Welcome! Log In Create A New Profile

Advanced

RN10400

Posted by AkkJaa 
Re: RN10400
May 21, 2021 09:30PM
Hi Bodhi,

Here is a new readout. It look like there is no files inside the dir.

BootROM 1.08
Booting from NAND flash


General initialization - Version: 1.0.0

High speed PHY - Version: 2.1.4 (COM-PHY-V20) 
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully 
BootROM: Image checksum verification PASSED

 __   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_ 
        | | | |___|  _ \ / _ \ / _ \| __| 
        | |_| |___| |_) | (_) | (_) | |_ 
         \___/    |____/ \___/ \___/ \__| 
 ** LOADER **


U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1 
06/23/2015 ReadyNAS-104 V2.0

Board: DB-88F6710-BP
SoC:   MV6710 A1
CPU:   Marvell PJ4B v7 UP (Rev 1) LE
       CPU    @ 1200 [MHz]
       L2     @ 600 [MHz]
       TClock @ 200 [MHz]
       DDR    @ 600 [MHz]
       DDR 16Bit Width, FastPath Memory Access
DRAM:  512 MiB

Map:   Code:		0x1feef000:0x1ff9f514
       BSS:		0x1ffef8a0
       Stack:		0x1f9eeef8
       Heap:		0x1f9ef000:0x1feef000

NAND:  (ID 0xf12c)	128 MiB
MMC:   MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01

Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
       SDIO
       AUDIO
       TDM
Modules/Interfaces Detected:
       RGMII0 Phy
       RGMII1 Phy
       PEX0 (Lane 0)
       PEX1 (Lane 1)
       SATA0 (Lane 2)
       SATA1 (Lane 3)
Net:   egiga0, egiga1 [PRIME]
Power On!

FDT loaded successfully
Delay 7s then power on another group of HDDs 1 
Hit any key to stop autoboot:  0 
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start;fatload usb 0:1 0x2000000 /uImage-recovery;fatload usb 0:1 0x3000000 /initrd-recovery.gz;nand read 0x1000000 0xD4000 0x6000; bootm 0x2000000 0x3000000 0x1000000
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=yes
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x2000000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x3000000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
test_xxxx=yes
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=run load_uimage; if run load_uinitrd; then bootm 0x2000000 0x3000000; else bootm 0x2000000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81

