc r5 : 1c3e9e27 r4 : 00000007 [ 8.626889] r3 : 3e07b35d r2 : 1e1bdfbc r1 : c115f354 r0 : 2b256da3 [ 8.633473] Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none [ 8.640747] Control: 0005397f Table: 00004000 DAC: 00000053 [ 8.646544] Process swapper (pid: 1, stack limit = 0xcf836190) [ 8.652428] Stack: (0xcf837ef0 to 0xcf838000) [ 8.656847] 7ee0: c115f358 f0defde7 4e4d16c5 c0c59544 [ 8.665075] 7f00: 00000000 c0c3f8f0 00000007 c0c3f8bc 000000b8 c010178c 00000000 c01334d0 [ 8.673299] 7f20: 00000000 c0299eec 00000000 c0aeb5e0 000000b8 00000007 00000007 c0aec440 [ 8.681525] 7f40: 000000b7 c0aec440 cfffce97 cfffce9b c0d0bc24 00000007 c0c4b830 000000b8 [ 8.689750] 7f60: 00000007 c0c4b834 000000b8 c0c59544 c0db9ba0 c0c00e18 00000007 00000007 [ 8.697975] 7f80: 00000000 c0c005ac 00000000 c08331f8 00000000 00000000 00000000 00000000 [ 8.706200] 7fa0: 00000000 c0833200 00000000 c01070f0 00000000 00000000 00000000 00000000 [ 8.714425] 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 8.722651] 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 3b021025 ce6bfc62 [ 8.730889] [<c0584814>] (crc32_be) from [<c0c3f8f0>] (of_fdt_raw_init+0x34/0x78) [ 8.738432] [<c0c3f8f0>] (of_fdt_raw_init) from [<c010178c>] (do_one_initcall+0xa8/0x158) [ 8.746665] [<c010178c>] (do_one_initcall) from [<c0c00e18>] (kernel_init_freeable+0x198/0x260) [ 8.755419] [<c0c00e18>] (kernel_init_freeable) from [<c0833200>] (kernel_init+0x8/0x10c) [ 8.763653] [<c0833200>] (kernel_init) from [<c01070f0>] (ret_from_fork+0x14/0x24) [ 8.771278] Code: e1a05002 e59fe0f4 e3550000 0a00002b (e5963004) [ 8.777429] ---[ end trace 12b0d190d31fd2dc ]--- [ 8.782187] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 8.782187] [ 8.791453] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 8.791453]
Re: HP T5325 with bad flash - what to do? September 19, 2017 07:33AM |
Admin Registered: 13 years ago Posts: 18,590 |
setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10' setenv load_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x2100000 /boot/uInitrd' setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x2100000 setenv bootcmd 'run bootcmd_usb; reset' setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootmem_debug=1 mem=256M' boot
Re: HP T5325 with bad flash - what to do? September 19, 2017 07:37AM |
Registered: 6 years ago Posts: 85 |
_ _ .____ | |_| | | _ \ | _ | | (_)) | |-| | | | |_| |_| |_| .. _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (Jan 8 2010 - 14:03:56) MIC version : 3.4.19-16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD4E0 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [1024kB@f8000000] Flash: 1 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 HP>> setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10' HP>> setenv load_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x2100000 /boot/uInitrd' HP>> setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x2100000 HP>> setenv bootcmd 'run bootcmd_usb; reset' HP>> setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootmem_debug=1 mem=256M' HP>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ......................................................................................................................................................................... 3833511 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ................................................................................................................................................................................................................. ..................................................................................................................................................................................................................................................................................................... 7245696 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2013-01-01 16:26:59 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3833447 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: HP t5325 Thin Client [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootmem_debug=1 mem=256M [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 239372K/262144K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 22772K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.007905] Switching to timer-based delay loop, resolution 5ns [ 0.014306] Console: colour dummy device 80x30 [ 0.018884] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.029483] pid_max: default: 32768 minimum: 301 [ 0.034352] Security Framework initialized [ 0.038670] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.045344] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.053284] CPU: Testing write buffer coherency: ok [ 0.059202] Setting up static identity map for 0x100000 - 0x100058 [ 0.065672] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.073982] devtmpfs: initialized [ 0.081668] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.091620] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.098192] prandom: seed boundary self test passed [ 0.106856] prandom: 100 self tests passed [ 0.111067] pinctrl core: initialized pinctrl subsystem [ 0.117449] NET: Registered protocol family 16 [ 0.122461] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130926] cpuidle: using governor ladder [ 0.135147] cpuidle: using governor menu [ 0.139621] Feroceon L2: Enabling L2 [ 0.143300] Feroceon L2: Cache support