Setting GPIOs in serial console (Kirkwood SoCs) March 18, 2021 09:41PM |
Admin Registered: 13 years ago Posts: 19,007 |
md.l 0xF1010100 1 md.l 0xF1010140 1
md.l 0xF1010100 1
mw.l 0xF1010100 yyy
GPIO0: xxx = 0000 0000 0100 0010 0000 0000 0000 0000 yyy = 0010 0000 0100 0010 0000 0000 0000 0000 ^
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 19, 2021 09:29AM |
Registered: 3 years ago Posts: 24 |
Hit any key to stop autoboot: 0 NSA320>> md.l 0xF1010100 1 f1010100: 10029000 .... NSA320>> mw.l 0xF1010100 10229000 NSA320>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found NSA320>> md.l 0xF1010100 1 f1010100: 10229000 NSA320>> ext2ls usb 0:1 / ** Bad partition - usb 0:1 ** NSA320>> usb reset (Re)start USB... USB: scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found NSA320>> md.l 0xF1010100 1 f1010100: 10229000 ..". NSA320>> ext2ls usb 0:1 / ** Bad partition - usb 0:1 **
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 19, 2021 03:50PM |
Admin Registered: 13 years ago Posts: 19,007 |
scanning bus for storage devices... 0 Storage Device(s) found
Quote
Sensors & Fan & WOL
OWFSPlug : 1-Wire File System + Motion Detection Software in a NAND Package
OWFS & Motion Detection (external link)
How to control GPIO in Linux userspace for GPIO-enable fan
Zyxel NSA 310S/320S/325/326 CPU Temperature and Fan Speed reading
Zyxel NAS326 WOL
Zyxel NAS326 Auto-Power Up
Zyxel NAS326 WOL and Auto-Power Up I2C commands
Zyxel NSA320 Auto-Power Up
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 20, 2021 05:34PM |
Registered: 3 years ago Posts: 24 |
root@NSA320:~# /bin/echo 21 > /sys/class/gpio/export /bin/echo: write error: Device or resource busy
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 20, 2021 06:35PM |
Admin Registered: 13 years ago Posts: 19,007 |
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 21, 2021 08:50AM |
Registered: 3 years ago Posts: 24 |
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 21, 2021 04:19PM |
Admin Registered: 13 years ago Posts: 19,007 |
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 22, 2021 05:33PM |
Registered: 3 years ago Posts: 24 |
[root@localhost-live kwboot-tool]# ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa320.mtd0.kwb -p Sending boot message. Please reboot the target...\ Sending boot image... 0 % [......................................................................] 1 % [......................................................................] 3 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 8 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 13 % [......................................................................] 15 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 20 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 25 % [......................................................................] 27 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 32 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 37 % [......................................................................] 39 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 44 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 49 % [......................................................................] 51 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 56 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 61 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 66 % [......................................................................] 68 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 73 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 78 % [......................................................................] 80 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 85 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 90 % [......................................................................] 