Environment size: 2749/131068 bytes
Marvell>> setenv mtdparts 'mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)' 
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' 
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x2000000 /boot/uImage' 
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x3000000 /boot/uInitrd' 
Marvell>> setenv usb_boot 'run load_uimage; if run load_uinitrd; then bootm 0x2000000 0x3000000; else bootm 0x2000000; fi' 
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' 
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset' 
Marvell>> setenv fdt_skip_update yes
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...
Writing to Nand... done
Marvell>> boot
(Re)start USB...
USB:   Active port:	0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
5419270 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9504816 bytes read
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Linux-5.8.5-mvebu-370xp-tld-1
   Created:      2021-03-23  17:16:36 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5419206 Bytes = 5.2 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
   Image Name:   initramfs-5.8.5-mvebu-370xp-tld-
   Created:      2021-03-23  17:17:43 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9504752 Bytes = 9.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 5.8.5-mvebu-370xp-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1.0 SMP PREEMPT Mon Aug 31 00:00:32 PDT 2020
[    0.000000][    T0] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d
[    0.000000][    T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: NETGEAR ReadyNAS 104
[    0.000000][    T0] printk: bootconsole [earlycon0] enabled
[    0.000000][    T0] Memory policy: Data cache writeback
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x000000001fffffff]
[    0.000000][    T0]   HighMem  empty
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x000000001fffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[    0.000000][    T0] CPU: All CPU(s) started in SVC mode.
[    0.000000][    T0] percpu: Embedded 20 pages/cpu s53068 r8192 d20660 u81920
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 130048
[    0.000000][    T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) earlyprintk=serial mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) reason=normal bdtype=rn104
[    0.000000][    T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 493604K/524288K available (10240K kernel code, 1012K rwdata, 3072K rodata, 1024K init, 342K bss, 30684K reserved, 0K cma-reserved, 0K highmem)
[    0.000000][    T0] random: get_random_u32 called from ____cache_alloc+0x338/0x794 with crng_init=0
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0] rcu: 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000][    T0] 	Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0] 	Rude variant of Tasks RCU enabled.
[    0.000000][    T0] 	Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] L2C: DT/platform modifies aux control register: 0x12086300 -> 0x1a086302
[    0.000000][    T0] Aurora cache controller enabled, 4 ways, 256 kB
[    0.000000][    T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302
[    0.000000][    T0] Switching to timer-based delay loop, resolution 53ns
[    0.000007][    T0] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114537122277ns
[    0.007874][    T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101938038664 ns
[    0.019304][    T0] Console: colour dummy device 80x30
[    0.024022][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 37.49 BogoMIPS (lpj=187492)
[    0.034152][    T0] pid_max: default: 32768 minimum: 301
[    0.039217][    T0] LSM: Security Framework initializing
[    0.044164][    T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.051492][    T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.060288][    T0] CPU: Testing write buffer coherency: ok
[    0.065725][    T1] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.072052][    T1] Setting up static identity map for 0x100000 - 0x100060
[    0.078744][    T1] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1
[    0.084177][    T1] mvebu-pmsu: Initializing Power Management Service Unit
[    0.090702][    T1] rcu: Hierarchical SRCU implementation.
[    0.098522][    T1] smp: Bringing up secondary CPUs ...
[    0.103411][    T1] smp: Brought up 1 node, 1 CPU
[    0.107708][    T1] SMP: Total of 1 processors activated (37.49 BogoMIPS).
[    0.114026][    T1] CPU: All CPU(s) started in SVC mode.
[    0.119565][    T1] devtmpfs: initialized
[    0.128263][    T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[    0.137177][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.146950][    T1] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.154159][    T1] xor: measuring software checksum speed
[    0.258575][    T1]    arm4regs  :  1103.200 MB/sec
[    0.358572][    T1]    8regs     :   671.200 MB/sec
[    0.458567][    T1]    32regs    :  1062.400 MB/sec
[    0.463020][    T1] xor: using function: arm4regs (1103.200 MB/sec)
[    0.468785][    T1] prandom: seed boundary self test passed
[    0.477388][    T1] prandom: 100 self tests passed
[    0.481802][    T1] pinctrl core: initialized pinctrl subsystem
[    0.488940][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.489691][    T1] NET: Registered protocol family 16
[    0.502536][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.510417][    T1] audit: initializing netlink subsys (disabled)
[    0.516395][   T31] audit: type=2000 audit(0.490:1): state=initialized audit_enabled=0 res=1
[    0.526660][    T1] cpuidle: using governor ladder
[    0.532679][    T1] cpuidle: using governor menu
[    0.537170][    T1] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.809605][    T1] raid6: int32x8  gen()   214 MB/s
[    0.979031][    T1] raid6: int32x8  xor()   135 MB/s
[    1.148653][    T1] raid6: int32x4  gen()   224 MB/s
[    1.318719][    T1] raid6: int32x4  xor()   151 MB/s
[    1.488571][    T1] raid6: int32x2  gen()   414 MB/s
[    1.658569][    T1] raid6: int32x2  xor()   217 MB/s
[    1.828549][    T1] raid6: int32x1  gen()   430 MB/s
[    1.998589][    T1] raid6: int32x1  xor()   201 MB/s
[    2.003120][    T1] raid6: using algorithm int32x1 gen() 430 MB/s
[    2.008693][    T1] raid6: .... xor() 201 MB/s, rmw enabled
[    2.013778][    T1] raid6: using intx1 recovery algorithm
[    2.020114][    T1] vgaarb: loaded
[    2.025066][    T1] SCSI subsystem initialized
[    2.030336][    T1] usbcore: registered new interface driver usbfs
[    2.036035][    T1] usbcore: registered new interface driver hub
[    2.043238][    T1] usbcore: registered new device driver usb
[    2.049936][    T1] mc: Linux media interface: v0.10
[    2.055354][    T1] videodev: Linux video capture interface: v2.00
[    2.061864][    T1] pps_core: LinuxPPS API ver. 1 registered
[    2.067033][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.076773][    T1] PTP clock support registered
[    2.084578][    T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[    3.073682][    T1] VFS: Disk quotas dquot_6.6.0
[    3.078066][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    3.115534][    T1] NET: Registered protocol family 2
[    3.121472][    T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    3.130229][    T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    3.138194][    T1] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    3.145477][    T1] TCP: Hash tables configured (established 4096 bind 4096)
[    3.152472][    T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    3.159282][    T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    3.166522][    T1] NET: Registered protocol family 1
[    3.171895][    T1] RPC: Registered named UNIX socket transport module.
[    3.178035][    T1] RPC: Registered udp transport module.
[    3.182963][    T1] RPC: Registered tcp transport module.
[    3.187910][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    3.194428][    T1] PCI: CLS 0 bytes, default 64
[    3.199041][    T1] Trying to unpack rootfs image as initramfs...
[    3.815559][    T1] Freeing initrd memory: 9284K
[    3.820062][    T1] NetWinder Floating Point Emulator V0.97 (double precision)
[    3.827037][    T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[    3.838023][    T1] Initialise system trusted keyrings
[    3.842760][    T1] Key type blacklist registered
[    3.849340][    T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    3.856176][    T1] zbud: loaded
[    3.860776][    T1] NFS: Registering the id_resolver key type
[    3.866500][    T1] Key type id_resolver registered
[    3.870957][    T1] Key type id_legacy registered
[    3.875390][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    3.882151][    T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    3.889028][    T1] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    3.897306][    T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[    3.904045][    T1] orangefs_init: module version upstream loaded
[    3.983992][    T1] async_tx: api initialized (async)
[    3.988696][    T1] Key type asymmetric registered
[    3.993071][    T1] Asymmetric key parser 'x509' registered
[    3.998420][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    4.006130][    T1] io scheduler bfq registered
[    4.013179][    T1] armada-370-pinctrl d0018000.pin-ctrl: registered pinctrl driver
[    4.030042][    T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[    4.037476][    T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[    4.043125][    T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[    4.050420][    T1] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    4.057096][    T1] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400
[    4.063249][    T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[    4.070662][    T1] pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400
[    4.077073][    T1] pci 0000:00:02.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[    4.085564][    T1] PCI: bus0: Fast back to back transfers disabled
[    4.091303][    T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    4.099355][    T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    4.107776][    T1] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[    4.113935][    T1] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x4000ffff 64bit]
[    4.121002][    T1] pci 0000:01:00.0: reg 0x18: [mem 0x40010000-0x40010fff 64bit]
[    4.127952][    T1] pci 0000:01:00.0: reg 0x20: [mem 0x40011000-0x40011fff 64bit]
[    4.134959][    T1] pci 0000:01:00.0: supports D1
[    4.139257][    T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[    4.146213][    T1] pci 0000:00:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[    4.185698][    T1] PCI: bus1: Fast back to back transfers disabled
[    4.191436][    T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    4.198551][    T1] pci 0000:02:00.0: [1b4b:9215] type 00 class 0x010601
[    4.204901][    T1] pci 0000:02:00.0: reg 0x10: [io  0xfffffff8-0xffffffff]
[    4.211267][    T1] pci 0000:02:00.0: reg 0x14: [io  0xfffffffc-0xffffffff]
[    4.217736][    T1] pci 0000:02:00.0: reg 0x18: [io  0xfffffff8-0xffffffff]
[    4.224101][    T1] pci 0000:02:00.0: reg 0x1c: [io  0xfffffffc-0xffffffff]
[    4.230545][    T1] pci 0000:02:00.0: reg 0x20: [io  0xffffffe0-0xffffffff]
[    4.236964][    T1] pci 0000:02:00.0: reg 0x24: [mem 0x42000000-0x420007ff]
[    4.243328][    T1] pci 0000:02:00.0: reg 0x30: [mem 0xd0000000-0xd000ffff pref]
[    4.250221][    T1] pci 0000:02:00.0: PME# supported from D3hot
[    4.256138][    T1] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[    4.295693][    T1] PCI: bus2: Fast back to back transfers disabled
[    4.301430][    T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    4.308253][    T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[    4.315227][    T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff]
[    4.322139][    T1] pci 0000:00:02.0: BAR 13: assigned [io  0x10000-0x10fff]
[    4.328625][    T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8200000-0xf82007ff pref]
[    4.335877][    T1] pci 0000:00:02.0: BAR 6: assigned [mem 0xf8300000-0xf83007ff pref]
[    4.343113][    T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf800ffff 64bit]
[    4.350451][    T1] pci 0000:01:00.0: BAR 2: assigned [mem 0xf8010000-0xf8010fff 64bit]
[    4.357785][    T1] pci 0000:01:00.0: BAR 4: assigned [mem 0xf8011000-0xf8011fff 64bit]
[    4.365116][    T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[    4.370290][    T1] pci 0000:00:01.0:   bridge window [mem 0xf8000000-0xf80fffff]
[    4.377150][    T1] pci 0000:02:00.0: BAR 6: assigned [mem 0xf8100000-0xf810ffff pref]
[    4.384380][    T1] pci 0000:02:00.0: BAR 5: assigned [mem 0xf8110000-0xf81107ff]
[    4.391234][    T1] pci 0000:02:00.0: BAR 4: assigned [io  0x10000-0x1001f]
[    4.397612][    T1] pci 0000:02:00.0: BAR 0: assigned [io  0x10020-0x10027]
[    4.403971][    T1] pci 0000:02:00.0: BAR 2: assigned [io  0x10028-0x1002f]
[    4.410348][    T1] pci 0000:02:00.0: BAR 1: assigned [io  0x10030-0x10033]
[    4.416724][    T1] pci 0000:02:00.0: BAR 3: assigned [io  0x10034-0x10037]
[    4.423084][    T1] pci 0000:00:02.0: PCI bridge to [bus 02]
[    4.428269][    T1] pci 0000:00:02.0:   bridge window [io  0x10000-0x10fff]
[    4.434644][    T1] pci 0000:00:02.0:   bridge window [mem 0xf8100000-0xf81fffff]
[    4.441597][    T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[    4.447941][    T1] pcieport 0000:00:02.0: enabling device (0140 -> 0143)
[    4.455478][    T1] mv_xor d0060800.xor: Marvell shared XOR driver
[    4.525972][    T1] mv_xor d0060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    4.536959][    T1] mv_xor d0060900.xor: Marvell shared XOR driver
[    4.605944][    T1] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    4.811353][    T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    4.822475][    T1] printk: console [ttyS0] disabled
[    4.848849][    T1] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 19, base_baud = 12500000) is a 16550A
[    4.857929][    T1] printk: console [ttyS0] enabled
[    4.857929][    T1] printk: console [ttyS0] enabled
[    4.866988][    T1] printk: bootconsole [earlycon0] disabled
[    4.866988][    T1] printk: bootconsole [earlycon0] disabled
[    4.879719][    T1] ahci 0000:02:00.0: enabling device (0146 -> 0147)
[    4.897042][    T1] ahci 0000:02:00.0: AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[    4.905241][    T1] ahci 0000:02:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs 
[    4.919483][    T1] scsi host0: ahci
[    4.924045][    T1] scsi host1: ahci
[    4.928625][    T1] scsi host2: ahci
[    4.933080][    T1] scsi host3: ahci
[    4.937187][    T1] ata1: SATA max UDMA/133 abar m2048@0xf8110000 port 0xf8110100 irq 42
[    4.945180][    T1] ata2: SATA max UDMA/133 abar m2048@0xf8110000 port 0xf8110180 irq 42
[    4.952641][    T1] ata3: SATA max UDMA/133 abar m2048@0xf8110000 port 0xf8110200 irq 42
[    4.960187][    T1] ata4: SATA max UDMA/133 abar m2048@0xf8110000 port 0xf8110280 irq 42
[    4.969572][    T1] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1
[    4.978027][    T1] nand: Micron MT29F1G08ABADAWP
[    4.982373][    T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    4.990729][    T1] Bad block table found at page 65472, version 0x01
[    4.997302][    T1] Bad block table found at page 65408, version 0x01
[    5.003567][    T1] 5 cmdlinepart partitions found on MTD device pxa3xx_nand-0
[    5.010384][    T1] Creating 5 MTD partitions on "pxa3xx_nand-0":
[    5.016061][    T1] 0x000000000000-0x000000180000 : "u-boot"
[    5.023537][    T1] 0x000000180000-0x0000001a0000 : "u-boot-env"
[    5.031906][    T1] 0x000000200000-0x000000800000 : "uImage"
[    5.039971][    T1] 0x000000800000-0x000000c00000 : "minirootfs"
[    5.048386][    T1] 0x000000c00000-0x000008000000 : "ubifs"
[    5.058177][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[    5.067339][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[    5.080639][    T1] libphy: Fixed MDIO Bus: probed
[    5.090229][    T1] libphy: orion_mdio_bus: probed
[    5.128154][    T1] mvneta d0070000.ethernet eth0: Using random mac address 76:a9:97:0a:cb:c0
[    5.142296][    T1] mvneta d0074000.ethernet eth1: Using random mac address d6:a3:31:d2:41:c8
[    5.153091][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.160632][    T1] ehci-pci: EHCI PCI platform driver
[    5.165927][    T1] ehci-orion: EHCI orion driver
[    5.170497][    T1] orion-ehci d0050000.usb: EHCI Host Controller
[    5.176527][    T1] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1
[    5.184381][    T1] orion-ehci d0050000.usb: irq 25, io mem 0xd0050000
[    5.214629][    T1] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00
[    5.221133][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    5.229515][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.236913][    T1] usb usb1: Product: EHCI Host Controller
[    5.242115][    T1] usb usb1: Manufacturer: Linux 5.8.5-mvebu-370xp-tld-1 ehci_hcd
[    5.249167][    T1] usb usb1: SerialNumber: d0050000.usb
[    5.255216][    T1] hub 1-0:1.0: USB hub found
[    5.259744][    T1] hub 1-0:1.0: 1 port detected
[    5.265602][    T1] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    5.271647][    T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    5.280083][    T1] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[    5.290221][    T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    5.298637][    T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.306042][    T1] usb usb2: Product: xHCI Host Controller
[    5.311210][    T1] usb usb2: Manufacturer: Linux 5.8.5-mvebu-370xp-tld-1 xhci-hcd
[    5.318227][    T1] usb usb2: SerialNumber: 0000:01:00.0
[    5.324098][    T1] hub 2-0:1.0: USB hub found
[    5.328604][    T1] hub 2-0:1.0: 2 ports detected
[    5.334002][    T1] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    5.339885][    T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[    5.347490][    T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    5.354011][    T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.362419][    T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[    5.370935][    T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.378342][    T1] usb usb3: Product: xHCI Host Controller
[    5.383522][    T1] usb usb3: Manufacturer: Linux 5.8.5-mvebu-370xp-tld-1 xhci-hcd
[    5.390544][    T1] usb usb3: SerialNumber: 0000:01:00.0
[    5.396393][    T1] hub 3-0:1.0: USB hub found
[    5.400806][    T1] hub 3-0:1.0: 2 ports detected
[    5.406964][    T1] usbcore: registered new interface driver usblp
[    5.413574][    T1] usbcore: registered new interface driver usb-storage
[    5.420737][    T1] mousedev: PS/2 mouse device common for all mice
[    5.428580][    T1] i2c /dev entries driver
[    5.437492][    T1] rtc-ds1307 0-0068: 'wakeup-source' is set, request for an IRQ is disabled!
[    5.450601][    T1] rtc-ds1307 0-0068: registered as rtc0
[    5.457310][    T1] rtc-ds1307 0-0068: setting system clock to 2000-02-17T17:22:40 UTC (950808160)
[    5.466573][    T1] pca953x 0-0023: supply vcc not found, using dummy regulator
[    5.473403][    T1] pca953x 0-0023: using no AI
[    5.484680][ T1212] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    5.506312][    T1] orion_wdt: Initial timeout 229 sec
[    5.512763][    T1] device-mapper: uevent: version 1.0.3
[    5.518800][    T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com
[    5.528096][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    5.534974][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    5.541713][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    5.548619][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    5.555091][    T1] device-mapper: raid: Loading target version 1.15.1
[    5.575719][    T1] marvell-cesa d0090000.crypto: CESA device successfully registered
[    5.585056][    T1] hid: raw HID events driver (C) Jiri Kosina
[    5.592827][    T1] usbcore: registered new interface driver usbhid
[    5.599924][    T1] usbhid: USB HID core driver
[    5.605776][    T1] drop_monitor: Initializing network drop monitor service
[    5.613609][    T1] NET: Registered protocol family 10
[    5.621023][    T1] Segment Routing with IPv6
[    5.625250][   T20] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    5.632436][    T1] RPL Segment Routing with IPv6
[    5.637239][    T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    5.647802][    T1] NET: Registered protocol family 17
[    5.653995][    T1] 8021q: 802.1Q VLAN Support v1.8
[    5.658870][    T1] Key type dns_resolver registered
[    5.663749][    T1] ThumbEE CPU extension supported.
[    5.668603][    T1] Registering SWP/SWPB emulation handler
[    5.674459][    T1] registered taskstats version 1
[    5.679538][    T1] Loading compiled-in X.509 certificates
[    5.685119][    T1] zswap: loaded using pool lzo/zbud
[    5.690553][    T1] Key type ._fscrypt registered
[    5.695192][    T1] Key type .fscrypt registered
[    5.699463][    T1] Key type fscrypt-provisioning registered
[    5.708079][    T1] Key type big_key registered
[    5.752917][    T1] Key type encrypted registered
[    5.763631][    T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    5.838106][   T20] usb 1-1: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00
[    5.846452][   T20] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.853731][   T20] usb 1-1: Product: USB DISK 2.0
[    5.858208][   T20] usb 1-1: Manufacturer:         
[    5.862710][   T20] usb 1-1: SerialNumber: 9000996E0B7F4964
[    5.869575][   T20] usb-storage 1-1:1.0: USB Mass Storage device detected
[    5.877569][   T20] scsi host4: usb-storage 1-1:1.0
[    5.910219][ T1212] ata4.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133
[    5.917419][ T1212] ata4.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[    5.929443][ T1212] ata4.00: configured for UDMA/133
[    6.104914][ T1204] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    6.111356][ T1200] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    6.144678][ T1204] ata2.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133
[    6.151513][ T1204] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[    6.158902][ T1200] ata1.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133
[    6.165855][ T1200] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[    6.173432][ T1204] ata2.00: configured for UDMA/133
[    6.178832][ T1200] ata1.00: configured for UDMA/133
[    6.194522][  T187] scsi 0:0:0:0: Direct-Access     ATA      WDC WD30EZRX-00M 0A80 PQ: 0 ANSI: 5
[    6.206262][ T1218] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[    6.214059][ T1218] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    6.221098][    T7] scsi 1:0:0:0: Direct-Access     ATA      WDC WD30EZRX-00M 0A80 PQ: 0 ANSI: 5
[    6.234329][ T1483] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[    6.244905][ T1218] sd 0:0:0:0: [sda] Write Protect is off
[    6.250196][ T1483] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    6.256232][ T1218] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.265615][ T1483] sd 1:0:0:0: [sdb] Write Protect is off
[    6.271019][ T1483] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.321402][ T1218]  sda: sda1 sda2 sda3
[    6.326345][ T1483]  sdb: sdb1 sdb2 sdb3
[    6.334747][ T1208] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    6.345027][ T1218] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    6.354304][ T1483] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[    6.380249][ T1208] ata3.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133
[    6.387426][ T1208] ata3.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[    6.400018][ T1208] ata3.00: configured for UDMA/133
[    6.415717][   T15] scsi 2:0:0:0: Direct-Access     ATA      WDC WD30EZRX-00M 0A80 PQ: 0 ANSI: 5
[    6.427242][ T1483] sd 2:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[    6.437025][ T1216] scsi 3:0:0:0: Direct-Access     ATA      WDC WD30EZRX-00M 0A80 PQ: 0 ANSI: 5
[    6.446368][ T1483] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[    6.455535][   T15] sd 3:0:0:0: [sdd] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[    6.463332][   T15] sd 3:0:0:0: [sdd] 4096-byte physical blocks
[    6.471194][ T1483] sd 2:0:0:0: [sdc] Write Protect is off
[    6.476965][ T1483] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.486539][   T15] sd 3:0:0:0: [sdd] Write Protect is off
[    6.491951][   T15] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.548380][   T15]  sdd: sdd1 sdd2 sdd3
[    6.553250][ T1483]  sdc: sdc1 sdc2 sdc3
[    6.563664][   T15] sd 3:0:0:0: [sdd] Attached SCSI removable disk
[    6.575201][ T1483] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[    6.584020][    T1] Freeing unused kernel memory: 1024K
[    6.606895][    T1] Checked W+X mappings: passed, no W+X pages found
[    6.612797][    T1] Run /init as init process
Loading, please wait...
Starting version 241
[    6.906990][ T1483] scsi 4:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 4
[    6.932845][   T15] sd 4:0:0:0: [sde] 30322688 512-byte logical blocks: (15.5 GB/14.5 GiB)
[    6.959016][    C0] random: fast init done
[    6.963434][   T15] sd 4:0:0:0: [sde] Write Protect is off
[    6.975726][   T15] sd 4:0:0:0: [sde] No Caching mode page found
[    6.981289][   T15] sd 4:0:0:0: [sde] Assuming drive cache: write through
[    7.022183][   T15]  sde: sde1
[    7.044894][   T15] sd 4:0:0:0: [sde] Attached SCSI removable disk
[    9.849014][ T1554] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[   24.005908][ T1571] process '/usr/bin/fstype' started with executable stack
[   24.016488][    C0] random: crng init done
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /dev/sde1] fsck.ext3 -a -C0 /dev/sde1 
rootfs: recovering journal
rootfs: clean, 27085/948416 files, 402442/3790323 blocks
done.
[   80.239452][ T1580] EXT4-fs (sde1): mounting ext3 file system using the ext4 subsystem
[   80.279992][ T1580] EXT4-fs (sde1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[   86.741559][ T1774] systemd-udevd[1774]: Using default interface naming scheme 'v240'.
[   86.846560][ T1774] systemd-udevd[1774]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   86.915544][ T1773] systemd-udevd[1773]: Using default interface naming scheme 'v240'.
[   86.924035][ T1773] systemd-udevd[1773]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   87.015592][ T1774] systemd-udevd[1774]: Could not generate persistent MAC address for eth0: No such file or directory
[   87.124293][ T1773] systemd-udevd[1773]: Could not generate persistent MAC address for eth1: No such file or directory
[   87.234204][ T1775] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   87.294234][ T1775] sd 1:0:0:0: Attached scsi generic sg1 type 0
[   87.358919][ T1775] sd 2:0:0:0: Attached scsi generic sg2 type 0
[   87.446478][ T1775] sd 3:0:0:0: Attached scsi generic sg3 type 0
[   87.547282][ T1775] sd 4:0:0:0: Attached scsi generic sg4 type 0
[   89.547769][ T1791] systemd-udevd[1791]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   89.563250][ T1792] systemd-udevd[1792]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   89.578469][ T1794] systemd-udevd[1794]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   89.653639][ T1791] systemd-udevd[1791]: Could not generate persistent MAC address for ip6tnl0: No such file or directory
[   89.734898][ T1844] md/raid1:md0: active with 4 out of 4 mirrors
[   89.766539][ T1844] md0: detected capacity change from 0 to 4290772992
[   89.856267][ T1845] md/raid:md1: device sdd2 operational as raid disk 3
[   89.862385][ T1845] md/raid:md1: device sdc2 operational as raid disk 2
[   90.024775][ T1845] md/raid:md1: device sdb2 operational as raid disk 1
[   90.030889][ T1845] md/raid:md1: device sda2 operational as raid disk 0
[   90.038033][ T1846] md/raid:md127: device sdd3 operational as raid disk 3
[   90.044307][ T1846] md/raid:md127: device sdc3 operational as raid disk 2
[   90.174757][ T1846] md/raid:md127: device sdb3 operational as raid disk 1
[   90.181033][ T1846] md/raid:md127: device sda3 operational as raid disk 0
[   90.254918][ T1845] md/raid:md1: raid level 6 active with 4 out of 4 devices, algorithm 2
[   90.334850][ T1845] md1: detected capacity change from 0 to 1072562176
[   90.381498][ T1846] md/raid:md127: raid level 5 active with 4 out of 4 devices, algorithm 2
[   90.449915][ T1846] md127: detected capacity change from 0 to 8986874216448
[   94.164983][ T1871] Btrfs loaded, crc32c=crc32c-generic
[   94.177017][ T1791] BTRFS: device label 2fe534ca:data devid 1 transid 96273 /dev/md127 scanned by systemd-udevd (1791)
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[   97.147176][ T2024] EXT4-fs (sde1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

[  108.793985][ T2555] mvneta d0070000.ethernet eth0: PHY [d0072004.mdio-mii:00] driver [Marvell 88E1318S] (irq=POLL)
[  108.804074][ T2555] mvneta d0070000.ethernet eth0: configuring for phy/rgmii-id link mode
Listening on LPF/eth0/76:a9:97:0a:cb:c0
Sending on   LPF/eth0/76:a9:97:0a:cb:c0
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
[  112.985522][ T1865] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[  112.993587][ T1865] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPOFFER of 192.168.0.186 from 192.168.0.1
DHCPREQUEST for 192.168.0.186 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.0.186 from 192.168.0.1
bound to 192.168.0.186 -- renewal in 2923 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2792 (syslogd)
. ok 
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2819 (klogd)
. ok 
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting MD monitoring service: mdadm --monitor.
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Running local boot scripts (/etc/rc.local)[  133.758251][ T3052] Setting Persistent MAC address to E8:FC:AF:E5:34:CA
<13>Feb 17 09:24:56 root[3059]: Setting Persistent MAC address to E8:FC:AF:E5:34:CA
Killed old client process
Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/76:a9:97:0a:cb:c0
Sending on   LPF/eth0/76:a9:97:0a:cb:c0
Sending on   Socket/fallback
DHCPRELEASE of 192.168.0.186 on eth0 to 192.168.0.1 port 67
[  135.051944][    T5] mvneta d0070000.ethernet eth0: Link is Down
Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

[  135.441509][ T3096] mvneta d0070000.ethernet eth0: PHY [d0072004.mdio-mii:00] driver [Marvell 88E1318S] (irq=POLL)
[  135.451570][ T3096] mvneta d0070000.ethernet eth0: configuring for phy/rgmii-id link mode
Listening on LPF/eth0/e8:fc:af:e5:34:ca
Sending on   LPF/eth0/e8:fc:af:e5:34:ca
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
[  138.588209][    T5] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[  138.596274][    T5] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19
DHCPOFFER of 192.168.0.186 from 192.168.0.1
DHCPREQUEST for 192.168.0.186 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.0.186 from 192.168.0.1
bound to 192.168.0.186 -- renewal in 3293 seconds.
. ok 

Debian GNU/Linux 10 debian ttyS0

debian login: root
Password: 
Last login: Thu Feb 17 05:38:49 PST 2000 on ttyS0
Linux debian 5.8.5-mvebu-370xp-tld-1 #1.0 SMP PREEMPT Mon Aug 31 00:00:32 PDT 2020 armv7l

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
debian
192.168.0.186
NETGEAR ReadyNAS 104
Linux version 5.8.5-mvebu-370xp-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1.0 SMP PREEMPT Mon Aug 31 00:00:32 PDT 2020
Debian 10.0
Thu Feb 17 09:25:27 PST 2000 up 2 minutes
root@debian:~# ls -l /tmp/md0_data
ls: cannot access '/tmp/md0_data': No such file or directory
root@debian:~# mount /dev/md0  /tmp/md0_data
mount: /tmp/md0_data: mount point does not exist.
root@debian:~# mkdir -p /tmp/md0_data
root@debian:~# mount /dev/md0  /tmp/md0_data
[  326.186107][ T3189] EXT4-fs (md0): recovery complete
[  326.200954][ T3189] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
root@debian:~# mkdir -p /tmp/md1_data
root@debian:~# mkdir -p /tmp/md127_data
root@debian:~# mount /dev/md1  /tmp/md1_data
mount: /tmp/md1_data: unknown filesystem type 'swap'.
root@debian:~# mount /dev/md127 /tmp/md127_data
[  397.357978][ T3196] BTRFS info (device md127): disk space caching is enabled
[  397.364500][ T3196] BTRFS info (device md127): has skinny extents
root@debian:~# ls -l /tmp/md0_data
total 112
drwxr-xr-x 25 root root  4096 Jun 10  2018 .
drwxrwxrwt  5 root root   100 Feb 17 09:28 ..
-rw-------  1 root root  1024 Aug 12  2016 .rnd
drwxr-xr-x  2 root root  4096 Aug 12  2016 apps
drwxr-xr-x  2 root root  4096 Aug 12  2016 bin
drwxr-xr-x  2 root root  4096 Jun 17  2012 boot
drwxrwxrwt  2 root root  4096 Aug 12  2016 data
drwxr-xr-x  4 root root  4096 Aug 12  2016 dev
drwxr-xr-x 73 root root  4096 Jun 11  2018 etc
drwxr-xr-x  6 root root  4096 Aug 12  2016 frontview
-rw-r--r--  1 root root     0 Jun 10  2018 ftp_ban.tbl
drwxr-xr-x  2 root root  4096 Jun 17  2012 home
drwxr-xr-x 14 root root  4096 Aug 12  2016 lib
drwx------  2 root root 16384 Aug 12  2016 lost+found
drwxr-xr-x  2 root root  4096 Nov 17  2012 media
drwxr-xr-x  2 root root  4096 Jun 17  2012 mnt
drwxr-xr-x  9 root root  4096 Aug 12  2016 opt
drwxr-xr-x  2 root root  4096 Jun 17  2012 proc
drwx------  3 root root  4096 Aug 12  2016 root
drwxr-xr-x  2 root root  4096 Jun  3  2016 run
drwxr-xr-x  2 root root  4096 Aug 12  2016 sbin
drwxr-xr-x  2 root root  4096 Jun 10  2012 selinux
drwxr-xr-x  2 root root  4096 Nov 17  2012 srv
drwxr-xr-x  2 root root  4096 Feb  7  2013 sys
drwxrwxrwt  7 root root  4096 Dec 22  2019 tmp
drwxr-xr-x 10 root root  4096 Aug 12  2016 usr
drwxr-xr-x 17 root root  4096 Aug 12  2016 var
root@debian:~# ls -l /tmp/md1_data
total 0
drwxr-xr-x 2 root root  40 Feb 17 09:28 .
drwxrwxrwt 5 root root 100 Feb 17 09:28 ..
root@debian:~# ls -l /tmp/md127_data
total 32
drwxr-xr-x  1 root root 140 Aug 12  2016 .
drwxrwxrwt  5 root root 100 Feb 17 09:28 ..
drwxr-xr-x  1 root root 102 Aug 25  2019 ._share
drwxrwxrwx  1 root root  90 Aug 25  2019 .apps
drwxr-xr-x  1 root root   0 Aug 12  2016 .timemachine
drwxr-xr-x  1 root root   0 Aug 12  2016 .vault
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 Documents
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 Music
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 Pictures
drwxrwxrwx+ 1   99   99 430 Oct 29  2019 Readynas
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 Videos
drwxr-xr-x  1   98   98  22 Aug 12  2016 home
root@debian:~# ls -lR  /tmp/md127_data/Music
/tmp/md127_data/Music:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Music/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~# ls -lR  /tmp/md127_data/videos
ls: cannot access '/tmp/md127_data/videos': No such file or directory
root@debian:~# ls -lR  /tmp/md127_data/Videos
/tmp/md127_data/Videos:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Videos/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~# ls -lR  /tmp/md127_data/Documents
/tmp/md127_data/Documents:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Documents/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~# ls -lR  /tmp/md127_data/Pictures
/tmp/md127_data/Pictures:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Pictures/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~#

Or do i do something wrong here.

Thanks again.

Best regards.

AkkJaa...
Re: RN10400
May 21, 2021 09:52PM
Bodhi,

Look like it is empty. Or i can't get into it.
NETGEAR ReadyNAS 104
Linux version 5.8.5-mvebu-370xp-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1.0 SMP PREEMPT Mon Aug 31 00:00:32 PDT 2020
Debian 10.0
Thu Feb 17 09:25:27 PST 2000 up 2 minutes
root@debian:~# ls -l /tmp/md0_data
ls: cannot access '/tmp/md0_data': No such file or directory
root@debian:~# mount /dev/md0  /tmp/md0_data
mount: /tmp/md0_data: mount point does not exist.
root@debian:~# mkdir -p /tmp/md0_data
root@debian:~# mount /dev/md0  /tmp/md0_data
[  326.186107][ T3189] EXT4-fs (md0): recovery complete
[  326.200954][ T3189] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
root@debian:~# mkdir -p /tmp/md1_data
root@debian:~# mkdir -p /tmp/md127_data
root@debian:~# mount /dev/md1  /tmp/md1_data
mount: /tmp/md1_data: unknown filesystem type 'swap'.
root@debian:~# mount /dev/md127 /tmp/md127_data
[  397.357978][ T3196] BTRFS info (device md127): disk space caching is enabled
[  397.364500][ T3196] BTRFS info (device md127): has skinny extents
root@debian:~# ls -l /tmp/md0_data
total 112
drwxr-xr-x 25 root root  4096 Jun 10  2018 .
drwxrwxrwt  5 root root   100 Feb 17 09:28 ..
-rw-------  1 root root  1024 Aug 12  2016 .rnd
drwxr-xr-x  2 root root  4096 Aug 12  2016 apps
drwxr-xr-x  2 root root  4096 Aug 12  2016 bin
drwxr-xr-x  2 root root  4096 Jun 17  2012 boot
drwxrwxrwt  2 root root  4096 Aug 12  2016 data
drwxr-xr-x  4 root root  4096 Aug 12  2016 dev
drwxr-xr-x 73 root root  4096 Jun 11  2018 etc
drwxr-xr-x  6 root root  4096 Aug 12  2016 frontview
-rw-r--r--  1 root root     0 Jun 10  2018 ftp_ban.tbl
drwxr-xr-x  2 root root  4096 Jun 17  2012 home
drwxr-xr-x 14 root root  4096 Aug 12  2016 lib
drwx------  2 root root 16384 Aug 12  2016 lost+found
drwxr-xr-x  2 root root  4096 Nov 17  2012 media
drwxr-xr-x  2 root root  4096 Jun 17  2012 mnt
drwxr-xr-x  9 root root  4096 Aug 12  2016 opt
drwxr-xr-x  2 root root  4096 Jun 17  2012 proc
drwx------  3 root root  4096 Aug 12  2016 root
drwxr-xr-x  2 root root  4096 Jun  3  2016 run
drwxr-xr-x  2 root root  4096 Aug 12  2016 sbin
drwxr-xr-x  2 root root  4096 Jun 10  2012 selinux
drwxr-xr-x  2 root root  4096 Nov 17  2012 srv
drwxr-xr-x  2 root root  4096 Feb  7  2013 sys
drwxrwxrwt  7 root root  4096 Dec 22  2019 tmp
drwxr-xr-x 10 root root  4096 Aug 12  2016 usr
drwxr-xr-x 17 root root  4096 Aug 12  2016 var
root@debian:~# ls -l /tmp/md1_data
total 0
drwxr-xr-x 2 root root  40 Feb 17 09:28 .
drwxrwxrwt 5 root root 100 Feb 17 09:28 ..
root@debian:~# ls -l /tmp/md127_data
total 32
drwxr-xr-x  1 root root 140 Aug 12  2016 .
drwxrwxrwt  5 root root 100 Feb 17 09:28 ..
drwxr-xr-x  1 root root 102 Aug 25  2019 ._share
drwxrwxrwx  1 root root  90 Aug 25  2019 .apps
drwxr-xr-x  1 root root   0 Aug 12  2016 .timemachine
drwxr-xr-x  1 root root   0 Aug 12  2016 .vault
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 Documents
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 Music
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 Pictures
drwxrwxrwx+ 1   99   99 430 Oct 29  2019 Readynas
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 Videos
drwxr-xr-x  1   98   98  22 Aug 12  2016 home
root@debian:~# ls -lR  /tmp/md127_data/Music
/tmp/md127_data/Music:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Music/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~# ls -lR  /tmp/md127_data/videos
ls: cannot access '/tmp/md127_data/videos': No such file or directory
root@debian:~# ls -lR  /tmp/md127_data/Videos
/tmp/md127_data/Videos:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Videos/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~# ls -lR  /tmp/md127_data/Documents
/tmp/md127_data/Documents:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Documents/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~# ls -lR  /tmp/md127_data/Pictures
/tmp/md127_data/Pictures:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Pictures/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~# ls -l /tmp/md0_data/media
total 8
drwxr-xr-x  2 root root 4096 Nov 17  2012 .
drwxr-xr-x 25 root root 4096 Jun 10  2018 ..
root@debian:~# ls -l /tmp/md0_data/dev
total 16
drwxr-xr-x  4 root root  4096 Aug 12  2016 .
drwxr-xr-x 25 root root  4096 Jun 10  2018 ..
crw-------  1 root tty  5,  1 Nov  6  2012 console
lrwxrwxrwx  1 root root    11 Aug 12  2016 core -> /proc/kcore
lrwxrwxrwx  1 root root    13 Aug 12  2016 fd -> /proc/self/fd
crw-rw-rw-  1 root root 1,  7 Nov  6  2012 full
crw-r-----  1 root kmem 1,  2 Nov  6  2012 kmem
brw-rw----  1 root disk 7,  0 Nov  6  2012 loop0
brw-rw----  1 root disk 7,  1 Nov  6  2012 loop1
brw-rw----  1 root disk 7,  2 Nov  6  2012 loop2
brw-rw----  1 root disk 7,  3 Nov  6  2012 loop3
brw-rw----  1 root disk 7,  4 Nov  6  2012 loop4
brw-rw----  1 root disk 7,  5 Nov  6  2012 loop5
brw-rw----  1 root disk 7,  6 Nov  6  2012 loop6
brw-rw----  1 root disk 7,  7 Nov  6  2012 loop7
crw-r-----  1 root kmem 1,  1 Nov  6  2012 mem
crw-rw-rw-  1 root root 1,  3 Nov  6  2012 null
crw-r-----  1 root kmem 1,  4 Nov  6  2012 port
crw-rw-rw-  1 root tty  5,  2 Nov  6  2012 ptmx
drwxr-xr-x  2 root root  4096 Nov 17  2012 pts
lrwxrwxrwx  1 root root     4 Aug 12  2016 ram -> ram1
brw-rw----  1 root disk 1,  0 Nov  6  2012 ram0
brw-rw----  1 root disk 1,  1 Nov  6  2012 ram1
brw-rw----  1 root disk 1, 10 Nov  6  2012 ram10
brw-rw----  1 root disk 1, 11 Nov  6  2012 ram11
brw-rw----  1 root disk 1, 12 Nov  6  2012 ram12
brw-rw----  1 root disk 1, 13 Nov  6  2012 ram13
brw-rw----  1 root disk 1, 14 Nov  6  2012 ram14
brw-rw----  1 root disk 1, 15 Nov  6  2012 ram15
brw-rw----  1 root disk 1, 16 Nov  6  2012 ram16
brw-rw----  1 root disk 1,  2 Nov  6  2012 ram2
brw-rw----  1 root disk 1,  3 Nov  6  2012 ram3
brw-rw----  1 root disk 1,  4 Nov  6  2012 ram4
brw-rw----  1 root disk 1,  5 Nov  6  2012 ram5
brw-rw----  1 root disk 1,  6 Nov  6  2012 ram6
brw-rw----  1 root disk 1,  7 Nov  6  2012 ram7
brw-rw----  1 root disk 1,  8 Nov  6  2012 ram8
brw-rw----  1 root disk 1,  9 Nov  6  2012 ram9
crw-rw-rw-  1 root root 1,  8 Nov  6  2012 random
drwxr-xr-x  2 root root  4096 Oct 14  2013 shm
lrwxrwxrwx  1 root root     4 Aug 12  2016 stderr -> fd/2
lrwxrwxrwx  1 root root     4 Aug 12  2016 stdin -> fd/0
lrwxrwxrwx  1 root root     4 Aug 12  2016 stdout -> fd/1
crw-rw-rw-  1 root tty  5,  0 Nov  6  2012 tty
crw-------  1 root tty  4,  0 Nov  6  2012 tty0
crw-rw-rw-  1 root root 1,  9 Nov  6  2012 urandom
crw-rw-rw-  1 root root 1,  5 Nov  6  2012 zero
root@debian:~# ls -l /tmp/md0_data/mnt
total 8
drwxr-xr-x  2 root root 4096 Jun 17  2012 .
drwxr-xr-x 25 root root 4096 Jun 10  2018 ..
root@debian:~# ls -l /tmp/md0_data/apps
total 8
drwxr-xr-x  2 root root 4096 Aug 12  2016 .
drwxr-xr-x 25 root root 4096 Jun 10  2018 ..
root@debian:~# ls -l /tmp/md0_data/home
total 8
drwxr-xr-x  2 root root 4096 Jun 17  2012 .
drwxr-xr-x 25 root root 4096 Jun 10  2018 ..
root@debian:~# ls -lR  /tmp/md127_data/Videos
/tmp/md127_data/Videos:
total 32
drwxrwxrwx+ 1   99   99  20 Aug 12  2016 .
drwxr-xr-x  1 root root 140 Aug 12  2016 ..
drwxr-xr-x  1 root   98   0 Aug 12  2016 .snapshots

/tmp/md127_data/Videos/.snapshots:
total 0
drwxr-xr-x  1 root 98  0 Aug 12  2016 .
drwxrwxrwx+ 1   99 99 20 Aug 12  2016 ..
root@debian:~# ls -lR  /tmp/md127_data/.vault
/tmp/md127_data/.vault:
total 32
drwxr-xr-x 1 root root   0 Aug 12  2016 .
drwxr-xr-x 1 root root 140 Aug 12  2016 ..
root@debian:~#

Thanks again.

Regards.

AkkJaa...
Re: RN10400
May 21, 2021 10:50PM
AkkJaa,

mount /dev/md0  /tmp/md0_data
mount /dev/md1  /tmp/md1_data
mount /dev/md127 /tmp/md127_data

To see what the mount command lists after you've mounted all 3, do a mount without arguments. And what module was loaded:
mount
lsmod

======

Your md0 is the stock rootfs. md1 is the stock swap partition. md172 is the stock data partition formatted in btrfs.

Unofrtunately, I don't use btrfs, so cannot advise you what to do.

Anybody can chime in and help AkkJaa?

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: RN10400
May 22, 2021 07:18PM
Hi Bodhi,

Here i find a link to a man who encrypt and crypt btrfs file systems and some other links to the btrfs filsystems.:-
Quote

https://linuxhint.com/encrypt-a-btrfs-filesystem/
One more link.:-
https://btrfs.wiki.kernel.org/index.php/FAQ#:~:text=All%20data%20(except%20the%20boot,%2Dcrypt)%20since%20Linux%203.2.&text=ecryptfs)%20with%20btrfs.,data%20is%20sent%20to%20btrfs.
Also here is a link.:-
https://wiki.gentoo.org/wiki/Full_Encrypted_Btrfs/Native_System_Root_Guide
And the last i found here..:-
https://wiki.archlinux.org/title/Btrfs

The first link is for Fedora and Ubuntu but maybe i can use some simular to this.

Thanks again.

Regards.

AkkJaa...



Edited 4 time(s). Last edit at 05/22/2021 07:58PM by AkkJaa.
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: