Need help fixing my GoFlex Home May 22, 2012 08:38PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home May 22, 2012 08:53PM |
Registered: 12 years ago Posts: 501 |
Re: Need help fixing my GoFlex Home May 22, 2012 09:14PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home May 22, 2012 09:42PM |
Registered: 12 years ago Posts: 501 |
Re: Need help fixing my GoFlex Home May 22, 2012 10:08PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home May 22, 2012 10:22PM |
Registered: 12 years ago Posts: 501 |
Re: Need help fixing my GoFlex Home May 23, 2012 12:02AM |
Admin Registered: 13 years ago Posts: 18,570 |
Re: Need help fixing my GoFlex Home May 23, 2012 09:42PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home May 24, 2012 05:22PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home May 24, 2012 05:29PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home May 30, 2012 08:40PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home May 30, 2012 09:31PM |
Registered: 12 years ago Posts: 501 |
Re: Need help fixing my GoFlex Home May 30, 2012 11:45PM |
Admin Registered: 13 years ago Posts: 18,570 |
Re: Need help fixing my GoFlex Home May 31, 2012 06:53AM |
Registered: 11 years ago Posts: 92 |
rescue:/# fw_printenv arcNumber=3089 baudrate=115200 bootcmd=run bootcmd_usb; usb stop; run bootcmd_pogo; reset bootcmd_usb=run usb_init; run usb_load_uimage; run set_bootargs_usb; run usb_boot; bootdelay=3 console=ttyS0,115200 ethact=egiga0 ethaddr=XXXXXXXXX led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts stderr=serial stdin=serial stdout=serial usb_boot=if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000;else bootm 0x800000;fi; usb_device=0:1 usb_init=usb start usb_load_uimage=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext2 set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000 bootcmd_pogo=run bootcmd_rescue rescue_installed=1
Re: Need help fixing my GoFlex Home June 01, 2012 02:18AM |
Admin Registered: 13 years ago Posts: 18,570 |
1. Set the label of the USB drive to "rootfs": Boot into the rescue system, or use another Linux box, set the rootfs label for the USB drive (assuming the USB drive is assigned sda1, if it's assigned different drive letter then use it) # tune2fs -L rootfs /dev/sda1 2. Use the USB drive, boot up the GF Home, and set the booting environment variable usb_init to (see comment below, you have to change this): # fw_setenv usb_init "run usb_scan; setenv usb_root LABEL=rootfs" 3. Shutdown the GFHome. 4. Plug in both drives and boot up. The HDD will be assigned sda1 and the USB will be assigned sdb1. UBoot will find the correct boot drive because the USB drive has label "rootfs".
Re: Need help fixing my GoFlex Home June 01, 2012 03:09PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home June 02, 2012 09:54AM |
Registered: 11 years ago Posts: 92 |
arcNumber=3089 baudrate=115200 bootcmd_usb=run usb_init; run usb_load_uimage; run set_bootargs_usb; run usb_boot; bootdelay=3 console=ttyS0,115200 ethact=egiga0 ethaddr=XXXXXXXXXX led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts stderr=serial stdin=serial stdout=serial usb_boot=if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000;else bootm 0x800000;fi; usb_device=0:1 usb_load_uimage=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext2 set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000 bootcmd_pogo=run bootcmd_rescue rescue_installed=1 serverip=192.168.1.119 usb_init=usb start; setenv usb_root LABEL=rootfs sata_init=ide reset sata_root=/dev/sda1 sata_rootfstype=ext2 bootcmd_sata=run sata_init; run sata_load_uimage; run set_bootargs_sata; run sata_boot; set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$sata_rootdelay rootfstype=$sata_rootfstype $mtdparts sata_rootdelay=8 sata_device=0:1 sata_boot=if ext2load ide $sata_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000;else bootm 0x800000;fi; bootcmd=run bootcmd_usb; usb stop; run bootcmd_sata; run bootcmd_pogo; reset sata_load_uimage=mw 0x800000 0 1; ext2load ide $sata_device 0x800000 /boot/uImage
Re: Need help fixing my GoFlex Home June 02, 2012 09:59AM |
Registered: 12 years ago Posts: 501 |
Re: Need help fixing my GoFlex Home June 02, 2012 10:17AM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home June 02, 2012 11:09AM |
Registered: 12 years ago Posts: 501 |
mkswap /dev/sda2
Re: Need help fixing my GoFlex Home June 02, 2012 12:15PM |
Registered: 11 years ago Posts: 92 |
Re: Need help fixing my GoFlex Home June 02, 2012 12:32PM |
Registered: 12 years ago Posts: 501 |