Welcome! Log In Create A New Profile

Advanced

Pogoplug Wont Accept Commands after interrupt

Posted by erWill2 
Pogoplug Wont Accept Commands after interrupt
January 25, 2019 11:19PM
Hello, I decided to give hacking one of these a try. Its seems as though any command I send through putty is not getting executed. Uboot does recognize the interrupt but does nothing after. Any suggestions would be greatly appreciated. This is the bootlog without interrupting. Thanks!

U-Boot 1.1.4 (Oct  1 2011 - 12:21:35) Cloud Engines 1.1.2 (3.4.27) PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006918B4

Soc: 88F6192 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV4A1

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0

Loading from NAND 128MB 3,3V 8-bit, offset 0x200000
   Image Name:   Linux-2.6.31.8
   Created:      2011-08-23  20:00:55 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2080956 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2011-08-23  20:00:55 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2080956 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux..................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #4 Tue Aug 23 13:00:50 PDT 2011
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Feroceon-KW
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Ignoring unrecognised tag 0x41004345
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] CPU: Testing write buffer coherency: ok
[    0.230000] NET: Registered protocol family 16
[    0.230000] Feroceon L2: Enabling L2
[    0.230000] Feroceon L2: Cache support initialised.
[    0.230000]
[    0.230000] CPU Interface
[    0.230000] -------------
[    0.230000] SDRAM_CS0 ....base 00000000, size 128MB
[    0.230000] SDRAM_CS1 ....disable
[    0.230000] SDRAM_CS2 ....disable
[    0.230000] SDRAM_CS3 ....disable
[    0.230000] PEX0_MEM ....base e0000000, size 128MB
[    0.230000] PEX0_IO ....base f2000000, size   1MB
[    0.230000] PEX1_MEM ....no such
[    0.230000] PEX1_IO ....no such
[    0.230000] INTER_REGS ....base f1000000, size   1MB
[    0.230000] NFLASH_CS ....base fa000000, size   2MB
[    0.230000] SPI_CS ....base f4000000, size  16MB
[    0.230000] BOOT_ROM_CS ....no such
[    0.230000] DEV_BOOTCS ....no such
[    0.230000] CRYPT_ENG ....base f0000000, size   2MB
[    0.230000]
[    0.230000]   Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- RD-88F6192A-NAS  Soc: 88F6192 A1 LE
[    0.230000]
[    0.230000]  Detected Tclk 166666667 and SysClk 200000000
[    0.230000] Marvell USB EHCI Host controller #0: c403e740
[    0.730000] PEX0 interface detected no Link.
[    0.730000] PCI: bus0: Fast back to back transfers enabled
[    0.730000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[    0.750000] bio: create slab <bio-0> at 0
[    0.750000] SCSI subsystem initialized
[    0.750000] usbcore: registered new interface driver usbfs
[    0.750000] usbcore: registered new interface driver hub
[    0.750000] usbcore: registered new device driver usb
[    0.750000] NET: Registered protocol family 2
[    0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.750000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.750000] TCP reno registered
[    0.750000] NET: Registered protocol family 1
[    0.750000] cpufreq: Init kirkwood cpufreq driver
[    0.760000] XOR registered 4 channels
[    0.760000] XOR 2nd invalidate WA enabled
[    0.760000] cesadev_init(c000d7fc)
[    0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[    0.760000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.770000] msgmni has been set to 231
[    0.770000] alg: No test for cipher_null (cipher_null-generic)
[    0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[    0.770000] alg: No test for digest_null (digest_null-generic)
[    0.770000] alg: No test for compress_null (compress_null-generic)
[    0.780000] alg: No test for stdrng (krng)
[    0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[    0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.790000] io scheduler noop registered
[    0.790000] io scheduler anticipatory registered (default)
[    0.790000] Initializing ths8200_init
[    0.790000] Initializing dove_adi9889_init
[    0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    0.810000] console [ttyS0] enabled
[    0.820000] Integrated Sata device found
[    0.830000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
[    0.850000] scsi0 : Marvell SCSI to SATA adapter
[    0.860000] scsi1 : Marvell SCSI to SATA adapter
[    0.870000] Loading Marvell Ethernet Driver:
[    0.870000]   o Cached descriptors in DRAM
[    0.880000]   o DRAM SW cache-coherency
[    0.880000]   o 1 Giga ports supported
[    0.880000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    0.890000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    0.890000]   o TCP segmentation offload (TSO) supported
[    0.900000]   o Large Receive offload (LRO) supported
[    0.900000]   o Receive checksum offload supported
[    0.910000]   o Transmit checksum offload supported
[    0.910000]   o Network Fast Processing (Routing) supported - (Disabled)
[    0.920000]   o Driver ERROR statistics enabled
[    0.930000]   o Proc tool API enabled
[    0.930000]   o SKB Reuse supported - (Disabled)
[    0.930000]   o SKB Recycle supported - (Disabled)
[    0.940000]   o Rx descripors: q0=128
[    0.940000]   o Tx descripors: q0=532
[    0.950000]   o Loading network interface(s):
[    0.950000]      o register under mv88fx_eth platform
[    0.960000]      o eth0, ifindex = 2, GbE port = 0
[    0.960000]
[    0.960000] mvFpRuleDb (c45b2000): 1024 entries, 4096 bytes
[    0.970000] Counter=0, opIdx=6, overhead=16
[    0.970000] Counter=1, opIdx=2, overhead=0
[    0.980000] Counter=2, opIdx=1, overhead=18
[    0.980000] Counter=3, opIdx=2, overhead=0
[    0.990000] tun: Universal TUN/TAP device driver, 1.6
[    0.990000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.000000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[    1.010000] Scanning device for bad blocks
[    1.050000] Bad eraseblock 941 at 0x0000075a0000
[    1.060000] Using static partition definition
[    1.070000] Creating 5 MTD partitions on "nand_mtd":
[    1.070000] 0x000000000000-0x000000200000 : "u-boot"
[    1.080000] 0x000000200000-0x000000500000 : "uImage"
[    1.080000] 0x000000500000-0x000000800000 : "uImage2"
[    1.090000] 0x000000800000-0x000001000000 : "failsafe"
[    1.090000] 0x000001000000-0x000008000000 : "root"
[    1.100000] UBI: attaching mtd4 to ubi0
[    1.100000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[    1.110000] UBI: logical eraseblock size:    126976 bytes
[    1.120000] UBI: smallest flash I/O unit:    2048
[    1.120000] UBI: sub-page size:              512
[    1.120000] UBI: VID header offset:          2048 (aligned 2048)
[    1.130000] UBI: data offset:                4096
[    1.350000] UBI: attached mtd4 to ubi0
[    1.360000] UBI: MTD device name:            "root"
[    1.360000] UBI: MTD device size:            112 MiB
[    1.370000] UBI: number of good PEBs:        895
[    1.370000] UBI: number of bad PEBs:         1
[    1.380000] UBI: max. allowed volumes:       128
[    1.380000] UBI: wear-leveling threshold:    4096
[    1.390000] UBI: number of internal volumes: 1
[    1.390000] UBI: number of user volumes:     1
[    1.390000] UBI: available PEBs:             0
[    1.400000] UBI: total number of reserved PEBs: 895
[    1.400000] UBI: number of PEBs reserved for bad PEB handling: 8
[    1.410000] UBI: max/mean erase counter: 1/0
[    1.410000] UBI: image sequence number: 0
[    1.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.420000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[    1.430000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[    1.440000] UBI: background thread "ubi_bgt0d" started, PID 451
[    1.470000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[    1.490000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
[    1.490000] usb usb1: configuration #1 chosen from 1 choice
[    1.500000] hub 1-0:1.0: USB hub found
[    1.500000] hub 1-0:1.0: 1 port detected
[    1.510000] Initializing USB Mass Storage driver...
[    1.510000] usbcore: registered new interface driver usb-storage
[    1.520000] USB Mass Storage support registered.
[    1.520000] usbcore: registered new interface driver ums-datafab
[    1.530000] usbcore: registered new interface driver ums-freecom
[    1.530000] usbcore: registered new interface driver ums-jumpshot
[    1.540000] usbcore: registered new interface driver ums-sddr09
[    1.550000] usbcore: registered new interface driver ums-sddr55
[    1.550000] usbcore: registered new interface driver ums-usbat
[    1.560000] mice: PS/2 mouse device common for all mice
[    1.560000] i2c /dev entries driver
[    1.580000] sdhci: Secure Digital Host Controller Interface driver
[    1.580000] sdhci: Copyright(c) Pierre Ossman
[    1.590000] mmc0: mvsdio driver initialized, using GPIO 27 for card detection
[    1.600000] usbcore: registered new interface driver usbhid
[    1.600000] usbhid: v2.6:USB HID core driver
[    1.610000] TCP cubic registered
[    1.610000] NET: Registered protocol family 17
[    1.620000] RPC: Registered udp transport module.
[    1.620000] RPC: Registered tcp transport module.
[    1.630000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.770000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.770000] UBIFS: file system size:   110723072 bytes (108128 KiB, 105 MiB, 872 LEBs)
[    1.780000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[    1.790000] UBIFS: media format:       w4/r0 (latest is w4/r0)
[    1.790000] UBIFS: default compressor: lzo
[    1.800000] UBIFS: reserved for root:  0 bytes (0 KiB)
[    1.800000] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    1.810000] Freeing init memory: 124K
[    4.180000] eth0: link down
[    4.180000] eth0: started
udhcpc (v1.16.1) started
HWADDR 00 0x25 0x31 0x05 0xe8 0x12
PIP0 232
PIP1 18
cat: can't open '/etc/resolv.conf': No such file or directory
route: SIOCDELRT: No such process
grep: /etc/resolv.conf: No such file or directory
Sending discover...
[    5.190000] eth0: link up, full duplex, speed 1 Gbps
Sending discover...
Sending discover...
Sending select for 192.168.0.249...
Lease of 192.168.0.249 obtained, lease time 86400
HWADDR 00 0x25 0x31 0x05 0xe8 0x12
PIP0 232
PIP1 18
route: SIOCDELRT: No such process
modprobe: module 'vfat' not found
[   12.200000] ufsd: module license 'Commercial product' taints kernel.
[   12.210000] Disabling lock debugging due to kernel taint
[   12.240000] ufsd: driver 8.5 (NTFS4LINUX_U85_017_S[2011-08-17-16:51:48]) LBD=ON with delayalloc with ioctl loaded at bf000000
[   12.240000] NTFS support included
[   12.240000] Hfs+/HfsX support included
[   12.240000] For 'CloudEngines_PogoPlug_2011-08-03'
Loading rt3070sta.ko:        [   12.580000] rtusb init rt2870 --->
[   12.590000] usbcore: registered new interface driver rt2870
Success
Loading xce.ko:              [   12.610000] Cloud Engines XCE Init [Version: 3.1.99.12]
[   12.620000] XCE: CPU MEMORY MAP:
[   12.620000] XCE:   -- 0x00001000 - 0xbeffffff (3055 MB)  User Space Mappings
[   12.630000] XCE:   -- 0xbf000000 - 0xbfffffff (  16 MB)  Kernel module space
[   12.640000] XCE:   -- 0xc0000000 - 0xc7ffffff ( 128 MB)  Kernel direct-mapped ram
[   12.640000] XCE:   -- 0xc8800000 - 0xe7ffffff ( 504 MB)  Kernel vmalloc space
[   12.650000] XCE:   -- 0xe8000000 - 0xfeffffff ( 367 MB)  Kernel platform space
[   12.660000] XCE: CPU FEATURES:
[   12.660000] XCE:   -- I Cache:         enabled
[   12.660000] XCE:   -- D Cache:         enabled
[   12.670000] XCE:   -- Branch Predict:  disabled
[   12.670000] XCE:   -- MMU:             enabled
[   12.680000] XCE:   -- Alignment Abort: enabled
[   12.690000] XCE: BLPARAMS:   -- Loading properties [c4bffefc].
[   12.690000] XCE: BLPARAMS:   -- MTD @ [c45c0c00].
[   12.700000] XCE: BLPARAMS: Locating parameter block...
[   12.700000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[   12.710000] XCE: Loaded Property Size: 2048
[   12.710000] XCE:    - 'cesvcid' -> 'GL6SYKKSQE7BBS9MC67LB9LBMJ'
[   12.720000] XCE:    - 'ceboardver' -> 'PPV4A1'
[   12.720000] XCE:   -- ICache Prefetch: enabled
[   12.730000] XCE:   -- DCache Prefetch: enabled
[   12.730000] XCE:   -- L2 Cache:        enabled
[   12.740000] XCE:   -- L2 Prefetch:     disabled
[   12.740000] XCE:   -- L2 Writethrough: disabled
[   12.750000] XCE:   -- Write Allocate:  disabled
[   12.750000] XCE:   -- Streaming:       disabled
[   12.760000] XCE: Current GPIO State:
[   12.760000] XCE:  GPIO L OUT:    0x01e18400
[   12.760000] XCE:  GPIO L OE:     0xfe004800
[   12.770000] XCE:  GPIO L BLINK:  0x00000000
[   12.770000] XCE:  GPIO L POL:    0x08000000
[   12.780000] XCE:  GPIO L IN:     0x11e00000
[   12.780000] XCE:  GPIO H OUT:    0x00000008
[   12.780000] XCE:  GPIO H OE:     0x00000005
[   12.790000] XCE:  GPIO H BLINK:  0x00000000
[   12.790000] XCE:  GPIO H POL:    0x00000000
[   12.800000] XCE:  GPIO H IN:     0x00000008
Success
Starting hbplug:             Success
/ # [   12.890000] XCE: BLPARAMS:   -- Loading properties [c4bffecc].
[   12.890000] XCE: BLPARAMS:   -- MTD @ [c45c0c00].
[   12.900000] XCE: BLPARAMS: Locating parameter block...
[   12.900000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[   12.910000] XCE: BLPARAMS: reading 2048 bytes @ a0800
[   12.910000] XCE: BLPARAMS: reading 2048 bytes @ a1000
[   12.920000] XCE: BLPARAMS: reading 2048 bytes @ a1800
[   18.170000] XCE: XCE: LED -> DISCONNECTED

Re: Pogoplug Wont Accept Commands after interrupt
January 25, 2019 11:25PM
Here is the interrupted log.

U-Boot 1.1.4 (Oct  1 2011 - 12:21:35) Clou$ Engines 1.1.2 (3.4.27) PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006918B4

Soc: 88F6192 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:5128 MB
55Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
5CLOUD ENGINES BOARD: PPV4A1
5
Streaming disabled
Write allocate disabled


USB 0: host mode
55PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
CE>> printenv
Re: Pogoplug Wont Accept Commands after interrupt
January 26, 2019 08:02AM
erWill2 Wrote:
-------------------------------------------------------
> Here is the interrupted log.
>
>
> U-Boot 1.1.4 (Oct  1 2011 - 12:21:35) Clou$
> Engines 1.1.2 (3.4.27) PHYADDR=0
> 
> U-Boot code: 00600000 -> 0067FFF0  BSS: ->
> 006918B4
> 
> Soc: 88F6192 A1 (DDR2)
> CPU running @ 800Mhz L2 running @ 400Mhz
> SysClock = 200Mhz , TClock = 166Mhz
> 
> DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
> DRAM CS[0] base 0x00000000   size 128MB
> DRAM Total size 128MB  16bit width
> Addresses 8M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (8M - 7M): Done
> NAND:5128 MB
> 55Flash:  0 kB
> 
> CPU : Marvell Feroceon (Rev 1)
> 5CLOUD ENGINES BOARD: PPV4A1
> 5
> Streaming disabled
> Write allocate disabled
> 
> 
> USB 0: host mode
> 55PEX 0: interface detected no Link.
> Net:   egiga0 [PRIME]
> Hit any key to stop autoboot:  0
> CE>> printenv
>

Have you checked you putty terminal session parameters? What do they look like?

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug Wont Accept Commands after interrupt
January 26, 2019 12:54PM
Thanks for the reply bodhi. Here are my params

Serial Options
Speed 115200
Data bits 8
Stop bits 1
Parity None
Flow Control None

I'v also tried with Flow Control - XON/XOFF



Edited 1 time(s). Last edit at 01/26/2019 12:56PM by erWill2.
Re: Pogoplug Wont Accept Commands after interrupt
January 26, 2019 05:03PM
Figured it out...... Bad Ground Connection. Re-soldered it and its working great!!! Now time to get this thing running.
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: