Need default /lib contents for Netgear Stora MS2110 January 24, 2021 04:32AM |
Registered: 4 years ago Posts: 15 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: RD-88F6281A LE U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell version: 3.4.14 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: 88F6281 A0 (DDR2) CPU running @ 1000Mhz L2 running @ 333Mhz SysClock = 333Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 64MB DRAM CS[1] base 0x04000000 size 64MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CRC in Flash: beb3c296, Calculated CRC: beb3c296 CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is TDM USB 0: host mode PEX 0: interface detected no Link. Net: egiga0, egiga1 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x300000 Reading data from 0x3ff800 -- 100% complete. 3145728 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18-Netgear Created: 2010-06-13 23:54:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2788728 Bytes = 2.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................................................ done, booting the kernel. Linux version 2.6.22.18-Netgear (mostafah@es5x86.axentra.com) (gcc version 4.2.1) #16 Sun Jun 13 19:54:46 EDT 2010 CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977 Machine: Feroceon-KW Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists. Total pages: 32512 Kernel command line: console=ttyS0,115200 ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 64MB 64MB 0MB 0MB = 128MB total Memory: 124800KB available (4048K code, 268K data, 692K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 64MB SDRAM_CS1 ....base 04000000, size 64MB SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e8000000, size 128MB PEX0_IO ....base f2000000, size 1MB INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21)-- RD-88F6281A Soc: 88F6281 A0 LE Detected Tclk 200000000 and SysClk 333333333 MV Buttons Device Load Marvell USB EHCI Host controller #0: c063d600 PEX0 interface detected no Link. PCI: bus0: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: kw_clocksource clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered RTC has been updated!!! RTC registered Use the XOR engines (acceleration) for enhancing the following functions: o RAID 5 Xor calculation o kernel memcpy o kenrel memzero Number of XOR engines to use: 4 cesadev_init(c000eed0) mvCesaInit: sessions=640, queue=64, pSram=f0000000 MV Buttons Driver Load JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A loop: module loaded Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o Multi RX Queue support - 4 RX queues o Multi TX Queue support - 2 TX Queues o TCP segmentation offload enabled o Receive checksum offload enabled o Transmit checksum offload enabled o Network Fast Processing (Routing) supported o Network Fast Processing (NAT) supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Proc tool API enabled o Gateway support enabled o Using Marvell Header Mode o L2 IGMP support o Rx descripors: q0=128 q1=128 q2=128 q3=128 o Tx descripors: q0=532 q1=532 o Loading network interface(s): o eth0, ifindex = 1, GbE port = 0 o eth1, ifindex = 2, GbE port = 1 mvFpRuleDb (c7977000): 1024 entries, 4096 bytes Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation Integrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter scsi 0:0:0:0: Direct-Access WDC WD10EAVS-00D7B1 01.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sda: sda1 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 368 at 0x02e00000 Bad eraseblock 369 at 0x02e20000 Bad eraseblock 618 at 0x04d40000 Bad eraseblock 700 at 0x05780000 Bad eraseblock 1012 at 0x07e80000 Bad eraseblock 1294 at 0x0a1c0000 Bad eraseblock 1393 at 0x0ae20000 Bad eraseblock 1444 at 0x0b480000 Bad eraseblock 1642 at 0x0cd40000 Bad eraseblock 2036 at 0x0fe80000 Using static partition definition Creating 3 MTD partitions on "nand_mtd": 0x00000000-0x00100000 : "u-boot" 0x00100000-0x00700000 : "uImage" 0x00700000-0x10000000 : "root" UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI warning: ubi_eba_init_scan: cannot reserve enough PEBs for bad PEB handling, reserved 19, need 38 UBI: attached mtd2 to ubi0 UBI: MTD device name: "root" UBI: MTD device size: 249 MiB UBI: number of good PEBs: 1982 UBI: number of bad PEBs: 10 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 1982 UBI: number of PEBs reserved for bad PEB handling: 19 UBI: max/mean erase counter: 89/8 UBI: background thread "ubi_bgt0d" started, PID 291 ehci_marvell ehci_marvell.70059: Marvell Orion EHCI ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected USB Universal Host Controller Interface driver v3.0 usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 raid6: int32x1 81 MB/s raid6: int32x2 95 MB/s raid6: int32x4 102 MB/s raid6: int32x8 92 MB/s raid6: using algorithm int32x4 (102 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: measuring checksumming speed arm4regs : 903.600 MB/sec 8regs : 629.200 MB/sec 32regs : 750.000 MB/sec raid5: using function: arm4regs (903.600 MB/sec) device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com dm_crypt using the OCF package. sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1024 buckets, 8192 max) mvFpNatDb (c7f77000): 1024 entries, 4096 bytes ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NFP (fdb) init 256 entries, 1024 bytes Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> md: Autodetecting RAID arrays. md: autorun ... md: considering sda1 ... md: adding sda1 ... md: created md0 md: bind<sda1> md: running: <sda1> raid1: raid set md0 active with 1 out of 2 mirrors md: ... autorun DONE. Freeing init memory: 692K Reset button not pressed Proceeding normally. UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: file system size: 239857664 bytes (234236 KiB, 228 MiB, 1889 LEBs) UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) UBIFS: media format: 4 (latest is 4) UBIFS: default compressor: zlib UBIFS: reserved for root: 0 bytes (0 KiB) >> This is the point at which it freezes <<
Re: Need default /lib contents for Netgear Stora MS2110 February 16, 2021 04:20PM |
Registered: 3 years ago Posts: 7 |