initialised. [ 0.148607] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.164681] No ATAGs? [ 0.174017] vgaarb: loaded [ 0.179499] SCSI subsystem initialized [ 0.183782] usbcore: registered new interface driver usbfs [ 0.189450] usbcore: registered new interface driver hub [ 0.194894] usbcore: registered new device driver usb [ 0.201159] clocksource: Switched to clocksource orion_clocksource [ 0.295812] VFS: Disk quotas dquot_6.6.0 [ 0.299876] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.317426] NET: Registered protocol family 2 [ 0.322618] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.329664] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.336133] TCP: Hash tables configured (established 2048 bind 2048) [ 0.342635] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.348543] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.355064] NET: Registered protocol family 1 [ 0.359890] RPC: Registered named UNIX socket transport module. [ 0.365940] RPC: Registered udp transport module. [ 0.370702] RPC: Registered tcp transport module. [ 0.375497] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.382246] Unpacking initramfs... [ 1.031585] Freeing initrd memory: 7076K [ 1.035746] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.043322] audit: initializing netlink subsys (disabled) [ 1.049245] Initialise system trusted keyrings [ 1.053817] audit: type=2000 audit(1.037:1): state=initialized audit_enabled=0 res=1 [ 1.061692] Key type blacklist registered [ 1.065906] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 1.072529] zbud: loaded [ 1.076095] NFS: Registering the id_resolver key type [ 1.081306] Key type id_resolver registered [ 1.085550] Key type id_legacy registered [ 1.089631] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.096437] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.103054] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.110336] fuse init (API version 7.26) [ 1.114676] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.121397] orangefs_init: module version upstream loaded [ 1.126859] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.561166] random: fast init done [ 6.980687] Key type asymmetric registered [ 6.985160] Asymmetric key parser 'x509' registered [ 6.990157] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.997750] io scheduler noop registered [ 7.001797] io scheduler deadline registered [ 7.006193] io scheduler cfq registered (default) [ 7.012330] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 7.021611] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 7.030190] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 7.036544] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 7.043501] pci_bus 0000:00: root bus resource [bus 00-ff] [ 7.049363] PCI: bus0: Fast back to back transfers disabled [ 7.055041] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 7.063622] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 7.101221] PCI: bus1: Fast back to back transfers disabled [ 7.106949] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe5ffffff] [ 7.113910] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 7.120326] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe3ffffff pref] [ 7.127630] pci 0000:01:00.0: BAR 1: assigned [mem 0xe4000000-0xe403ffff] [ 7.134497] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x1007f] [ 7.140825] pci 0000:00:01.0: PCI bridge to [bus 01] [ 7.145871] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 7.152223] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe5ffffff] [ 7.159143] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 7.165844] mv_xor f1060800.xor: Marvell shared XOR driver [ 7.231894] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 7.239745] mv_xor f1060900.xor: Marvell shared XOR driver [ 7.301887] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 7.309952] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 7.317744] console [ttyS0] disabled [ 7.321515] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 27, base_baud = 12500000) is a 16550A [ 7.330554] console [ttyS0] enabled [ 7.330554] console [ttyS0] enabled [ 7.337683] bootconsole [earlycon0] disabled [ 7.337683] bootconsole [earlycon0] disabled [ 7.354768] loop: module loaded [ 7.358495] sata_mv f1080000.sata: slots 32 ports 2 [ 7.366214] scsi host0: sata_mv [ 7.369802] scsi host1: sata_mv [ 7.373264] ata1: SATA max UDMA/133 irq 35 [ 7.377380] ata2: SATA max UDMA/133 irq 35 [ 7.383109] m25p80 spi0.0: found mx25l8005, expected m25p80 [ 7.388722] m25p80 spi0.0: mx25l8005 (1024 Kbytes) [ 7.393626] 5 ofpart partitions found on MTD device spi0.0 [ 7.399135] Creating 5 MTD partitions on "spi0.0": [ 7.403978] 0x000000000000-0x000000080000 : "u-boot" [ 7.410298] 0x000000080000-0x0000000c0000 : "SSD firmware" [ 7.417162] 0x0000000c0000-0x0000000d0000 : "u-boot env" [ 7.423832] 0x0000000d0000-0x0000000e0000 : "permanent u-boot env" [ 7.431095] 0x0000000d0000-0x0000000e0000 : "permanent u-boot env" [ 7.439546] libphy: Fixed MDIO Bus: probed [ 7.444507] libphy: orion_mdio_bus: probed [ 7.453510] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 7.461703] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address f4:ce:46:23:fd:25 [ 7.470558] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.477208] ehci-pci: EHCI PCI platform driver [ 7.481812] ehci-orion: EHCI orion driver [ 7.486037] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.491635] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.499595] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000 [ 7.531190] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.537488] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.544339] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.551620] usb usb1: Product: EHCI Host Controller [ 7.556516] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 7.563267] usb usb1: SerialNumber: f1050000.ehci [ 7.568689] hub 1-0:1.0: USB hub found [ 7.572543] hub 1-0:1.0: 1 port detected [ 7.577144] usbcore: registered new interface driver usb-storage [ 7.583579] mousedev: PS/2 mouse device common for all mice [ 7.589772] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 7.596881] i2c /dev entries driver [ 7.602573] hidraw: raw HID events driver (C) Jiri Kosina [ 7.608430] drop_monitor: Initializing network drop monitor service [ 7.615036] NET: Registered protocol family 17 [ 7.619583] Key type dns_resolver registered [ 7.624707] registered taskstats version 1 [ 7.628820] Loading compiled-in X.509 certificates [ 7.633749] zswap: loaded using pool lzo/zbud [ 7.647864] Key type big_key registered [ 7.660981] Key type encrypted registered [ 7.666462] rtc-mv f1010300.rtc: setting system clock to 2008-09-10 21:44:14 UTC (1221083054) [ 7.881205] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.889807] ata1.00: ATA-7: SM224, I0521, max UDMA/133 [ 7.895004] ata1.00: 949536 sectors, multi 0: LBA [ 7.902249] ata1.00: configured for UDMA/133 [ 7.917091] scsi 0:0:0:0: Direct-Access ATA SM224 1 PQ: 0 ANSI: 5 [ 7.926314] sd 0:0:0:0: [sda] 949536 512-byte logical blocks: (486 MB/464 MiB) [ 7.933624] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 7.940989] sd 0:0:0:0: [sda] Write Protect is off [ 7.946004] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7.956938] sda: sda1 [ 7.960670] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.121742] usb 1-1: New USB device found, idVendor=0424, idProduct=2514 [ 8.128494] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 8.136420] hub 1-1:1.0: USB hub found [ 8.140357] hub 1-1:1.0: 4 ports detected [ 8.272749] ata2: SATA link down (SStatus 0 SControl F300) [ 8.291262] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 8.461256] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 8.633742] usb 1-1.3: New USB device found, idVendor=1307, idProduct=0165 [ 8.640681] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.660906] usb 1-1.3: Product: USB Mass Storage Device [ 8.671251] usb 1-1.3: Manufacturer: USBest Technology [ 8.676418] usb 1-1.3: SerialNumber: 1006296602673f [ 8.693955] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 8.708422] scsi host2: usb-storage 1-1.3:1.0 [ 9.181333] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. [ 9.772576] scsi 2:0:0:0: Direct-Access take MS Colorline 0.00 PQ: 0 ANSI: 2 [ 9.786925] sd 2:0:0:0: [sdb] 7613559 512-byte logical blocks: (3.90 GB/3.63 GiB) [ 9.800918] sd 2:0:0:0: [sdb] Write Protect is off [ 9.811541] sd 2:0:0:0: [sdb] Asking for cache data failed [ 9.817083] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 9.953613] sdb: sdb1 [ 9.962657] sd 2:0:0:0: [sdb] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping root file system [ 19.301437] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem [ 19.320290] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [....] Synthesizing the initial hotplug events...[ 21.296438] input: gpio_keys as /devices/platform/gpio_keys/input/input0 done. [....] Waiting for /dev to be fully populated...[ 21.540949] xgifb: module is from the staging directory, the quality is unknown, you have been warned. [ 21.634644] xgifb 0000:01:00.0: Relocate IO address: 10000 [00010030] [ 21.716819] xgifb 0000:01:00.0: chipid = 32 [ 21.729215] xgifb: SR14=51 DramSzie 2000000 ChannelNum 1 [ 21.775211] xgifb 0000:01:00.0: Framebuffer at 0xe0000000, mapped to 0xd1000000, size 32768k [ 21.823950] marvell-cesa f1030000.crypto: CESA device successfully registered [ 21.825149] orion_wdt: Initial timeout 21 sec [ 21.860553] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 21.860773] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 22.035665] xgifb 0000:01:00.0: MMIO at 0xe4000000, mapped to 0xd0f00000, size 256k [ 22.073545] asoc-simple-card sound: alc5621-hifi <-> i2s mapping ok [ 22.187251] xgifb 0000:01:00.0: No or unknown bridge type detected [ 22.207513] xgifb: Default mode is 800x600x16 (60Hz) [ 22.319389] random: crng init done done. [ ok ] Activating swap:. [ 23.262879] EXT4-fs (sdb1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sdb1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 9256/238080 files, 109010/951296 blocks . ok [ 23.504326] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 26.885230] NET: Registered protocol family 10 [ 26.892180] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 26.898226] Segment Routing with IPv6 [....] Configuring network interfaces...[ 30.158663] Unable to handle kernel paging request at virtual address 6961775e [ 30.165922] pgd = cfa18000 [ 30.168642] [6961775%] *pgd=00000000 [ 30.172241] Internal error: Oops: 80000005 [#1] PREEMPT ARM [ 30.177833] Modules linked in: ipv6 evdev snd_soc_simple_card snd_soc_simple_card_utils snd_soc_kirkwood snd_soc_alc5623 sg snd_soc_core snd_pcm_dmaengine snd_pcm orion_wdt marvell_cesa snd_timer snd soundc/re ac97_bus xgifb(C) cfbfillrect cfbimgblt cfbcopyarea fb uio_pdrv_genirq uio gpio_keys uas fixed