|
Pogoplug Wont Accept Commands after interrupt January 26, 2019 12:19AM |
Registered: 6 years ago Posts: 4 |
U-Boot 1.1.4 (Oct 1 2011 - 12:21:35) Cloud Engines 1.1.2 (3.4.27) PHYADDR=0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006918B4 Soc: 88F6192 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Loading from NAND 128MB 3,3V 8-bit, offset 0x200000 Image Name: Linux-2.6.31.8 Created: 2011-08-23 20:00:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 ## Booting image at 00800000 ... Image Name: Linux-2.6.31.8 Created: 2011-08-23 20:00:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................................................................... done, booting the kernel. [ 0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #4 Tue Aug 23 13:00:50 PDT 2011 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Ignoring unrecognised tag 0x41004345 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) [ 0.230000] Mount-cache hash table entries: 512 [ 0.230000] CPU: Testing write buffer coherency: ok [ 0.230000] NET: Registered protocol family 16 [ 0.230000] Feroceon L2: Enabling L2 [ 0.230000] Feroceon L2: Cache support initialised. [ 0.230000] [ 0.230000] CPU Interface [ 0.230000] ------------- [ 0.230000] SDRAM_CS0 ....base 00000000, size 128MB [ 0.230000] SDRAM_CS1 ....disable [ 0.230000] SDRAM_CS2 ....disable [ 0.230000] SDRAM_CS3 ....disable [ 0.230000] PEX0_MEM ....base e0000000, size 128MB [ 0.230000] PEX0_IO ....base f2000000, size 1MB [ 0.230000] PEX1_MEM ....no such [ 0.230000] PEX1_IO ....no such [ 0.230000] INTER_REGS ....base f1000000, size 1MB [ 0.230000] NFLASH_CS ....base fa000000, size 2MB [ 0.230000] SPI_CS ....base f4000000, size 16MB [ 0.230000] BOOT_ROM_CS ....no such [ 0.230000] DEV_BOOTCS ....no such [ 0.230000] CRYPT_ENG ....base f0000000, size 2MB [ 0.230000] [ 0.230000] Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- RD-88F6192A-NAS Soc: 88F6192 A1 LE [ 0.230000] [ 0.230000] Detected Tclk 166666667 and SysClk 200000000 [ 0.230000] Marvell USB EHCI Host controller #0: c403e740 [ 0.730000] PEX0 interface detected no Link. [ 0.730000] PCI: bus0: Fast back to back transfers enabled [ 0.730000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1 [ 0.750000] bio: create slab <bio-0> at 0 [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.750000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.750000] TCP reno registered [ 0.750000] NET: Registered protocol family 1 [ 0.750000] cpufreq: Init kirkwood cpufreq driver [ 0.760000] XOR registered 4 channels [ 0.760000] XOR 2nd invalidate WA enabled [ 0.760000] cesadev_init(c000d7fc) [ 0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.760000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.770000] msgmni has been set to 231 [ 0.770000] alg: No test for cipher_null (cipher_null-generic) [ 0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null) [ 0.770000] alg: No test for digest_null (digest_null-generic) [ 0.770000] alg: No test for compress_null (compress_null-generic) [ 0.780000] alg: No test for stdrng (krng) [ 0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic)) [ 0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.790000] io scheduler noop registered [ 0.790000] io scheduler anticipatory registered (default) [ 0.790000] Initializing ths8200_init [ 0.790000] Initializing dove_adi9889_init [ 0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.810000] console [ttyS0] enabled [ 0.820000] Integrated Sata device found [ 0.830000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs [ 0.850000] scsi0 : Marvell SCSI to SATA adapter [ 0.860000] scsi1 : Marvell SCSI to SATA adapter [ 0.870000] Loading Marvell Ethernet Driver: [ 0.870000] o Cached descriptors in DRAM [ 0.880000] o DRAM SW cache-coherency [ 0.880000] o 1 Giga ports supported [ 0.880000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.890000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.890000] o TCP segmentation offload (TSO) supported [ 0.900000] o Large Receive offload (LRO) supported [ 0.900000] o Receive checksum offload supported [ 0.910000] o Transmit checksum offload supported [ 0.910000] o Network Fast Processing (Routing) supported - (Disabled) [ 0.920000] o Driver ERROR statistics enabled [ 0.930000] o Proc tool API enabled [ 0.930000] o SKB Reuse supported - (Disabled) [ 0.930000] o SKB Recycle supported - (Disabled) [ 0.940000] o Rx descripors: q0=128 [ 0.940000] o Tx descripors: q0=532 [ 0.950000] o Loading network interface(s): [ 0.950000] o register under mv88fx_eth platform [ 0.960000] o eth0, ifindex = 2, GbE port = 0 [ 0.960000] [ 0.960000] mvFpRuleDb (c45b2000): 1024 entries, 4096 bytes [ 0.970000] Counter=0, opIdx=6, overhead=16 [ 0.970000] Counter=1, opIdx=2, overhead=0 [ 0.980000] Counter=2, opIdx=1, overhead=18 [ 0.980000] Counter=3, opIdx=2, overhead=0 [ 0.990000] tun: Universal TUN/TAP device driver, 1.6 [ 0.990000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.000000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.010000] Scanning device for bad blocks [ 1.050000] Bad eraseblock 941 at 0x0000075a0000 [ 1.060000] Using static partition definition [ 1.070000] Creating 5 MTD partitions on "nand_mtd": [ 1.070000] 0x000000000000-0x000000200000 : "u-boot" [ 1.080000] 0x000000200000-0x000000500000 : "uImage" [ 1.080000] 0x000000500000-0x000000800000 : "uImage2" [ 1.090000] 0x000000800000-0x000001000000 : "failsafe" [ 1.090000] 0x000001000000-0x000008000000 : "root" [ 1.100000] UBI: attaching mtd4 to ubi0 [ 1.100000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 1.110000] UBI: logical eraseblock size: 126976 bytes [ 1.120000] UBI: smallest flash I/O unit: 2048 [ 1.120000] UBI: sub-page size: 512 [ 1.120000] UBI: VID header offset: 2048 (aligned 2048) [ 1.130000] UBI: data offset: 4096 [ 1.350000] UBI: attached mtd4 to ubi0 [ 1.360000] UBI: MTD device name: "root" [ 1.360000] UBI: MTD device size: 112 MiB [ 1.370000] UBI: number of good PEBs: 895 [ 1.370000] UBI: number of bad PEBs: 1 [ 1.380000] UBI: max. allowed volumes: 128 [ 1.380000] UBI: wear-leveling threshold: 4096 [ 1.390000] UBI: number of internal volumes: 1 [ 1.390000] UBI: number of user volumes: 1 [ 1.390000] UBI: available PEBs: 0 [ 1.400000] UBI: total number of reserved PEBs: 895 [ 1.400000] UBI: number of PEBs reserved for bad PEB handling: 8 [ 1.410000] UBI: max/mean erase counter: 1/0 [ 1.410000] UBI: image sequence number: 0 [ 1.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.420000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.430000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.440000] UBI: background thread "ubi_bgt0d" started, PID 451 [ 1.470000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.490000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 [ 1.490000] usb usb1: configuration #1 chosen from 1 choice [ 1.500000] hub 1-0:1.0: USB hub found [ 1.500000] hub 1-0:1.0: 1 port detected [ 1.510000] Initializing USB Mass Storage driver... [ 1.510000] usbcore: registered new interface driver usb-storage [ 1.520000] USB Mass Storage support registered. [ 1.520000] usbcore: registered new interface driver ums-datafab [ 1.530000] usbcore: registered new interface driver ums-freecom [ 1.530000] usbcore: registered new interface driver ums-jumpshot [ 1.540000] usbcore: registered new interface driver ums-sddr09 [ 1.550000] usbcore: registered new interface driver ums-sddr55 [ 1.550000] usbcore: registered new interface driver ums-usbat [ 1.560000] mice: PS/2 mouse device common for all mice [ 1.560000] i2c /dev entries driver [ 1.580000] sdhci: Secure Digital Host Controller Interface driver [ 1.580000] sdhci: Copyright(c) Pierre Ossman [ 1.590000] mmc0: mvsdio driver initialized, using GPIO 27 for card detection [ 1.600000] usbcore: registered new interface driver usbhid [ 1.600000] usbhid: v2.6:USB HID core driver [ 1.610000] TCP cubic registered [ 1.610000] NET: Registered protocol family 17 [ 1.620000] RPC: Registered udp transport module. [ 1.620000] RPC: Registered tcp transport module. [ 1.630000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.770000] UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 1.770000] UBIFS: file system size: 110723072 bytes (108128 KiB, 105 MiB, 872 LEBs) [ 1.780000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) [ 1.790000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 1.790000] UBIFS: default compressor: lzo [ 1.800000] UBIFS: reserved for root: 0 bytes (0 KiB) [ 1.800000] VFS: Mounted root (ubifs filesystem) on device 0:11. [ 1.810000] Freeing init memory: 124K [ 4.180000] eth0: link down [ 4.180000] eth0: started udhcpc (v1.16.1) started HWADDR 00 0x25 0x31 0x05 0xe8 0x12 PIP0 232 PIP1 18 cat: can't open '/etc/resolv.conf': No such file or directory route: SIOCDELRT: No such process grep: /etc/resolv.conf: No such file or directory Sending discover... [ 5.190000] eth0: link up, full duplex, speed 1 Gbps Sending discover... Sending discover... Sending select for 192.168.0.249... Lease of 192.168.0.249 obtained, lease time 86400 HWADDR 00 0x25 0x31 0x05 0xe8 0x12 PIP0 232 PIP1 18 route: SIOCDELRT: No such process modprobe: module 'vfat' not found [ 12.200000] ufsd: module license 'Commercial product' taints kernel. [ 12.210000] Disabling lock debugging due to kernel taint [ 12.240000] ufsd: driver 8.5 (NTFS4LINUX_U85_017_S[2011-08-17-16:51:48]) LBD=ON with delayalloc with ioctl loaded at bf000000 [ 12.240000] NTFS support included [ 12.240000] Hfs+/HfsX support included [ 12.240000] For 'CloudEngines_PogoPlug_2011-08-03' Loading rt3070sta.ko: [ 12.580000] rtusb init rt2870 ---> [ 12.590000] usbcore: registered new interface driver rt2870 Success Loading xce.ko: [ 12.610000] Cloud Engines XCE Init [Version: 3.1.99.12] [ 12.620000] XCE: CPU MEMORY MAP: [ 12.620000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings [ 12.630000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space [ 12.640000] XCE: -- 0xc0000000 - 0xc7ffffff ( 128 MB) Kernel direct-mapped ram [ 12.640000] XCE: -- 0xc8800000 - 0xe7ffffff ( 504 MB) Kernel vmalloc space [ 12.650000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space [ 12.660000] XCE: CPU FEATURES: [ 12.660000] XCE: -- I Cache: enabled [ 12.660000] XCE: -- D Cache: enabled [ 12.670000] XCE: -- Branch Predict: disabled [ 12.670000] XCE: -- MMU: enabled [ 12.680000] XCE: -- Alignment Abort: enabled [ 12.690000] XCE: BLPARAMS: -- Loading properties [c4bffefc]. [ 12.690000] XCE: BLPARAMS: -- MTD @ [c45c0c00]. [ 12.700000] XCE: BLPARAMS: Locating parameter block... [ 12.700000] XCE: BLPARAMS: reading 2048 bytes @ a0000 [ 12.710000] XCE: Loaded Property Size: 2048 [ 12.710000] XCE: - 'cesvcid' -> 'GL6SYKKSQE7BBS9MC67LB9LBMJ' [ 12.720000] XCE: - 'ceboardver' -> 'PPV4A1' [ 12.720000] XCE: -- ICache Prefetch: enabled [ 12.730000] XCE: -- DCache Prefetch: enabled [ 12.730000] XCE: -- L2 Cache: enabled [ 12.740000] XCE: -- L2 Prefetch: disabled [ 12.740000] XCE: -- L2 Writethrough: disabled [ 12.750000] XCE: -- Write Allocate: disabled [ 12.750000] XCE: -- Streaming: disabled [ 12.760000] XCE: Current GPIO State: [ 12.760000] XCE: GPIO L OUT: 0x01e18400 [ 12.760000] XCE: GPIO L OE: 0xfe004800 [ 12.770000] XCE: GPIO L BLINK: 0x00000000 [ 12.770000] XCE: GPIO L POL: 0x08000000 [ 12.780000] XCE: GPIO L IN: 0x11e00000 [ 12.780000] XCE: GPIO H OUT: 0x00000008 [ 12.780000] XCE: GPIO H OE: 0x00000005 [ 12.790000] XCE: GPIO H BLINK: 0x00000000 [ 12.790000] XCE: GPIO H POL: 0x00000000 [ 12.800000] XCE: GPIO H IN: 0x00000008 Success Starting hbplug: Success / # [ 12.890000] XCE: BLPARAMS: -- Loading properties [c4bffecc]. [ 12.890000] XCE: BLPARAMS: -- MTD @ [c45c0c00]. [ 12.900000] XCE: BLPARAMS: Locating parameter block... [ 12.900000] XCE: BLPARAMS: reading 2048 bytes @ a0000 [ 12.910000] XCE: BLPARAMS: reading 2048 bytes @ a0800 [ 12.910000] XCE: BLPARAMS: reading 2048 bytes @ a1000 [ 12.920000] XCE: BLPARAMS: reading 2048 bytes @ a1800 [ 18.170000] XCE: XCE: LED -> DISCONNECTED
|
Re: Pogoplug Wont Accept Commands after interrupt January 26, 2019 12:25AM |
Registered: 6 years ago Posts: 4 |
U-Boot 1.1.4 (Oct 1 2011 - 12:21:35) Clou$ Engines 1.1.2 (3.4.27) PHYADDR=0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006918B4 Soc: 88F6192 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:5128 MB 55Flash: 0 kB CPU : Marvell Feroceon (Rev 1) 5CLOUD ENGINES BOARD: PPV4A1 5 Streaming disabled Write allocate disabled USB 0: host mode 55PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 CE>> printenv
|
Re: Pogoplug Wont Accept Commands after interrupt January 26, 2019 09:02AM |
Admin Registered: 14 years ago Posts: 19,548 |
> U-Boot 1.1.4 (Oct 1 2011 - 12:21:35) Clou$ > Engines 1.1.2 (3.4.27) PHYADDR=0 > > U-Boot code: 00600000 -> 0067FFF0 BSS: -> > 006918B4 > > Soc: 88F6192 A1 (DDR2) > CPU running @ 800Mhz L2 running @ 400Mhz > SysClock = 200Mhz , TClock = 166Mhz > > DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 > DRAM CS[0] base 0x00000000 size 128MB > DRAM Total size 128MB 16bit width > Addresses 8M - 0M are saved for the U-Boot usage. > Mem malloc Initialization (8M - 7M): Done > NAND:5128 MB > 55Flash: 0 kB > > CPU : Marvell Feroceon (Rev 1) > 5CLOUD ENGINES BOARD: PPV4A1 > 5 > Streaming disabled > Write allocate disabled > > > USB 0: host mode > 55PEX 0: interface detected no Link. > Net: egiga0 [PRIME] > Hit any key to stop autoboot: 0 > CE>> printenv >
|
Re: Pogoplug Wont Accept Commands after interrupt January 26, 2019 01:54PM |
Registered: 6 years ago Posts: 4 |
|
Re: Pogoplug Wont Accept Commands after interrupt January 26, 2019 06:03PM |
Registered: 6 years ago Posts: 4 |