92 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:46:11 -0700) ZyXEL NSA320 2-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA320> printenv arcNumber=3956 baudrate=115200 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=console=ttyS0,115200 device=0:1 devices=usb ide disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3016/131068 bytes NSA320> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: .........OK Device 0: Model: SAMSUNG HD103UJ Firm: 1AA01113 Ser#: S13PJ1BQ731099 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Device 1: Model: ST4000DM005-2DP166 Firm: 0001 Ser#: ZDH0CSKF Type: Hard Disk Supports 48-bit addressing Capacity: 3815447.8 MB = 3726.0 GB (7814037168 x 512) Partition Map for USB device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x00ef7fdd "" attrs: 0x0000000000000000 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 4b7abcb5-ab7a-e54d-bcb9-3dca1ef2c384 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Partition Map for IDE device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 1953523120 0fb90fb8-01 83 Partition Map for IDE device 1 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x000f3fff "mitraswap" attrs: 0x0000000000000000 type: 0657fd6d-a4ab-43c4-84e5-0933c84b4f4f type: swap guid: 0ced66c6-0d6d-4333-bff6-d64b37dce7f8 2 0x000f4000 0x1d1c0b7ff "eexxtt44" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: 8406160e-0e36-4e5c-8d1f-840a7e4cf754 running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 692 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4976833 bytes read in 1077 ms (4.4 MiB/s) loading uInitrd ... 9713936 bytes read in 1087 ms (8.5 MiB/s) loading DTB /boot/dts/kirkwood-nsa320.dtb ... 13153 bytes read in 2722 ms (3.9 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2021-03-11 14:28:13 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4976769 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:50 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f6bc000, end 0ffff8d0 ... OK Loading Device Tree to 0f6b5000, end 0f6bb360 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000][ T0] Memory: 504168K/524288K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 20120K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000047][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000796][ T0] Console: colour dummy device 80x30 [ 0.000847][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000873][ T0] pid_max: default: 32768 minimum: 301 [ 0.001252][ T0] LSM: Security Framework initializing [ 0.001436][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001464][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002396][ T0] *** VALIDATE proc *** [ 0.002668][ T0] *** VALIDATE cgroup1 *** [ 0.002694][ T0] *** VALIDATE cgroup2 *** [ 0.002795][ T0] CPU: Testing write buffer coherency: ok [ 0.004464][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.004785][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.005066][ T1] rcu: Hierarchical SRCU implementation. [ 0.008262][ T1] devtmpfs: initialized [ 0.014241][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.014274][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.014516][ T1] xor: measuring software checksum speed [ 0.110113][ T1] arm4regs : 1047.600 MB/sec [ 0.210077][ T1] 8regs : 654.000 MB/sec [ 0.310074][ T1] 32regs : 950.800 MB/sec [ 0.310094][ T1] xor: using function: arm4regs (1047.600 MB/sec) [ 0.310115][ T1] prandom: seed boundary self test passed [ 0.314292][ T1] prandom: 100 self tests passed [ 0.314304][ T1] pinctrl core: initialized pinctrl subsystem [ 0.315724][ T1] NET: Registered protocol family 16 [ 0.316171][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.316971][ T1] audit: initializing netlink subsys (disabled) [ 0.318217][ T14] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.318337][ T1] cpuidle: using governor ladder [ 0.318413][ T1] cpuidle: using governor menu [ 0.318862][ T1] Feroceon L2: Enabling L2 [ 0.318912][ T1] Feroceon L2: Cache support initialised. [ 0.325204][ T1] No ATAGs? [ 2.560054][ C0] random: fast init done [ 6.251939][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 6.252301][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 6.430652][ T1] raid6: int32x8 gen() 128 MB/s [ 6.600319][ T1] raid6: int32x8 xor() 86 MB/s [ 6.770264][ T1] raid6: int32x4 gen() 129 MB/s [ 6.940242][ T1] raid6: int32x4 xor() 84 MB/s [ 7.110155][ T1] raid6: int32x2 gen() 133 MB/s [ 7.280192][ T1] raid6: int32x2 xor() 94 MB/s [ 7.450399][ T1] raid6: int32x1 gen() 100 MB/s [ 7.620407][ T1] raid6: int32x1 xor() 69 MB/s [ 7.620418][ T1] raid6: using algorithm int32x2 gen() 133 MB/s [ 7.620427][ T1] raid6: .... xor() 94 MB/s, rmw enabled [ 7.620435][ T1] raid6: using intx1 recovery algorithm [ 7.620689][ T1] vgaarb: loaded [ 7.621197][ T1] SCSI subsystem initialized [ 7.621692][ T1] usbcore: registered new interface driver usbfs [ 7.621756][ T1] usbcore: registered new interface driver hub [ 7.621850][ T1] usbcore: registered new device driver usb [ 7.622028][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.622040][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.622067][ T1] PTP clock support registered [ 7.623279][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.654441][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.654537][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.664374][ T1] NET: Registered protocol family 2 [ 8.665191][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 8.665228][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 8.665286][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 8.665339][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 8.665436][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 8.665464][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 8.665694][ T1] NET: Registered protocol family 1 [ 8.666332][ T1] RPC: Registered named UNIX socket transport module. [ 8.666347][ T1] RPC: Registered udp transport module. [ 8.666355][ T1] RPC: Registered tcp transport module. [ 8.666364][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.666378][ T1] PCI: CLS 0 bytes, default 32 [ 8.666699][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 8.667824][ T1] Initialise system trusted keyrings [ 8.667878][ T1] Key type blacklist registered [ 8.668107][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 8.668195][ T1] zbud: loaded [ 8.669279][ T1] NFS: Registering the id_resolver key type [ 8.669327][ T1] Key type id_resolver registered [ 8.669337][ T1] Key type id_legacy registered [ 8.669357][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 8.669374][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 8.669671][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 8.669907][ T1] fuse: init (API version 7.31) [ 8.670287][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 8.670484][ T1] orangefs_init: module version upstream loaded [ 8.670497][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 8.673700][ T1] async_tx: api initialized (async) [ 8.673721][ T1] Key type asymmetric registered [ 8.673731][ T1] Asymmetric key parser 'x509' registered [ 8.673789][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 8.675189][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 8.677152][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 8.677175][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 8.677191][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 8.677206][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 8.677332][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 8.677373][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 8.678904][ T1] PCI: bus0: Fast back to back transfers disabled [ 8.678932][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 8.680382][ T1] PCI: bus1: Fast back to back transfers enabled [ 8.680409][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 8.680612][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 8.680630][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 8.681265][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 8.744072][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.746053][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 8.804118][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.806347][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 8.807628][ T1] printk: console [ttyS0] disabled [ 8.807696][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.628875][ T1] printk: console [ttyS0] enabled [ 9.641356][ T1] loop: module loaded [ 9.645830][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 9.654259][ T1] scsi host0: sata_mv [ 9.658713][ T1] scsi host1: sata_mv [ 9.662872][ T1] ata1: SATA max UDMA/133 irq 33 [ 9.667749][ T1] ata2: SATA max UDMA/133 irq 33 [ 9.673600][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 9.680779][ T1] nand: Samsung NAND 128MiB 3,3V 8-bit [ 9.686149][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.694485][ T1] Scanning device for bad blocks [ 9.723654][ T1] Bad eraseblock 253 at 0x000001fa0000 [ 9.738254][ T1] Bad eraseblock 350 at 0x000002bc0000 [ 9.778395][ T1] Bad eraseblock 713 at 0x000005920000 [ 9.788594][ T1] Bad eraseblock 764 at 0x000005f80000 [ 9.801290][ T1] Bad eraseblock 841 at 0x000006920000 [ 9.824185][ T1] 9 fixed-partitions partitions found on MTD device orion_nand [ 9.831613][ T1] Creating 9 MTD partitions on "orion_nand": [ 9.837502][ T1] 0x000000000000-0x000000100000 : "uboot" [ 9.844444][ T1] 0x000000100000-0x000000180000 : "uboot_env" [ 9.851625][ T1] 0x000000180000-0x000000200000 : "key_store" [ 9.858848][ T1] 0x000000200000-0x000000280000 : "info" [ 9.865641][ T1] 0x000000280000-0x000000c80000 : "etc" [ 9.872339][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 9.879520][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 9.886731][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 9.893927][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 9.902362][ T1] libphy: Fixed MDIO Bus: probed [ 9.908042][ T1] libphy: orion_mdio_bus: probed [ 9.914162][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 9.922204][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 9.929652][ T1] mv643xx_eth: Set the PHY to fix link down [ 9.930452][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 9.945925][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.953243][ T1] ehci-pci: EHCI PCI platform driver [ 9.958550][ T1] ehci-orion: EHCI orion driver [ 9.963518][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 9.969814][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 9.978433][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 10.013306][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.020335][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 10.029371][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.037354][ T1] usb usb1: Product: EHCI Host Controller [ 10.042953][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 10.050315][ T1] usb usb1: SerialNumber: f1050000.ehci [ 10.056361][ T1] hub 1-0:1.0: USB hub found [ 10.060867][ T1] hub 1-0:1.0: 1 port detected [ 10.066266][ T1] usbcore: registered new interface driver usb-storage [ 10.073414][ T1] mousedev: PS/2 mouse device common for all mice [ 10.080269][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 10.086189][ T1] i2c /dev entries driver [ 10.096984][ T1] rtc-pcf8563 0-0051: registered as rtc1 [ 10.104171][ T1] device-mapper: uevent: version 1.0.3 [ 10.109800][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 10.119430][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 10.126761][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 10.134155][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 10.141560][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 10.148413][ T1] device-mapper: raid: Loading target version 1.14.0 [ 10.157007][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 10.163488][ T1] drop_monitor: Initializing network drop monitor service [ 10.170797][ T1] NET: Registered protocol family 17 [ 10.176079][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 10.183679][ T1] Key type dns_resolver registered [ 10.189536][ T1] registered taskstats version 1 [ 10.194389][ T1] Loading compiled-in X.509 certificates [ 10.199985][ T1] zswap: loaded using pool lzo/zbud [ 10.213612][ T112] ata1.00: ATA-7: SAMSUNG HD103UJ, 1AA01113, max UDMA7 [ 10.220355][ T112] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 10.234891][ T1] Key type big_key registered [ 10.243226][ T1] Key type encrypted registered [ 10.250015][ T1] rtc-mv f1010300.rtc: setting system clock to 2021-03-22T22:01:08 UTC (1616450468) [ 10.263701][ T112] ata1.00: configured for UDMA/133 [ 10.279218][ T7] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1113 PQ: 0 ANSI: 5 [ 10.289075][ T116] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 10.298193][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 10.303924][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 10.317954][ T116] sda: sda1 [ 10.322444][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 10.443310][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 10.645065][ T15] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63 [ 10.654013][ T15] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 10.661899][ T15] usb 1-1: Product: USB2.0 Hub [ 10.667348][ T15] hub 1-1:1.0: USB hub found [ 10.672187][ T15] hub 1-1:1.0: 4 ports detected [ 10.803321][ T114] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 10.835640][ T114] ata2.00: ATA-10: ST4000DM005-2DP166, 0001, max UDMA/133 [ 10.842640][ T114] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 10.857061][ T114] ata2.00: configured for UDMA/133 [ 10.872531][ T23] scsi 1:0:0:0: Direct-Access ATA ST4000DM005-2DP1 0001 PQ: 0 ANSI: 5 [ 10.882374][ T116] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB) [ 10.891237][ T116] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 10.897373][ T116] sd 1:0:0:0: [sdb] Write Protect is off [ 10.903086][ T116] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 10.962058][ T116] sdb: sdb1 sdb2 [ 10.967316][ T116] sd 1:0:0:0: [sdb] Attached SCSI disk [ 10.972756][ T1] md: Waiting for all devices to be available before autodetect [ 10.980347][ T1] md: If you don't use raid, use raid=noautodetect [ 10.987450][ T1] md: Autodetecting RAID arrays. [ 10.992270][ T1] md: autorun ... [ 10.995855][ T1] md: ... autorun DONE. [ 11.000098][ T1] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 11.008370][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 11.017534][ T15] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 11.025196][ T1] 1f00 1024 mtdblock0 [ 11.025200][ T1] (driver?) [ 11.033164][ T1] 1f01 512 mtdblock1 [ 11.033166][ T1] (driver?) [ 11.041224][ T1] 1f02 512 mtdblock2 [ 11.041227][ T1] (driver?) [ 11.049312][ T1] 1f03 512 mtdblock3 [ 11.049316][ T1] (driver?) [ 11.057376][ T1] 1f04 10240 mtdblock4 [ 11.057380][ T1] (driver?) [ 11.065396][ T1] 1f05 10240 mtdblock5 [ 11.065399][ T1] (driver?) [ 11.073385][ T1] 1f06 48896 mtdblock6 [ 11.073388][ T1] (driver?) [ 11.081360][ T1] 1f07 10240 mtdblock7 [ 11.081363][ T1] (driver?) [ 11.089386][ T1] 1f08 48896 mtdblock8 [ 11.089389][ T1] (driver?) [ 11.097431][ T1] 0800 976762584 sda [ 11.097435][ T1] driver: sd [ 11.105035][ T1] 0801 976761560 sda1 0fb90fb8-01 [ 11.105039][ T1] [ 11.112860][ T1] 0810 3907018584 sdb [ 11.112863][ T1] driver: sd [ 11.120417][ T1] 0811 498688 sdb1 0ced66c6-0d6d-4333-bff6-d64b37dce7f8 [ 11.120420][ T1] [ 11.130418][ T1] 0812 3906518016 sdb2 8406160e-0e36-4e5c-8d1f-840a7e4cf754 [ 11.130421][ T1] [ 11.140413][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 11.149419][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.9-kirkwood-tld-1 #1 [ 11.157104][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 11.164125][ T1] [<c010f6ac>] (unwind_backtrace) from [<c010bb00>] (show_stack+0x10/0x14) [ 11.172616][ T1] [<c010bb00>] (show_stack) from [<c0119fa0>] (panic+0xe0/0x30c) [ 11.180237][ T1] [<c0119fa0>] (panic) from [<c0e01628>] (mount_block_root+0x1bc/0x2a4) [ 11.188463][ T1] [<c0e01628>] (mount_block_root) from [<c0e017f8>] (mount_root+0xe8/0x154) [ 11.197034][ T1] [<c0e017f8>] (mount_root) from [<c0e019b0>] (prepare_namespace+0x14c/0x18c) [ 11.205780][ T1] [<c0e019b0>] (prepare_namespace) from [<c0e011c8>] (kernel_init_freeable+0x270/0x2dc) [ 11.215400][ T1] [<c0e011c8>] (kernel_init_freeable) from [<c09dcee0>] (kernel_init+0x8/0x10c) [ 11.224318][ T1] [<c09dcee0>] (kernel_init) from [<c01010e0>] (ret_from_fork+0x14/0x34) [ 11.232621][ T1] Exception stack(0xdf48bfb0 to 0xdf48bff8) [ 11.238395][ T1] bfa0: 00000000 00000000 00000000 00000000 [ 11.247309][ T1] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 11.256220][ T1] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 11.263570][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 23, 2021 12:40AM |
Admin Registered: 13 years ago Posts: 19,007 |
Quote
https://forum.doozan.com/read.php?2,12096
4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Do not do this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).
cp -a uImage.orig uImage
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 23, 2021 04:58PM |
Registered: 3 years ago Posts: 24 |
# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 # cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 00080000 00020000 "uboot_env" mtd2: 00080000 00020000 "key_store" mtd3: 00080000 00020000 "info" mtd4: 00a00000 00020000 "etc" mtd5: 00a00000 00020000 "kernel_1" mtd6: 02fc0000 00020000 "rootfs1" mtd7: 00a00000 00020000 "kernel_2" mtd8: 02fc0000 00020000 "rootfs2" # dmesg |grep -i bad [ 10.405197] Scanning device for bad blocks [ 10.434297] Bad eraseblock 253 at 0x000001fa0000 [ 10.448872] Bad eraseblock 350 at 0x000002bc0000 [ 10.488882] Bad eraseblock 713 at 0x000005920000 [ 10.499066] Bad eraseblock 764 at 0x000005f80000 [ 10.511736] Bad eraseblock 841 at 0x000006920000 # fw_printenv ethaddr Warning: Bad CRC, using default environment ethaddr=00:00:11:22:33:44 # fw_printenv Warning: Bad CRC, using default environment bootcmd=run distro_bootcmd bootdelay=2 baudrate=115200 stdin=serial,cros-ec-keyb,usbkbd stdout=serial,vidconsole stderr=serial,vidconsole ethaddr=00:00:11:22:33:44 eth1addr=00:00:11:22:33:45 eth3addr=00:00:11:22:33:46 eth5addr=00:00:11:22:33:47 ipaddr=1.2.3.4 host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi sata_boot=if sata dev ${devnum}; then setenv devtype sata; run scan_dev_for_boot_part; fi scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi virtio_boot=if virtio dev ${devnum}; then setenv devtype virtio; run scan_dev_for_boot_part; fi boot_prefixes=/ /boot/ boot_scripts=boot.scr.uimg boot.scr boot_script_dhcp=boot.scr.uimg boot_targets=host1 host0 boot_syslinux_conf=extlinux/extlinux.conf boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf} scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done bootcmd_host1=setenv devnum 1; run host_boot bootcmd_host0=setenv devnum 0; run host_boot distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done bootm_size=0x10000000 kernel_addr_r=0x1000000 fdt_addr_r=0xc00000 ramdisk_addr_r=0x2000000 scriptaddr=0x1000 pxefile_addr_r=0x2000
NSA320>> saveenv Saving Environment to NAND... Erasing Nand...Writing to Nand... done NSA320>> printenv bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootdelay=2 baudrate=115200 loads_echo=0 eth1addr=00:19:CB:00:51:82 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 nandEcc=1bit MODEL_ID=DD01 PRODUCT_NAME=NSA-320 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=ZyXEL Communications Corp. run_diag=yes ethaddr=B0:B2:DC:F0:FF:12 stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) mainlineLinux=no CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes ethprime=egiga1 netbsd_en=no vxworks_en=no bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; disaMvPnp=no ethmtu=1500 eth1mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 hddPowerCtrl=no netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no enaAutoRecovery=yes kernel_addr=0x4640000 pcieTune=no ethact=egiga1 ide_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial init=/bin/systemd load_uimage=ext2load ide 0:1 0x800000 /boot/uImage load_uinitrd=ext2load ide 0:1 0x2100000 /boot/uInitrd ide_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000 ide_bootcmd=run ide_set_bootargs; run ide_boot bootcmd=ide reset; ide start; run ide_bootcmd; ide stop; reset Environment size: 1910/131068 bytes
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 23, 2021 07:05PM |
Admin Registered: 13 years ago Posts: 19,007 |
Quote
8. Flashing default u-boot envs image (if you are upgrading from 2016.05-tld-1 u-boot, you can skip this step 8).
cd /boot cp -a uImage uImage.with_DTB cp -a uImage.orig uImage sync
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 24, 2021 04:08PM |
Registered: 3 years ago Posts: 24 |
# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 # cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 00080000 00020000 "uboot_env" mtd2: 00080000 00020000 "key_store" mtd3: 00080000 00020000 "info" mtd4: 00a00000 00020000 "etc" mtd5: 00a00000 00020000 "kernel_1" mtd6: 02fc0000 00020000 "rootfs1" mtd7: 00a00000 00020000 "kernel_2" mtd8: 02fc0000 00020000 "rootfs2"
# fw_printenv > current_envs.txt
# cat current_envs.txt bootcmd=run distro_bootcmd bootdelay=2 baudrate=115200 stdin=serial,cros-ec-keyb,usbkbd stdout=serial,vidconsole stderr=serial,vidconsole ethaddr=00:00:11:22:33:44 eth1addr=00:00:11:22:33:45 eth3addr=00:00:11:22:33:46 eth5addr=00:00:11:22:33:47 ipaddr=1.2.3.4 host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi sata_boot=if sata dev ${devnum}; then setenv devtype sata; run scan_dev_for_boot_part; fi scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi virtio_boot=if virtio dev ${devnum}; then setenv devtype virtio; run scan_dev_for_boot_part; fi boot_prefixes=/ /boot/ boot_scripts=boot.scr.uimg boot.scr boot_script_dhcp=boot.scr.uimg boot_targets=host1 host0 boot_syslinux_conf=extlinux/extlinux.conf boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf} scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done bootcmd_host1=setenv devnum 1; run host_boot bootcmd_host0=setenv devnum 0; run host_boot distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done bootm_size=0x10000000 kernel_addr_r=0x1000000 fdt_addr_r=0xc00000 ramdisk_addr_r=0x2000000 scriptaddr=0x1000 pxefile_addr_r=0x2000
# flash_erase /dev/mtd0 0 4 Erasing 128 Kibyte @ 60000 -- 100 % complete
# nandwrite /dev/mtd0 uboot.2017.07-tld-1.nsa320.mtd0.kwb Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x 60000
# /usr/sbin/flash_erase /dev/mtd0 0xc0000 1 Erasing 128 Kibyte @ c0000 -- 100 % complete # /usr/sbin/nandwrite -s 786432 /dev/mtd0 uboot.2016.05-tld-1.environment.img Writing data to block 6 at offset 0xc0000 # fw_printenv arcNumber=2097 bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking dtb_file=/boot/dts/kirkwood-pogo_e02.dtb load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage machid=0x831 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15
# fw_setenv arcNumber 3956 # fw_setenv machid
# fw_setenv ethaddr '0B:B2:DC:F0:FF:21'
# fw_setenv uenv_init_devices 'echo Initializing devices...; setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done' # fw_setenv uenv_read 'echo Loading envs from $device_type $disk_number...; if load $device_type $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi' # fw_setenv uenv_load 'run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done;' # fw_setenv uenv_read_disk
# fw_setenv dtb_file '/boot/dts/kirkwood-nsa320.dtb'
# fw_printenv bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize usb_ready_retry=15 arcNumber=3956 ethaddr=0B:B2:DC:F0:FF:21 uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_type $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done; dtb_file=/boot/dts/kirkwood-nsa320.dtb
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 24, 2021 05:04PM |
Admin Registered: 13 years ago Posts: 19,007 |
fw_setenv mtdparts 'mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)'
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 24, 2021 05:24PM |
Registered: 3 years ago Posts: 24 |
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:46:11 -0700) ZyXEL NSA320 2-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA320> printenv arcNumber=3956 baudrate=115200 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=console=ttyS0,115200 device=0:1 devices=usb ide disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3016/131068 bytes
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 24, 2021 10:14PM |
Admin Registered: 13 years ago Posts: 19,007 |
mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 25, 2021 04:22PM |
Registered: 3 years ago Posts: 24 |
mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) devices=usb ide mmc customparams=init=/bin/systemd
i2cset -y 0x0 0x50 0x06 0x01 b
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 25, 2021 06:56PM |
Admin Registered: 13 years ago Posts: 19,007 |
> mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) > devices=usb ide mmc > customparams=init=/bin/systemd >
> i2cset -y 0x0 0x50 0x06 0x01 b >>
Quote
Sensors & Fan & WOL
OWFSPlug : 1-Wire File System + Motion Detection Software in a NAND Package
OWFS & Motion Detection (external link)
How to control GPIO in Linux userspace for GPIO-enable fan
Zyxel NSA 310S/320S/325/326 CPU Temperature and Fan Speed reading
Zyxel NAS326 WOL
Zyxel NAS326 Auto-Power Up
Zyxel NAS326 WOL and Auto-Power Up I2C commands
Zyxel NSA320 Auto-Power Up
Re: Setting GPIOs in serial console (Kirkwood SoCs) March 26, 2021 09:53AM |
Registered: 3 years ago Posts: 24 |
i2cset -y 0x0 0x50 0x06 0x01 b
[WOL + AUTO RESUME] If you want WOL + auto turn on after power loss: /usr/sbin/i2cset -y 0x0 0xa 0xa 0x0006 w (ENABLE WOL) /usr/sbin/i2cset -y 0x0 0x0a 0x0a 0x0107 w (ENABLE AUTO RESUME)
# /usr/sbin/i2cset -y 0x0 0xa 0xa 0x0006 w Error: Write failed /usr/sbin/i2cset -y 0x0 0x0a 0x0a 0x0107 w Error: Write failed
Re: Setting GPIOs in serial console (Kirkwood SoCs) October 10, 2023 01:53PM |
Registered: 1 year ago Posts: 80 |