Help! Akitio mycloudmini using stock kernel but missing system setting files November 20, 2023 08:22AM |
Registered: 9 months ago Posts: 82 |
Stage-1 Bootloader 一 8月 30 10:55:36 CST 2010 Attempting to set PLLA to 700MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000E0000 plla_ctrl2 : 0x001B01A0 plla_ctrl3 : 0x00000016 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A0D8 Hdr CRC: 0x330E1A94 OK U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 $ $ printenv bootcmd=run extinguishled boot_nand bootdelay=2 baudrate=115200 ethaddr=00:30:e0:00:00:01 ipaddr=172.31.0.128 serverip=172.31.0.100 autoload=n netmask=255.255.0.0 bootfile="uImage" load_nand=nboot 60500000 0 440000 load_nand2=nboot 60500000 0 A40000 lightled=ledfail 1 extinguishled=ledfail 0 boot=bootm 60500000 boot_nand=run load_nand boot || run load_nand2 boot || run lightled stdin=serial stdout=serial stderr=serial bootargs=root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes Environment size: 576/8188 bytes setenv bootargs ${bootargs} single init=/bin/sh && reset $ printenv Unknown command 'printenv' - try 'help' $ printenv bootcmd=run extinguishled boot_nand bootdelay=2 baudrate=115200 ethaddr=00:30:e0:00:00:01 ipaddr=172.31.0.128 serverip=172.31.0.100 autoload=n netmask=255.255.0.0 bootfile="uImage" load_nand=nboot 60500000 0 440000 load_nand2=nboot 60500000 0 A40000 lightled=ledfail 1 extinguishled=ledfail 0 boot=bootm 60500000 boot_nand=run load_nand boot || run load_nand2 boot || run lightled stdin=serial stdout=serial stderr=serial bootargs=root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes single init=/bin/sh Environment size: 596/8188 bytes $ boot Unknown command 'boot' - try 'help' $ boot Unknown command 'boot' - try 'help' $ help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol cmp - memory compare cp - memory copy crc32 - checksum calculation echo - echo args to console exit - exit script fg - flash gpio <port 0 , 1 > <gpio pin [17:0] > <times> go - start application at address 'addr' help - print online help iminfo - print header information for application image ledfail - Extinguish (0) or light (1) failure LED loop - infinite loop on address range md - memory display mm - memory modify (auto-incrementing) mtest - simple RAM test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nm - memory modify (constant address) nwboot - NAND Write boot information otp - OTP sub-system ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable setenv - set environment variables sg - set gpio <port 0 , 1 > <gpio pin [17:0] > < (1) high (0) low> test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol version - print monitor version $ version U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) $ reset Resetting...
Stage-1 Bootloader 一 8月 30 10:55:36 CST 2010 Attempting to set PLLA to 700MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000E0000 plla_ctrl2 : 0x001B01A0 plla_ctrl3 : 0x00000016 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A0D8 Hdr CRC: 0x330E1A94 OK U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 $ printenv bootargs bootargs=root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes $ setenv bootargs "XXXXX single init=/bin/sh" $ print bootcmd=run extinguishled boot_nand bootdelay=2 baudrate=115200 ethaddr=00:30:e0:00:00:01 ipaddr=172.31.0.128 serverip=172.31.0.100 autoload=n netmask=255.255.0.0 bootfile="uImage" load_nand=nboot 60500000 0 440000 load_nand2=nboot 60500000 0 A40000 lightled=ledfail 1 extinguishled=ledfail 0 boot=bootm 60500000 boot_nand=run load_nand boot || run load_nand2 boot || run lightled stdin=serial stdout=serial stderr=serial bootargs=XXXXX single init=/bin/sh Environment size: 457/8188 bytes $
Stage-1 Bootloader 一 8月 30 10:55:36 CST 2010 Attempting to set PLLA to 700MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000E0000 plla_ctrl2 : 0x001B01A0 plla_ctrl3 : 0x00000016 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A0D8 Hdr CRC: 0x330E1A94 OK U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 Extinguish LED Loading from device 0: 256MiB 3,3V 8-bit (offset 0x440000) Image Name: Linux-2.6.31.6-fast-20110114 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3056816 Bytes = 2.9 MB Load Address: 60008000 Entry Point: 60008000 ## Booting image at 60500000 ... Image Name: Linux-2.6.31.6-fast-20110114 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3056816 Bytes = 2.9 MB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................................................................................................................... done, booting the kernel. Linux version 2.6.31.6-fast-20110114 (thom@11z) (gcc version 4.5.1 (GCC) ) #1 SMP Fri Jan 14 13:58:20 CST 2011 CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Oxsemi NAS 1 memory region Ignoring unrecognised tag 0x00000000 Memory policy: ECC disabled, Data cache writealloc Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes PID hash table entries: 1024 (order: 10, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB = 256MB total Memory: 253696KB available (5260K code, 310K data, 136K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. NR_IRQS:96 OX820_RPS_init_irq: interrupts 64 to 96 Console: colour dummy device 80x30 console [ttyS0] enabled Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736) Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Calibrating local timer... 349.98MHz. CPU1: Booted secondary processor Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736) Brought up 2 CPUs SMP: Total of 2 processors activated (558.69 BogoMIPS). NET: Registered protocol family 16 Number of DMA channels = 4, version = 4 Reserving a DMA channel for DirectRAID Allocating 218 SRAM generic DMA descriptors bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Calling CRDA to update world regulatory domain NET: Registered protocol family 2 Switched to NOHz mode on CPU #0 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) Switched to NOHz mode on CPU #1 TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 Create fragment cache fuse init (API version 7.12) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 496 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A brd: module loaded loop: module loaded ox820sata: OX820 sata core. scsi0 : oxnassata scsi1 : oxnassata ata1: SATA max UDMA/133 irq 50 ata2: SATA max UDMA/133 irq 50 ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x000000000000-0x0000026c0000 : "Boot partition" 0x0000026c0000-0x000010000000 : "Data Partition" UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI warning: ubi_eba_init_scan: cannot reserve enough PEBs for bad PEB handling, reserved 11, need 17 UBI: attached mtd2 to ubi0 UBI: MTD device name: "Data Partition" UBI: MTD device size: 217 MiB UBI: number of good PEBs: 1738 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 1738 UBI: number of PEBs reserved for bad PEB handling: 11 UBI: max/mean erase counter: 800/105 UBI: image sequence number: 1359814330 UBI: background thread "ubi_bgt0d" started, PID 398 Probing for Synopsis GMAC, unit 0 eth0: use mtd hwaddr eth0: Tuning GMAC 0 RGMII timings eth0: PHY is Realtek RTL8211D, type 0x001cc914 eth0: GMAC ver = 53, vendor ver = 18 at 0xe1400000, IRQ 40 eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000 eth0: Ethernet addr: 00:01:d2:12:00:fa probe() eth0: Leon x2 clock tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Start USB clocks oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1 oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000 oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice IRQ 53 uses trigger mode 0; requested 3 input: gpio-keys as /devices/platform/gpio-keys/input/input0 irq 54: nobody cared (try booting with the "irqpoll" option) [<c002fab0>] (unwind_backtrace+0x0/0xe0) from [<c0076430>] (__report_bad_irq+0x78/0xa8) [<c0076430>] (__report_bad_irq+0x78/0xa8) from [<c00765e4>] (note_interrupt+0x184/0x1f0) [<c00765e4>] (note_interrupt+0x184/0x1f0) from [<c0076b44>] (handle_level_irq+0x108/0x130) [<c0076b44>] (handle_level_irq+0x108/0x130) from [<c002a054>] (asm_do_IRQ+0x54/0xa8) [<c002a054>] (asm_do_IRQ+0x54/0xa8) from [<c002abd8>] (__irq_svc+0x38/0xc0) Exception stack(0xcf813b48 to 0xcf813b90) 3b40: cf813b90 ffff8bf5 00000000 00000000 00000102 c0593ac0 3b60: cf812000 cf812000 c0023530 c056e040 c05a1d60 00000000 00000002 cf813b90 3b80: c0050b8c c00506e8 20000113 ffffffff [<c002abd8>] (__irq_svc+0x38/0xc0) from [<c00506e8>] (__do_softirq+0x50/0x140) [<c00506e8>] (__do_softirq+0x50/0x140) from [<c0050b8c>] (irq_exit+0x84/0xa0) [<c0050b8c>] (irq_exit+0x84/0xa0) from [<c002a058>] (asm_do_IRQ+0x58/0xa8) [<c002a058>] (asm_do_IRQ+0x58/0xa8) from [<c002abd8>] (__irq_svc+0x38/0xc0) Exception stack(0xcf813be8 to 0xcf813c30) 3be0: c059437c 60000013 e510001c 00000000 00000000 e510001c 3c00: c0573454 00000000 00000029 60000013 00000000 cf813d94 e500001c cf813c30 3c20: c0034b58 c03eec80 20000013 ffffffff [<c002abd8>] (__irq_svc+0x38/0xc0) from [<c03eec80>] (_spin_unlock_irqrestore+0x18/0x1c) [<c03eec80>] (_spin_unlock_irqrestore+0x18/0x1c) from [<c0034b58>] (ox820_gpio_direction_output+0x60/0xa8) [<c0034b58>] (ox820_gpio_direction_output+0x60/0xa8) from [<c0257c64>] (gpio_direction_output+0xcc/0xf0) [<c0257c64>] (gpio_direction_output+0xcc/0xf0) from [<c02e7ce8>] (i2c_start+0x18/0x44) [<c02e7ce8>] (i2c_start+0x18/0x44) from [<c02e83b4>] (bit_xfer+0x24/0x4b0) [<c02e83b4>] (bit_xfer+0x24/0x4b0) from [<c02e5ff8>] (i2c_transfer+0xb0/0xf0) [<c02e5ff8>] (i2c_transfer+0xb0/0xf0) from [<c02e62c8>] (i2c_smbus_xfer+0x290/0x54c) [<c02e62c8>] (i2c_smbus_xfer+0x290/0x54c) from [<c02e6624>] (i2c_smbus_read_i2c_block_data+0x4c/0x74) [<c02e6624>] (i2c_smbus_read_i2c_block_data+0x4c/0x74) from [<c03eb914>] (ds1307_probe+0x350/0x608) [<c03eb914>] (ds1307_probe+0x350/0x608) from [<c02e5e10>] (i2c_device_probe+0x6c/0x84) [<c02e5e10>] (i2c_device_probe+0x6c/0x84) from [<c027adac>] (driver_probe_device+0x78/0x164) [<c027adac>] (driver_probe_device+0x78/0x164) from [<c0279e1c>] (bus_for_each_drv+0x60/0x8c) [<c0279e1c>] (bus_for_each_drv+0x60/0x8c) from [<c027ac60>] (device_attach+0x70/0x88) [<c027ac60>] (device_attach+0x70/0x88) from [<c027a650>] (bus_probe_device+0x24/0x44) [<c027a650>] (bus_probe_device+0x24/0x44) from [<c0278a50>] (device_add+0x3d0/0x4b4) [<c0278a50>] (device_add+0x3d0/0x4b4) from [<c02e6fb0>] (i2c_new_device+0xbc/0x124) [<c02e6fb0>] (i2c_new_device+0xbc/0x124) from [<c02e7a10>] (i2c_register_adapter+0x124/0x1a8) [<c02e7a10>] (i2c_register_adapter+0x124/0x1a8) from [<c02e7b44>] (i2c_add_numbered_adapter+0xb0/0xc8) [<c02e7b44>] (i2c_add_numbered_adapter+0xb0/0xc8) from [<c03ebd50>] (i2c_gpio_probe+0x184/0x244) [<c03ebd50>] (i2c_gpio_probe+0x184/0x244) from [<c027bb20>] (platform_drv_probe+0x18/0x1c) [<c027bb20>] (platform_drv_probe+0x18/0x1c) from [<c027adac>] (driver_probe_device+0x78/0x164) [<c027adac>] (driver_probe_device+0x78/0x164) from [<c027af24>] (__driver_attach+0x8c/0x90) [<c027af24>] (__driver_attach+0x8c/0x90) from [<c027a0e4>] (bus_for_each_dev+0x54/0x80) [<c027a0e4>] (bus_for_each_dev+0x54/0x80) from [<c027a78c>] (bus_add_driver+0x98/0x230) [<c027a78c>] (bus_add_driver+0x98/0x230) from [<c027b14c>] (driver_register+0x78/0x13c) [<c027b14c>] (driver_register+0x78/0x13c) from [<c001ca50>] (i2c_gpio_init+0xc/0x30) [<c001ca50>] (i2c_gpio_init+0xc/0x30) from [<c002a5b8>] (do_one_initcall+0x30/0x1a0) [<c002a5b8>] (do_one_initcall+0x30/0x1a0) from [<c0008bf8>] (kernel_init+0x16c/0x1f8) [<c0008bf8>] (kernel_init+0x16c/0x1f8) from [<c002bad8>] (kernel_thread_exit+0x0/0x8) handlers: [<c02e3210>] (gpio_keys_isr+0x0/0x8c) Disabling IRQ #54 rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0 i2c-gpio i2c-gpio.0: using pins 41 (SDA) and 42 (SCL) md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 Registered led device: hddaerr Registered led device: hddberr Registered led device: system Registered led device: firmware Registered led device: usbcopy TCP cubic registered NET: Registered protocol family 10 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc-ds1307 0-0068: setting system clock to 2023-11-19 20:42:42 UTC (1700426562) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: file system size: 220502016 bytes (215334 KiB, 210 MiB, 1709 LEBs) UBIFS: journal size: 9033728 bytes (8822 KiB, 8 MiB, 71 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 0 bytes (0 KiB) VFS: Mounted root (ubifs filesystem) on device 0:10. Freeing init memory: 136K Welcome to Fedora Press 'I' to enter interactive startup. Starting udev: /bin/chown: invalid user: `root:disk' /bin/chown: invalid user: `root:disk' /bin/chown: invalid user: `root:disk' /bin/chown: invalid user: `root:disk' /bin/chown: invalid user: `root:disk' /bin/chown: invalid user: `root:disk' /bin/chown: invalid user: `root:disk' /bin/chown: invalid user: `root:disk' /bin/chown: invalid user: `root:lp' /bin/chown: invalid user: `root:lp' /bin/chown: invalid user: `root:lp' /bin/chown: invalid user: `root:lp' [ OK ] Setting hostname localhost: [ OK ] Checking filesystems WARNING: couldn't open /etc/fstab: No such file or directory Checking all file systems. [ OK ] warning: can't open /etc/fstab: No such file or directory mount: can't find / in /etc/fstab or /etc/mtab Mounting local filesystems: warning: can't open /etc/fstab: No such file or directory [ OK ] chown: invalid user: `root:root' Enabling /etc/fstab swaps: swapon: /etc/fstab: open failed: No such file or directory [FAILED] ** (process:699): WARNING **: Couldn't create log file /var/log/ConsoleKit/history (No such file or directory) init: ck-log-system-start main process (699) terminated with status 1 Entering non-interactive startup Scan raid infomation: mdadm: No arrays found in config file or automatically Restoring /var/log to tmpfs: mount tmpfs on /var/log... extract backup logs to /var/log... 10 blocks error: bad top line in state file /var/lib/logrotate.status error: could not read state file, will not attempt to write into it error: bad top line in state file /var/lib/logrotate.status error: could not read state file, will not attempt to write into it Starting portreserve: [ OK ] Starting system logger: [ OK ] Starting system message bus: Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown username "avahi" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown username "root" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown group "avahi" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown username "root" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown username "root" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown username "root" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown username "root" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown username "root" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Unknown username "root" in message bus configuration file Could not get password database information for UID of current process: User "???" unknown or no memory to allocate password entry Failed to start message bus: Could not get UID and GID for username "dbus" [FAILED] /etc/rc3.d/S24avahi-daemon: line 40: /etc/sysconfig/network: No such file or directory Starting cups: [ OK ] Retrigger failed udev events[ OK ] Starting xinetd: [ OK ] /etc/rc3.d/S57ntpdate: line 18: /etc/sysconfig/network: No such file or directory NTP server not specified in /etc/ntp/step-tickers or /etc/ntp.conf /etc/rc3.d/S58ntpd: line 29: /etc/sysconfig/network: No such file or directory Starting ntpd: [ OK ] /etc/rc3.d/S60nas: line 28: /etc/sysconfig/network: No such file or directory Starting NAS (nas): fastcgi buttons diskmon Starting lighttpd: 2023-11-19 20:42:56: (server.c.756) can't find username lighttpd [FAILED] [FAILED] atd: [FAILED] swapon: /etc/fstab: open failed: No such file or directory Starting NAS LED (nasled): sqlite3: cannot locate your home directory! product was "akitio" nas-service/etc/rc3.d/S99nasled: line 83: /etc/nas/spindown: No such file or directory Starting smartd: [ OK ] Fedora release 12 (Constantine) Kernel 2.6.31.6-fast-20110114 on an armv6l (/dev/ttyS0) localhost login:
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 20, 2023 11:01AM |
Registered: 9 months ago Posts: 82 |
U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 $ ping 172.31.0.100 Wait GMAC to reset Wait for PHY reset Ethernet Phy not recognised! Wait for link to come up..Link up Wait for auto-negotiation to complete.........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Stage-1 Bootloader 一 8月 30 10:55:36 CST 2010 Attempting to set PLLA to 700MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000E0000 plla_ctrl2 : 0x001B01A0 plla_ctrl3 : 0x00000016 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A0D8 Hdr CRC: 0x330E1A94 OK U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 $ ping 172.31.0.100 Wait GMAC to reset Wait for PHY reset Ethernet Phy not recognised! Wait for link to come up...........Link up Wait for auto-negotiation to complete........................................................................................................................................................................................................................................................................Stage-1 Bootloader 一 8月 30 10:55:36 CST 2010 Attempting to set PLLA to 700MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000E0000 plla_ctrl2 : 0x001B01A0 plla_ctrl3 : 0x00000016 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A0D8 Hdr CRC: 0x330E1A94 OK U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 $ tftpboot Wait GMAC to reset Wait for PHY reset Ethernet Phy not recognised! Wait for link to come up.Link up Wait for auto-negotiation to complete........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Stage-1 Bootloader 一 8月 30 10:55:36 CST 2010 Attempting to set PLLA to 700MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000E0000 plla_ctrl2 : 0x001B01A0 plla_ctrl3 : 0x00000016 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A0D8 Hdr CRC: 0x330E1A94 OK U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 $ iminfo ## Checking Image at 60000000 ... Bad Magic Number $ help iminfo iminfo addr [addr ...] - print header information for application image starting at address 'addr' in memory; this includes verification of the image conte' - try 'help'ber, header and payload checksums) $ $ helpn command ' ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol cmp - memory compare cp - memory copy crc32 - checksum calculation echo - echo args to console exit - exit script fg - flash gpio <port 0 , 1 > <gpio pin [17:0] > <times> go - start application at address 'addr' help - print online help iminfo - print header information for application image ledfail - Extinguish (0) or light (1) failure LED loop - infinite loop on address range md - memory display mm - memory modify (auto-incrementing) mtest - simple RAM test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nm - memory modify (constant address) nwboot - NAND Write boot information otp - OTP sub-system ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable setenv - set environment variables sg - set gpio <port 0 , 1 > <gpio pin [17:0] > < (1) high (0) low> test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol version - print monitor version $ baSE Unknown command 'baSE' - try 'help' $ base Base Address: 0x00000000 $ bdinfo arch_number = 0x00000480 env_t = 0x00000000 boot_params = 0x60000100 DRAM bank = 0x00000000 -> start = 0x60000000 -> size = 0x10000000 ethaddr = 00:30:E0:00:00:01 ip_addr = 172.31.0.128 baudrate = 115200 bps $ ping 172.31.0.128 Wait GMAC to reset Wait for PHY reset Ethernet Phy not recognised! Wait for link to come up.............Link up Wait for auto-negotiation to complete...........................................................................................................................................................................................................................................................................................................................................................................
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 20, 2023 12:50PM |
Registered: 9 months ago Posts: 82 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 20, 2023 01:01PM |
Registered: 9 months ago Posts: 82 |
U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 Extinguish LED Loading from device 0: 256MiB 3,3V 8-bit (offset 0x440000) Image Name: Linux-2.6.31.6-fast-20110114 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3056816 Bytes = 2.9 MB Load Address: 60008000 Entry Point: 60008000 ## Booting image at 60500000 ... Image Name: Linux-2.6.31.6-fast-20110114 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3056816 Bytes = 2.9 MB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................................................................................................................... done, booting the kernel. Linux version 2.6.31.6-fast-20110114 (thom@11z) (gcc version 4.5.1 (GCC) ) #1 SMP Fri Jan 14 13:58:20 CST 2011 CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Oxsemi NAS 1 memory region Ignoring unrecognised tag 0x00000000 Memory policy: ECC disabled, Data cache writealloc Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes PID hash table entries: 1024 (order: 10, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB = 256MB total Memory: 253696KB available (5260K code, 310K data, 136K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. NR_IRQS:96 OX820_RPS_init_irq: interrupts 64 to 96 Console: colour dummy device 80x30 console [ttyS0] enabled Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736) Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Calibrating local timer... 349.98MHz. CPU1: Booted secondary processor Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736) Brought up 2 CPUs SMP: Total of 2 processors activated (558.69 BogoMIPS). NET: Registered protocol family 16 Number of DMA channels = 4, version = 4 Reserving a DMA channel for DirectRAID Allocating 218 SRAM generic DMA descriptors bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Calling CRDA to update world regulatory domain NET: Registered protocol family 2 Switched to NOHz mode on CPU #0 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) Switched to NOHz mode on CPU #1 TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 Create fragment cache fuse init (API version 7.12) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 496 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A brd: module loaded loop: module loaded ox820sata: OX820 sata core. scsi0 : oxnassata scsi1 : oxnassata ata1: SATA max UDMA/133 irq 50 ata2: SATA max UDMA/133 irq 50 ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x000000000000-0x0000026c0000 : "Boot partition" 0x0000026c0000-0x000010000000 : "Data Partition" UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI warning: ubi_eba_init_scan: cannot reserve enough PEBs for bad PEB handling, reserved 11, need 17 UBI: attached mtd2 to ubi0 UBI: MTD device name: "Data Partition" UBI: MTD device size: 217 MiB UBI: number of good PEBs: 1738 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 1738 UBI: number of PEBs reserved for bad PEB handling: 11 UBI: max/mean erase counter: 800/105 UBI: image sequence number: 1359814330 UBI: background thread "ubi_bgt0d" started, PID 398 Probing for Synopsis GMAC, unit 0 eth0: use mtd hwaddr eth0: Tuning GMAC 0 RGMII timings eth0: PHY is Realtek RTL8211D, type 0x001cc914 eth0: GMAC ver = 53, vendor ver = 18 at 0xe1400000, IRQ 40 eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000 eth0: Ethernet addr: 00:01:d2:12:00:fa probe() eth0: Leon x2 clock tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Start USB clocks oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1 oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000 oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice IRQ 53 uses trigger mode 0; requested 3 input: gpio-keys as /devices/platform/gpio-keys/input/input0 irq 54: nobody cared (try booting with the "irqpoll" option) [<c002fab0>] (unwind_backtrace+0x0/0xe0) from [<c0076430>] (__report_bad_irq+0x78/0xa8) [<c0076430>] (__report_bad_irq+0x78/0xa8) from [<c00765e4>] (note_interrupt+0x184/0x1f0) [<c00765e4>] (note_interrupt+0x184/0x1f0) from [<c0076b44>] (handle_level_irq+0x108/0x130) [<c0076b44>] (handle_level_irq+0x108/0x130) from [<c002a054>] (asm_do_IRQ+0x54/0xa8) [<c002a054>] (asm_do_IRQ+0x54/0xa8) from [<c002abd8>] (__irq_svc+0x38/0xc0) Exception stack(0xcf813b48 to 0xcf813b90) 3b40: cf813b90 00000005 00000000 00000000 00000102 c0593ac0 3b60: cf812000 00000000 c0023530 c056e040 c05a1d60 00000000 00354dc9 cf813b90 3b80: c0050b8c c00506e8 20000113 ffffffff [<c002abd8>] (__irq_svc+0x38/0xc0) from [<c00506e8>] (__do_softirq+0x50/0x140) [<c00506e8>] (__do_softirq+0x50/0x140) from [<c0050b8c>] (irq_exit+0x84/0xa0) [<c0050b8c>] (irq_exit+0x84/0xa0) from [<c002a258>] (do_local_timer+0x54/0x70) [<c002a258>] (do_local_timer+0x54/0x70) from [<c002abd8>] (__irq_svc+0x38/0xc0) Exception stack(0xcf813be8 to 0xcf813c30) 3be0: c059437c 60000013 e510001c 00000000 00000000 e510001c 3c00: c0573454 00000000 00000029 60000013 00000000 cf813d94 e500001c cf813c30 3c20: c0034b58 c03eec80 20000013 ffffffff [<c002abd8>] (__irq_svc+0x38/0xc0) from [<c03eec80>] (_spin_unlock_irqrestore+0x18/0x1c) [<c03eec80>] (_spin_unlock_irqrestore+0x18/0x1c) from [<c0034b58>] (ox820_gpio_direction_output+0x60/0xa8) [<c0034b58>] (ox820_gpio_direction_output+0x60/0xa8) from [<c0257c64>] (gpio_direction_output+0xcc/0xf0) [<c0257c64>] (gpio_direction_output+0xcc/0xf0) from [<c02e7ce8>] (i2c_start+0x18/0x44) [<c02e7ce8>] (i2c_start+0x18/0x44) from [<c02e83b4>] (bit_xfer+0x24/0x4b0) [<c02e83b4>] (bit_xfer+0x24/0x4b0) from [<c02e5ff8>] (i2c_transfer+0xb0/0xf0) [<c02e5ff8>] (i2c_transfer+0xb0/0xf0) from [<c02e62c8>] (i2c_smbus_xfer+0x290/0x54c) [<c02e62c8>] (i2c_smbus_xfer+0x290/0x54c) from [<c02e6624>] (i2c_smbus_read_i2c_block_data+0x4c/0x74) [<c02e6624>] (i2c_smbus_read_i2c_block_data+0x4c/0x74) from [<c03eb914>] (ds1307_probe+0x350/0x608) [<c03eb914>] (ds1307_probe+0x350/0x608) from [<c02e5e10>] (i2c_device_probe+0x6c/0x84) [<c02e5e10>] (i2c_device_probe+0x6c/0x84) from [<c027adac>] (driver_probe_device+0x78/0x164) [<c027adac>] (driver_probe_device+0x78/0x164) from [<c0279e1c>] (bus_for_each_drv+0x60/0x8c) [<c0279e1c>] (bus_for_each_drv+0x60/0x8c) from [<c027ac60>] (device_attach+0x70/0x88) [<c027ac60>] (device_attach+0x70/0x88) from [<c027a650>] (bus_probe_device+0x24/0x44) [<c027a650>] (bus_probe_device+0x24/0x44) from [<c0278a50>] (device_add+0x3d0/0x4b4) [<c0278a50>] (device_add+0x3d0/0x4b4) from [<c02e6fb0>] (i2c_new_device+0xbc/0x124) [<c02e6fb0>] (i2c_new_device+0xbc/0x124) from [<c02e7a10>] (i2c_register_adapter+0x124/0x1a8) [<c02e7a10>] (i2c_register_adapter+0x124/0x1a8) from [<c02e7b44>] (i2c_add_numbered_adapter+0xb0/0xc8) [<c02e7b44>] (i2c_add_numbered_adapter+0xb0/0xc8) from [<c03ebd50>] (i2c_gpio_probe+0x184/0x244) [<c03ebd50>] (i2c_gpio_probe+0x184/0x244) from [<c027bb20>] (platform_drv_probe+0x18/0x1c) [<c027bb20>] (platform_drv_probe+0x18/0x1c) from [<c027adac>] (driver_probe_device+0x78/0x164) [<c027adac>] (driver_probe_device+0x78/0x164) from [<c027af24>] (__driver_attach+0x8c/0x90) [<c027af24>] (__driver_attach+0x8c/0x90) from [<c027a0e4>] (bus_for_each_dev+0x54/0x80) [<c027a0e4>] (bus_for_each_dev+0x54/0x80) from [<c027a78c>] (bus_add_driver+0x98/0x230) [<c027a78c>] (bus_add_driver+0x98/0x230) from [<c027b14c>] (driver_register+0x78/0x13c) [<c027b14c>] (driver_register+0x78/0x13c) from [<c001ca50>] (i2c_gpio_init+0xc/0x30) [<c001ca50>] (i2c_gpio_init+0xc/0x30) from [<c002a5b8>] (do_one_initcall+0x30/0x1a0) [<c002a5b8>] (do_one_initcall+0x30/0x1a0) from [<c0008bf8>] (kernel_init+0x16c/0x1f8) [<c0008bf8>] (kernel_init+0x16c/0x1f8) from [<c002bad8>] (kernel_thread_exit+0x0/0x8) handlers: [<c02e3210>] (gpio_keys_isr+0x0/0x8c) Disabling IRQ #54 rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0 i2c-gpio i2c-gpio.0: using pins 41 (SDA) and 42 (SCL) md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 Registered led device: hddaerr Registered led device: hddberr Registered led device: system Registered led device: firmware Registered led device: usbcopy TCP cubic registered NET: Registered protocol family 10 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc-ds1307 0-0068: setting system clock to 2023-11-20 18:53:07 UTC (1700506387) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: file system size: 220502016 bytes (215334 KiB, 210 MiB, 1709 LEBs) UBIFS: journal size: 9033728 bytes (8822 KiB, 8 MiB, 71 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 0 bytes (0 KiB) VFS: Mounted root (ubifs filesystem) on device 0:10. Freeing init memory: 136K Welcome to Fedora Press 'I' to enter interactive startup. Starting udev: [ OK ] Setting hostname iSharing: [ OK ] Checking filesystems WARNING: couldn't open /etc/fstab: No such file or directory Checking all file systems. [ OK ] warning: can't open /etc/fstab: No such file or directory mount: can't find / in /etc/fstab or /etc/mtab Mounting local filesystems: warning: can't open /etc/fstab: No such file or directory [ OK ] Enabling /etc/fstab swaps: swapon: /etc/fstab: open failed: No such file or directory [FAILED] ** (process:716): WARNING **: Couldn't create log file /var/log/ConsoleKit/history (No such file or directory) init: ck-log-system-start main process (716) terminated with status 1 Entering non-interactive startup Scan raid infomation: mdadm: No arrays found in config file or automatically Restoring /var/log to tmpfs: mount tmpfs on /var/log... extract backup logs to /var/log... 10 blocks error: bad top line in state file /var/lib/logrotate.status error: could not read state file, will not attempt to write into it error: bad top line in state file /var/lib/logrotate.status error: could not read state file, will not attempt to write into it Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Starting portreserve: [ OK ] Starting system logger: [ OK ] Starting rpcbind: [ OK ] Starting NFS statd: [ OK ] Starting RPC idmapd: FATAL: Module sunrpc not found. FATAL: Error running install command for sunrpc Error: RPC MTAB does not exist. Starting system message bus: [ OK ] Starting Avahi daemon... [ OK ] Starting cups: [ OK ] awk: cmd. line:1: fatal: cannot open file `/etc/fstab' for reading (No such file or directory) awk: cmd. line:1: fatal: cannot open file `/etc/fstab' for reading (No such file or directory) awk: cmd. line:1: fatal: cannot open file `/etc/fstab' for reading (No such file or directory) awk: cmd. line:1: fatal: cannot open file `/etc/fstab' for reading (No such file or directory) Mounting other filesystems: warning: can't open /etc/fstab: No such file or directory [ OK ] Retrigger failed udev events[ OK ] Starting NFS services: [ OK ] Starting NFS daemon: [ OK ] Starting NFS mountd: [ OK ] Starting RPC idmapd: FATAL: Module sunrpc not found. FATAL: Error running install command for sunrpc Error: RPC MTAB does not exist. Starting xinetd: [ OK ] ntpdate: Synchronizing with time server: [ OK ] Syncing hardware clock to system time [ OK ] Starting ntpd: [ OK ] Starting NAS (nas): fastcgi buttons diskmon Starting lighttpd: [ OK ] [ OK ] atd: [ OK ] swapon: /etc/fstab: open failed: No such file or directory Starting NAS LED (nasled): product was "akitio" nas-service/etc/rc3.d/S99nasled: line 83: /etc/nas/spindown: No such file or directory Starting smartd: [ OK ] Fedora release 12 (Constantine) Kernel 2.6.31.6-fast-20110114 on an armv6l (/dev/ttyS0) iSharing login:
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 20, 2023 01:33PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
How to set up U-Boot for booting in multiple drives configuration
Backup and Restore NAND mtds
UART Booting HowTo for Selected Kirkwood Devices
How to boot new Debian rootfs using stock u-boot tftp - Pogo E02
How to boot new Debian rootfs on USB using stock u-boot - NSA325
How to boot Debian rootfs on a GPT HDD with stock u-boot (kernel files stored in HDD raw sector), 2nd HowTo post
How to boot Pogo V3 from SATA (to unbrick), 2nd How to Post
Quote
Linux Kernel 5.4.xx Oxnas package and rootfs for Pogoplug Pro V3 (with PCI) and Classic V3 (no PCI). Also the Medion Life P89626, Akitio Mycloud mini, and the possibly other OXNAS boxes such as Silverstone DC01, Iconbit I-STOR IS608 (under development).
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 20, 2023 02:23PM |
Registered: 9 months ago Posts: 82 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 20, 2023 02:54PM |
Registered: 9 months ago Posts: 82 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 21, 2023 09:07AM |
Registered: 9 months ago Posts: 82 |
U-Boot 1.1.2 (Dec 24 2010 - 12:42:28) U-Boot code: 60D00000 -> 60D1A0D8 BSS: -> 60D1E790 RAM Configuration: Bank #0: 60000000 256 MB SRAM Configuration: 64KB at 0x50000000 NAND:256 MiB Using default environment In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 Extinguish LED Loading from device 0: 256MiB 3,3V 8-bit (offset 0x440000) Image Name: Linux-2.6.31.6-fast-20110114 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3056816 Bytes = 2.9 MB Load Address: 60008000 Entry Point: 60008000 ## Booting image at 60500000 ... Image Name: Linux-2.6.31.6-fast-20110114 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3056816 Bytes = 2.9 MB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................................................................................................................... done, booting the kernel. Linux version 2.6.31.6-fast-20110114 (thom@11z) (gcc version 4.5.1 (GCC) ) #1 SMP Fri Jan 14 13:58:20 CST 2011 CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Oxsemi NAS 1 memory region Ignoring unrecognised tag 0x00000000 Memory policy: ECC disabled, Data cache writealloc Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes PID hash table entries: 1024 (order: 10, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB = 256MB total Memory: 253696KB available (5260K code, 310K data, 136K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. NR_IRQS:96 OX820_RPS_init_irq: interrupts 64 to 96 Console: colour dummy device 80x30 console [ttyS0] enabled Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736) Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Calibrating local timer... 349.98MHz. CPU1: Booted secondary processor Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736) Brought up 2 CPUs SMP: Total of 2 processors activated (558.69 BogoMIPS). NET: Registered protocol family 16 Number of DMA channels = 4, version = 4 Reserving a DMA channel for DirectRAID Allocating 218 SRAM generic DMA descriptors bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Calling CRDA to update world regulatory domain NET: Registered protocol family 2 Switched to NOHz mode on CPU #0 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) Switched to NOHz mode on CPU #1 TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 Create fragment cache fuse init (API version 7.12) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 496 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A brd: module loaded loop: module loaded ox820sata: OX820 sata core. scsi0 : oxnassata scsi1 : oxnassata ata1: SATA max UDMA/133 irq 50 ata2: SATA max UDMA/133 irq 50 ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x000000000000-0x0000026c0000 : "Boot partition" 0x0000026c0000-0x000010000000 : "Data Partition" UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI error: validate_vid_hdr: bad VID header UBI error: ubi_io_read_vid_hdr: validation failed for PEB 5 UBI error: ubi_init: cannot attach mtd2 UBI error: ubi_init: UBI error: cannot initialize UBI, error -22 Probing for Synopsis GMAC, unit 0 eth0: use mtd hwaddr eth0: Tuning GMAC 0 RGMII timings eth0: PHY is Realtek RTL8211D, type 0x001cc914 eth0: GMAC ver = 53, vendor ver = 18 at 0xe1400000, IRQ 40 eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000 eth0: Ethernet addr: 00:01:d2:12:00:fa probe() eth0: Leon x2 clock tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Start USB clocks oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1 oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000 oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice IRQ 53 uses trigger mode 0; requested 3 input: gpio-keys as /devices/platform/gpio-keys/input/input0 irq 54: nobody cared (try booting with the "irqpoll" option) [<c002fab0>] (unwind_backtrace+0x0/0xe0) from [<c0076430>] (__report_bad_irq+0x78/0xa8) [<c0076430>] (__report_bad_irq+0x78/0xa8) from [<c00765e4>] (note_interrupt+0x184/0x1f0) [<c00765e4>] (note_interrupt+0x184/0x1f0) from [<c0076b44>] (handle_level_irq+0x108/0x130) [<c0076b44>] (handle_level_irq+0x108/0x130) from [<c002a054>] (asm_do_IRQ+0x54/0xa8) [<c002a054>] (asm_do_IRQ+0x54/0xa8) from [<c002abd8>] (__irq_svc+0x38/0xc0) Exception stack(0xcf813b48 to 0xcf813b90) 3b40: cf813b90 ffff8ba4 00000000 00000000 00000102 c0593ac0 3b60: cf812000 cf812000 c0023530 c056e040 c05a1d60 00000000 00000002 cf813b90 3b80: c0050b8c c00506e8 20000113 ffffffff [<c002abd8>] (__irq_svc+0x38/0xc0) from [<c00506e8>] (__do_softirq+0x50/0x140) [<c00506e8>] (__do_softirq+0x50/0x140) from [<c0050b8c>] (irq_exit+0x84/0xa0) [<c0050b8c>] (irq_exit+0x84/0xa0) from [<c002a058>] (asm_do_IRQ+0x58/0xa8) [<c002a058>] (asm_do_IRQ+0x58/0xa8) from [<c002abd8>] (__irq_svc+0x38/0xc0) Exception stack(0xcf813be8 to 0xcf813c30) 3be0: c059437c 60000013 e510001c 00000000 00000000 e510001c 3c00: c0573454 00000000 00000029 60000013 00000000 cf813d94 e500001c cf813c30 3c20: c0034b58 c03eec80 20000013 ffffffff [<c002abd8>] (__irq_svc+0x38/0xc0) from [<c03eec80>] (_spin_unlock_irqrestore+0x18/0x1c) [<c03eec80>] (_spin_unlock_irqrestore+0x18/0x1c) from [<c0034b58>] (ox820_gpio_direction_output+0x60/0xa8) [<c0034b58>] (ox820_gpio_direction_output+0x60/0xa8) from [<c0257c64>] (gpio_direction_output+0xcc/0xf0) [<c0257c64>] (gpio_direction_output+0xcc/0xf0) from [<c02e7ce8>] (i2c_start+0x18/0x44) [<c02e7ce8>] (i2c_start+0x18/0x44) from [<c02e83b4>] (bit_xfer+0x24/0x4b0) [<c02e83b4>] (bit_xfer+0x24/0x4b0) from [<c02e5ff8>] (i2c_transfer+0xb0/0xf0) [<c02e5ff8>] (i2c_transfer+0xb0/0xf0) from [<c02e62c8>] (i2c_smbus_xfer+0x290/0x54c) [<c02e62c8>] (i2c_smbus_xfer+0x290/0x54c) from [<c02e6624>] (i2c_smbus_read_i2c_block_data+0x4c/0x74) [<c02e6624>] (i2c_smbus_read_i2c_block_data+0x4c/0x74) from [<c03eb914>] (ds1307_probe+0x350/0x608) [<c03eb914>] (ds1307_probe+0x350/0x608) from [<c02e5e10>] (i2c_device_probe+0x6c/0x84) [<c02e5e10>] (i2c_device_probe+0x6c/0x84) from [<c027adac>] (driver_probe_device+0x78/0x164) [<c027adac>] (driver_probe_device+0x78/0x164) from [<c0279e1c>] (bus_for_each_drv+0x60/0x8c) [<c0279e1c>] (bus_for_each_drv+0x60/0x8c) from [<c027ac60>] (device_attach+0x70/0x88) [<c027ac60>] (device_attach+0x70/0x88) from [<c027a650>] (bus_probe_device+0x24/0x44) [<c027a650>] (bus_probe_device+0x24/0x44) from [<c0278a50>] (device_add+0x3d0/0x4b4) [<c0278a50>] (device_add+0x3d0/0x4b4) from [<c02e6fb0>] (i2c_new_device+0xbc/0x124) [<c02e6fb0>] (i2c_new_device+0xbc/0x124) from [<c02e7a10>] (i2c_register_adapter+0x124/0x1a8) [<c02e7a10>] (i2c_register_adapter+0x124/0x1a8) from [<c02e7b44>] (i2c_add_numbered_adapter+0xb0/0xc8) [<c02e7b44>] (i2c_add_numbered_adapter+0xb0/0xc8) from [<c03ebd50>] (i2c_gpio_probe+0x184/0x244) [<c03ebd50>] (i2c_gpio_probe+0x184/0x244) from [<c027bb20>] (platform_drv_probe+0x18/0x1c) [<c027bb20>] (platform_drv_probe+0x18/0x1c) from [<c027adac>] (driver_probe_device+0x78/0x164) [<c027adac>] (driver_probe_device+0x78/0x164) from [<c027af24>] (__driver_attach+0x8c/0x90) [<c027af24>] (__driver_attach+0x8c/0x90) from [<c027a0e4>] (bus_for_each_dev+0x54/0x80) [<c027a0e4>] (bus_for_each_dev+0x54/0x80) from [<c027a78c>] (bus_add_driver+0x98/0x230) [<c027a78c>] (bus_add_driver+0x98/0x230) from [<c027b14c>] (driver_register+0x78/0x13c) [<c027b14c>] (driver_register+0x78/0x13c) from [<c001ca50>] (i2c_gpio_init+0xc/0x30) [<c001ca50>] (i2c_gpio_init+0xc/0x30) from [<c002a5b8>] (do_one_initcall+0x30/0x1a0) [<c002a5b8>] (do_one_initcall+0x30/0x1a0) from [<c0008bf8>] (kernel_init+0x16c/0x1f8) [<c0008bf8>] (kernel_init+0x16c/0x1f8) from [<c002bad8>] (kernel_thread_exit+0x0/0x8) handlers: [<c02e3210>] (gpio_keys_isr+0x0/0x8c) Disabling IRQ #54 rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0 i2c-gpio i2c-gpio.0: using pins 41 (SDA) and 42 (SCL) md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 Registered led device: hddaerr Registered led device: hddberr Registered led device: system Registered led device: firmware Registered led device: usbcopy TCP cubic registered NET: Registered protocol family 10 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc-ds1307 0-0068: setting system clock to 2023-11-21 14:51:03 UTC (1700578263) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:rootfs", error -19 VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 262144 mtdblock0 (driver?) 1f01 39680 mtdblock1 (driver?) 1f02 222464 mtdblock2 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [<c002fab0>] (unwind_backtrace+0x0/0xe0) from [<c03ec2dc>] (panic+0x44/0x100) [<c03ec2dc>] (panic+0x44/0x100) from [<c0008f64>] (mount_block_root+0x1d8/0x29c) [<c0008f64>] (mount_block_root+0x1d8/0x29c) from [<c000921c>] (prepare_namespace+0x90/0x1c0) [<c000921c>] (prepare_namespace+0x90/0x1c0) from [<c0008c3c>] (kernel_init+0x1b0/0x1f8) [<c0008c3c>] (kernel_init+0x1b0/0x1f8) from [<c002bad8>] (kernel_thread_exit+0x0/0x8) CPU1: stopping [<c002fab0>] (unwind_backtrace+0x0/0xe0) from [<c002a35c>] (do_IPI+0xe8/0x150) [<c002a35c>] (do_IPI+0xe8/0x150) from [<c002abd8>] (__irq_svc+0x38/0xc0) Exception stack(0xcf83df98 to 0xcf83dfe0) df80: 2afbfe1e 00000000 dfa0: cf83dfe0 00000000 cf83c000 c0593d24 c057280c c0594234 00000000 410fb025 dfc0: 60021d84 00000000 ffff8be0 cf83dfe0 c002bb30 c002bb34 60000013 ffffffff [<c002abd8>] (__irq_svc+0x38/0xc0) from [<c002bb34>] (default_idle+0x24/0x28) [<c002bb34>] (default_idle+0x24/0x28) from [<c002bd14>] (cpu_idle+0x64/0x98) [<c002bd14>] (cpu_idle+0x64/0x98) from [<60008084>] (0x60008084)
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 21, 2023 09:38AM |
Registered: 9 months ago Posts: 82 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 21, 2023 01:56PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 22, 2023 01:08PM |
Registered: 9 months ago Posts: 82 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 22, 2023 01:37PM |
Registered: 9 months ago Posts: 82 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 22, 2023 03:56PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
How to boot Pogo V3 from SATA (to unbrick), 2nd How to Post
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 22, 2023 06:51PM |
Registered: 9 months ago Posts: 82 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 23, 2023 10:27AM |
Registered: 9 months ago Posts: 82 |
Latest released kernel: linux-5.4.224-oxnas-tld-1.bodhi.tar.bz2 (16 Nov 2022) Latest released rootfs: Debian-4.14.180-oxnas-tld-1-rootfs-bodhi.tar.bz2 (17 May 2020) Note: If this is your first time installation, then you only need rootfs Debian-4.14.180-oxnas-tld-1-rootfs-bodhi.tar.bz2 (this has kernel linux-4.14.180-oxnas-tld-1 already installed). Scroll down to 17 May 2020 section. With this kernel we can run the Pogo V3 boxes with the latest U-Boot (e.g. 2013.10 and later). To run with stock U-Boot, use kernel 3.18.5 or earlier.
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 24, 2023 02:51PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
This guide troubled me so much that I didn’t know how to follow the instructions in the article.
Quote
Linux Kernel 5.4.xx Oxnas package and rootfs for Pogoplug Pro V3 (with PCI) and Classic V3 (no PCI). Also the Medion Life P89626, Akitio Mycloud mini, and the possibly other OXNAS boxes such as Silverstone DC01, Iconbit I-STOR IS608 (under development)
Quote
How to boot Pogo V3 from SATA (to unbrick), 2nd How to Post
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 25, 2023 04:45PM |
Registered: 9 months ago Posts: 82 |
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34) Boot device: SATA Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set Bus 0: OK Device 0: Failed to mount ext2 filesystem... ### ERROR ### Please RESET the board ###
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 25, 2023 05:14PM |
Registered: 9 months ago Posts: 82 |
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34) Boot device: SATA Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set Bus 0: OK Device 0: ** File not found /boot/bootargs.bin ** ** File not found /boot/u-boot.img ** ### ERROR ### Please RESET the board ###
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: APPLE HDD HTS547550A9E384 Firm: JE3AD70F Ser#: J2600055GJDE2E
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
2212156 bytes read in 773 ms (2.7 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-2.6.31.14_OX820_1.2_shv
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2212092 Bytes = 2.1 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux....................................................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Oxsemi NAS
[ 0.000000] 1 memory region
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 125368KB available (3816K code, 304K data, 132K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:96
[ 0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[ 0.010000] Console: colour dummy device 80x30
[ 0.010000] console [ttyS0] enabled
[ 0.020000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.230000] Security Framework initialized
[ 0.230000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] Calibrating local timer... 424.49MHz.
[ 0.310000] CPU1: Booted secondary processor
[ 0.410000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.620000] Brought up 2 CPUs
[ 0.630000] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.640000] NET: Registered protocol family 16
[ 0.640000] Number of DMA channels = 4, version = 4
[ 0.650000] Reserving a DMA channel for DirectRAID
[ 0.650000] Allocating 389 SRAM generic DMA descriptors
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 25, 2023 05:59PM |
Admin Registered: 13 years ago Posts: 18,821 |
[ 0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 25, 2023 06:20PM |
Registered: 9 months ago Posts: 82 |
After this preparation of the boot area of the disk you have to write the linux file system to the SATA drive: I have used the current latest version for this: Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 Unpack the archive to a temporary directory on your system (all this still logged in as root (sudo -i)) to a working directory: I have created a ´sataboot´ directory in my home directory with: mkdir /home/sataboot cd /home/sataboot tar -xjf /PathToArchive/Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 Then copy all files extracted form the archive to the mounted drive labeled ´rootfs´ directory, but DO NOT COPY the newly created ./boot directory! Because then the sata boot images will be overwritten..... You can manually copy all other directories one by one like this: still from within /home/sataboot or cd to it: cp -r ./xxx /media/john/rootfs Where xxx is substituted with bin, usr, home, dev etc. but skip! the ./boot directory. You can also move the ./boot directory elswhere, e.g. mv ./boot /home/tempboot/ and after that and from within the /home/sataboot directory copy al directories and files to the ´rootfs´ labeled sata drive with: cp -r . /media/john/rootfs/
Linux Kernel 5.4.xx Oxnas package and rootfs for Pogoplug Pro V3 (with PCI) and Classic V3 (no PCI). Also the Medion Life P89626, Akitio Mycloud mini, and the possibly other OXNAS boxes such as Silverstone DC01, Iconbit I-STOR IS608 (under development). If you install this kernel on other OX820 boxes, please post your finding so it can be added to the supported list. Latest released kernel: linux-5.4.224-oxnas-tld-1.bodhi.tar.bz2 (16 Nov 2022) Latest released rootfs: Debian-4.14.180-oxnas-tld-1-rootfs-bodhi.tar.bz2 (17 May 2020) Note: If this is your first time installation, then you only need rootfs Debian-4.14.180-oxnas-tld-1-rootfs-bodhi.tar.bz2 (this has kernel linux-4.14.180-oxnas-tld-1 already installed). Scroll down to 17 May 2020 section. With this kernel we can run the Pogo V3 boxes with the latest U-Boot (e.g. 2013.10 and later). To run with stock U-Boot, use kernel 3.18.5 or earlier.
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 26, 2023 02:12AM |
Registered: 9 months ago Posts: 82 |
cp -a uImage uImage.orig cp -a zImage-4.14.180-oxnas-tld-1 zImage.fdt cat dts/ox820-akitio.dtb >> zImage.fdt mkimage -A arm -O linux -C none -T kernel -a 0x60008000 -e 0x60008000 -n 'Linux-4.14.180-oxnas-tld-1' -d zImage.fdt uImage sync
drwxr-xr-x 3 admin administrators 4096 2023-11-26 15:27 ./ drwxrwxrwx 19 admin administrators 4096 2023-11-26 15:23 ../ -rw-r--r-- 1 admin administrators 126846 2023-11-26 15:23 config-4.14.180-oxnas-tld-1 drwxr-xr-x 2 admin administrators 4096 2023-11-26 15:23 dts/ -rw-r--r-- 1 admin administrators 6464843 2023-11-26 15:23 initrd.img-4.14.180-oxnas-tld-1 -rw-r--r-- 1 admin administrators 10872364 2023-11-26 15:23 linux-headers-4.14.180-oxnas-tld-1_1.0_armel.deb -rw-r--r-- 1 admin administrators 1797644 2023-11-26 15:23 System.map-4.14.180-oxnas-tld-1 -rwxr-xr-x 1 admin administrators 16384 2023-11-26 15:27 u-boot.env* -rw-r--r-- 1 admin administrators 525880 2023-11-26 15:27 u-boot.img -rwxr-xr-x 1 admin administrators 32120 2023-11-26 15:27 u-boot-spl.bin* -rw-r--r-- 1 admin administrators 4610393 2023-11-26 15:23 uImage -rw-r--r-- 1 admin administrators 4600448 2023-11-26 15:23 uImage.orig -rw-r--r-- 1 admin administrators 6464907 2023-11-26 15:23 uInitrd -rwxr-xr-x 1 admin administrators 4600384 2023-11-26 15:23 vmlinuz-4.14.180-oxnas-tld-1* -rwxr-xr-x 1 admin administrators 4600384 2023-11-26 15:23 zImage-4.14.180-oxnas-tld-1* -rwxr-xr-x 1 admin administrators 4610329 2023-11-26 15:23 zImage.fdt*
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34) Boot device: SATA Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set Bus 0: OK Device 0: ** File not found /boot/bootargs.bin ** U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS DRAM: 256 MiB IDE: Bus 0: OK Device 0: Model: APPLE HDD HTS547550A9E384 Firm: JE3AD70F Ser#: J2600055GJDE2E Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) NAND: 256 MiB In: serial Out: serial Err: serial Net: Led: GREEN mii0 Main Loop Hit any key to stop autoboot: 0 OX820 # OX820 # OX820 # setenv dt_ide_load_dtb ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb OX820 # printenv dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr autoload=no baudrate=115200 bootargs=console=ttyS0,115200n8 bootcmd=run dt_bootcmd_ide bootdelay=3 console=console=ttyS0,115200n8 dt_bootcmd_ide=ide start; run dt_ide_bootcmd; ide stop; reset dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot dt_ide_load_dtb=ext2load ide 0:1 0x62c00000 /boot/dts/ox820-akitio.dtb dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; bootm $uimage_addr dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot dtb_addr=0x62c00000 ethact=mii0 ethaddr=00:30:E0:00:00:01 ide_set_bootargs=setenv bootargs root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes if_netconsole=ping $serverip ipaddr=192.168.0.100 mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) preboot_nc=run if_netconsole start_netconsole sata_bootcmd=run usb_set_bootargs; run sata_boot start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version stderr=serial stdin=serial stdout=serial uimage_addr=0x60500000 uinitrd_addr=0x60e00000 usb_device=0:1 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10 Environment size: 1960/16380 bytes OX820 # setenv dt_load_dtb ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb OX820 # printenv dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr autoload=no baudrate=115200 bootargs=console=ttyS0,115200n8 bootcmd=run dt_bootcmd_ide bootdelay=3 console=console=ttyS0,115200n8 dt_bootcmd_ide=ide start; run dt_ide_bootcmd; ide stop; reset dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot dt_ide_load_dtb=ext2load ide 0:1 0x62c00000 /boot/dts/ox820-akitio.dtb dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage dt_load_dtb=ext2load usb 0:1 0x62c00000 /boot/dts/ox820-akitio.dtb dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; bootm $uimage_addr dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot dtb_addr=0x62c00000 ethact=mii0 ethaddr=00:30:E0:00:00:01 ide_set_bootargs=setenv bootargs root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes if_netconsole=ping $serverip ipaddr=192.168.0.100 mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) preboot_nc=run if_netconsole start_netconsole sata_bootcmd=run usb_set_bootargs; run sata_boot start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version stderr=serial stdin=serial stdout=serial uimage_addr=0x60500000 uinitrd_addr=0x60e00000 usb_device=0:1 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10 Environment size: 1955/16380 bytes OX820 # saveenv Saving Environment to EXT4... File System is consistent file found deleting update journal finished File System is consistent update journal finished done
OX820 # run dt_ide_boot
4610393 bytes read in 1575 ms (2.8 MiB/s)
6464907 bytes read in 2225 ms (2.8 MiB/s)
9945 bytes read in 42 ms (230.5 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.14.180-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4610329 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-4.14.180-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6464843 Bytes = 6.2 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f7fe000, end 6fe2854b ... OK
Loading Device Tree to 6f7f8000, end 6f7fd6d8 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Akitio MyCloud
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: earlyprintk console=ttyS0,115200
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 119024K/131072K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 12048K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0800000 (8160 kB)
[ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB)
[ 0.000000] .data : 0xc0b00000 - 0xc0b31f68 ( 200 kB)
[ 0.000000] .bss : 0xc0b383b8 - 0xc0b757c0 ( 246 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] FPGA IRQ chip 0 "interrupt-controller" @ c8804000, 32 irqs, parent IRQ: 16
[ 0.000015] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008163] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.018887] timer_oxnas_rps: Registered clocksource rate 390625Hz
[ 0.025044] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[ 0.033571] GIC: PPI13 is secure or misconfigured
[ 0.038376] GIC: PPI13 is secure or misconfigured
[ 0.043307] Console: colour dummy device 80x30
[ 0.047846] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.094776] pid_max: default: 32768 minimum: 301
[ 0.099735] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.106416] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.114519] CPU: Testing write buffer coherency: ok
[ 0.158533] Setting up static identity map for 0x60100000 - 0x60100038
[ 0.165345] Hierarchical SRCU implementation.
[ 0.208435] smp: Bringing up secondary CPUs ...
[ 0.258549] GIC: PPI13 is secure or misconfigured
[ 0.318717] smp: Brought up 1 node, 2 CPUs
[ 0.327649] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.334819] devtmpfs: initialized
[ 0.344291] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.354242] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.360750] prandom: seed boundary self test passed
[ 0.369912] prandom: 100 self tests passed
[ 0.374074] pinctrl core: initialized pinctrl subsystem
[ 0.380075] NET: Registered protocol family 16
[ 0.386117] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.395427] cpuidle: using governor ladder
[ 0.399715] cpuidle: using governor menu
[ 0.422940] vgaarb: loaded
[ 0.426196] SCSI subsystem initialized
[ 0.430812] usbcore: registered new interface driver usbfs
[ 0.436456] usbcore: registered new interface driver hub
[ 0.442060] usbcore: registered new device driver usb
[ 0.447344] pps_core: LinuxPPS API ver. 1 registered
[ 0.452433] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.461688] PTP clock support registered
[ 0.466703] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[ 0.491919] NET: Registered protocol family 2
[ 0.497328] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.504366] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.510860] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.517450] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.523374] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.530012] NET: Registered protocol family 1
[ 0.535257] RPC: Registered named UNIX socket transport module.
[ 0.541291] RPC: Registered udp transport module.
[ 0.546060] RPC: Registered tcp transport module.
[ 0.550865] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.558886] Initialise system trusted keyrings
[ 0.563440] Key type blacklist registered
[ 0.567920] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.581890] zbud: loaded
[ 0.589248] NFS: Registering the id_resolver key type
[ 0.594383] Key type id_resolver registered
[ 0.598707] Key type id_legacy registered
[ 0.602805] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.609610] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.616952] fuse init (API version 7.26)
[ 0.621847] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 0.628664] orangefs_init: module version upstream loaded
[ 2.581145] Key type asymmetric registered
[ 2.585318] Asymmetric key parser 'x509' registered
[ 2.590400] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 2.597957] io scheduler noop registered
[ 2.601950] io scheduler deadline registered
[ 2.606338] io scheduler cfq registered (default)
[ 2.613396] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.621386] console [ttyS0] disabled
[ 2.625152] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[ 2.634124] console [ttyS0] enabled
[ 2.634124] console [ttyS0] enabled
[ 2.641190] bootconsole [earlycon0] disabled
[ 2.641190] bootconsole [earlycon0] disabled
[ 2.660846] loop: module loaded
[ 2.666245] scsi host0: sata_oxnas
[ 2.670374] scsi host1: sata_oxnas
[ 2.674048] ata1: SATA max UDMA/133 irq 57
[ 2.678182] ata2: SATA max UDMA/133 irq 57
[ 2.682373] sata_oxnas: resetting SATA core
[ 2.747038] nand: Could not find valid ONFI parameter page; aborting
[ 2.753377] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[ 2.759749] nand: Hynix NAND 256MiB 3,3V 8-bit
[ 2.764177] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.771758] Scanning device for bad blocks
[ 2.942699] 2 ofpart partitions found on MTD device 41000000.nand-controller
[ 2.949795] Creating 2 MTD partitions on "41000000.nand-controller":
[ 2.956175] 0x000000000000-0x0000026c0000 : "boot"
[ 2.963038] 0x0000026c0000-0x000010000000 : "ubi"
[ 2.972049] libphy: Fixed MDIO Bus: probed
[ 2.976529] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[ 2.982410] oxnas-dwmac 40400000.ethernet: no reset control found
[ 3.056806] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 3.061841] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[ 3.067530] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[ 3.074805] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[ 3.081594] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[ 3.088209] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[ 3.095488] oxnas-dwmac 40400000.ethernet: COE Type 2
[ 3.100544] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[ 3.107420] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[ 3.113669] oxnas-dwmac 40400000.ethernet (unnamed net_device) (uninitialized): device MAC address e2:56:9b:72:78:6c
[ 3.124175] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.141299] libphy: stmmac: probed
[ 3.144704] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 3.154191] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[ 3.164587] PPP generic driver version 2.4.2
[ 3.169228] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.175731] ehci-pci: EHCI PCI platform driver
[ 3.196792] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3.203850] ata1.00: ATA-8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133
[ 3.211023] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 3.218677] ata1.00: configured for UDMA/133
[ 3.223503] scsi 0:0:0:0: Direct-Access ATA APPLE HDD HTS547 D70F PQ: 0 ANSI: 5
[ 3.233169] sata_oxnas: resetting SATA core
[ 3.233374] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 3.244879] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 3.250165] sata_oxnas: resetting SATA core
[ 3.396776] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 3.402283] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 3.410199] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[ 3.436753] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 3.443072] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.449945] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.457175] usb usb1: Product: EHCI Host Controller
[ 3.462031] usb usb1: Manufacturer: Linux 4.14.180-oxnas-tld-1 ehci_hcd
[ 3.468692] usb usb1: SerialNumber: 40200100.ehci
[ 3.474196] hub 1-0:1.0: USB hub found
[ 3.478105] hub 1-0:1.0: 2 ports detected
[ 3.483092] usbcore: registered new interface driver cdc_wdm
[ 3.489018] usbcore: registered new interface driver usb-storage
[ 3.495157] usbcore: registered new interface driver usbserial
[ 3.501089] usbcore: registered new interface driver usbserial_generic
[ 3.507776] usbserial: USB Serial support registered for generic
[ 3.514104] mousedev: PS/2 mouse device common for all mice
[ 3.519836] i2c /dev entries driver
[ 3.524615] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.530350] usbcore: registered new interface driver usbhid
[ 3.535900] usbhid: USB HID core driver
[ 3.540997] NET: Registered protocol family 10
[ 3.546995] Segment Routing with IPv6
[ 3.550727] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.558423] NET: Registered protocol family 17
[ 3.562961] Key type dns_resolver registered
[ 3.568601] registered taskstats version 1
[ 3.572684] Loading compiled-in X.509 certificates
[ 3.577602] zswap: loaded using pool lzo/zbud
[ 3.590338] Key type big_key registered
[ 3.596904] Key type encrypted registered
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34) Boot device: SATA Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set Bus 0: OK Device 0: ** File not found /boot/bootargs.bin ** U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS DRAM: 256 MiB IDE: Bus 0: OK Device 0: Model: APPLE HDD HTS547550A9E384 Firm: JE3AD70F Ser#: J2600055GJDE2E Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) NAND: 256 MiB In: serial Out: serial Err: serial Net: Led: GREEN mii0 Main Loop Hit any key to stop autoboot: 0 ide - IDE sub-system Usage: ide reset - reset IDE controller ide info - show available IDE devices ide device [dev] - show or set current device ide part [dev] - print partition table of one or all IDE devices ide read addr blk# cnt ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#' to/from memory address `addr' 4610393 bytes read in 1673 ms (2.6 MiB/s) ## Booting kernel from Legacy Image at 60500000 ... Image Name: Linux-4.14.180-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4610329 Bytes = 4.4 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK Loading Kernel Image ... OK Led: GREEN Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020 [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Akitio MyCloud [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 248976K/262144K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 13168K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0800000 (8160 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b31f68 ( 200 kB) [ 0.000000] .bss : 0xc0b383b8 - 0xc0b757c0 ( 246 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] FPGA IRQ chip 0 "interrupt-controller" @ d0804000, 32 irqs, parent IRQ: 16 [ 0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.000048] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.000064] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.000092] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.000240] GIC: PPI13 is secure or misconfigured [ 0.000294] GIC: PPI13 is secure or misconfigured [ 0.000471] Console: colour dummy device 80x30 [ 0.000514] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.050391] pid_max: default: 32768 minimum: 301 [ 0.050654] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.050680] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.051553] CPU: Testing write buffer coherency: ok [ 0.090444] Setting up static identity map for 0x60100000 - 0x60100038 [ 0.110348] Hierarchical SRCU implementation. [ 0.150348] smp: Bringing up secondary CPUs ... [ 0.220459] GIC: PPI13 is secure or misconfigured [ 0.280634] smp: Brought up 1 node, 2 CPUs [ 0.280665] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.281402] devtmpfs: initialized [ 0.287447] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.287480] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.287815] prandom: seed boundary self test passed [ 0.292103] prandom: 100 self tests passed [ 0.292124] pinctrl core: initialized pinctrl subsystem [ 0.292843] NET: Registered protocol family 16 [ 0.294484] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.296957] cpuidle: using governor ladder [ 0.297029] cpuidle: using governor menu [ 0.315617] vgaarb: loaded [ 0.316119] SCSI subsystem initialized [ 0.316833] usbcore: registered new interface driver usbfs [ 0.316938] usbcore: registered new interface driver hub [ 0.317086] usbcore: registered new device driver usb [ 0.317268] pps_core: LinuxPPS API ver. 1 registered [ 0.317286] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.317317] PTP clock support registered [ 0.318400] clocksource: Switched to clocksource oxnas_rps_clocksource_timer [ 0.333995] NET: Registered protocol family 2 [ 0.334881] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.334932] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.334986] TCP: Hash tables configured (established 2048 bind 2048) [ 0.335155] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.335201] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.335470] NET: Registered protocol family 1 [ 0.336271] RPC: Registered named UNIX socket transport module. [ 0.336291] RPC: Registered udp transport module. [ 0.336307] RPC: Registered tcp transport module. [ 0.336320] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.338531] Initialise system trusted keyrings [ 0.338600] Key type blacklist registered [ 0.338859] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.345456] zbud: loaded [ 0.350026] NFS: Registering the id_resolver key type [ 0.350077] Key type id_resolver registered [ 0.350092] Key type id_legacy registered [ 0.350123] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.350138] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.350991] fuse init (API version 7.26) [ 0.351915] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.352184] orangefs_init: module version upstream loaded [ 2.233574] alg: hash: Test 4 failed fo4 sha224-generic [ 2.233602] 00000000: 6b 62 25 2a 52 f5 e7 69 e2 92 0a 0e a6 62 f8 11 [ 2.233620] 00000010: e4 92 e5 81 53 2b 39 59 a3 7c 87 ▒e [ 2.234324] alg: cipher: Test 1 failed on encryption fo# arc4-generic [ 2.234352] 00000000: 75 b7 87 80 99 60 c5 96 [ 2.235962] alg: comp: Compression test▒1 failed for deflate-generic: output len = 75 [ 2.241515] alg: acomp: decompression failed on test 1 for zlib-deflate-scomp: ret=22 [ 2.243645] alg: acomp: Compression tesh 1 failed for lzo-scomp [ 2.243673] 00000000: 00 0d 4a 6f 69 6e 20 75 73 20 6e 6f 77 20 61 6e [ 2.243691] 00000010: 64 20 73 68 61 72 65 20 74 68 65 20 73 6f 66 74 [ 2.243704] 00000020: 77 70 01 32 88 00 0c 65 20 74 68 65 20 73 6f 66 [ 2.243719] 00000030: 74 77 61 72 65 20 11 00 00 00 00 00 00 00 00 00 [ 2.243732] 00000040: 00 00 00 00 00 0 [ 2.293498] alg: hash: Test 8 failed fo▒ hmac(sha256-generic) [ 2.293527] 00000000: 6d 5d ff d5 43 ae 55 8c 9c 55 7e 21 45 b2 1d 1a [ 2.293542] 00000010: 8b 0a 84 ec 20 2d 89 e1 a2 47 68 13 12 36 79 2b [ 2.293701] DRBG: could not allocate digest TFM handle:chmac(sha256) [ 2.293721] alg: drbg: Failed to reset rng [ 2.293736] alg: drbg: Test 0 failed fo drbg_pr_hmac_sha256 [ 2.300771] alg: hash: Chunking test 1 failed for ghash-generc [ 2.300800] 00000000: 94 0b 9a 59 a3 e4 29 da cb 75 c0 33 a0 45 14 44 [ 2.300892] Key type asymmetric registered [ 2.300917] Asymmetric key parser 'x509' registered [ 2.301022] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 2.301043] io scheduler noop registered [ 2.301056] io scheduler deadline registered [ 2.301114] io scheduler cfq registered (default) [ 2.303362] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 2.304793] console [ttyS0] disabled [ 2.304934] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A [ 3.000476] console [ttyS0] enabled [ 3.014743] loop: module loaded [ 3.020321] scsi host0: sata_oxnas [ 3.024378] scsi host1: sata_oxnas [ 3.028057] ata1: SATA max UDMA/133 irq 57 [ 3.032199] ata2: SATA max UDMA/133 irq 57 [ 1.036392] sata_oxnas: resetting SATA core [ 3.098736] nand: Could not find valid ONFI parameter page; aborting [ 3.105075] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 3.111441] nand: Hynix NAND 256MiB 3,3V 8-bit [ 3.115865] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 3.123445] Scanning device for bad blocks [ 3.293120] 2 ofpart partitions found on MTD device 41000000.nand-controller [ 3.300167] Creating 2 MTD partitions on "41000000.nand-controller": [ 3.306501] 0x000000000000-0x0000026c0000 : "boot" [ 3.313162] 0x0000026c0000-0x000010000000 : "ubi" [ 3.322073] libphy: Fixed MDIO Bus: probed [ 3.326568] oxnas-dwmac 40400000.ethernet: PTP uses main clock [ 3.332441] oxnas-dwmac 40400000.ethernet: no reset control found [ 3.408501] stmmac - user ID: 0x12, Synopsys ID: 0x35 [ 3.413542] oxnas-dwmac 40400000.ethernet: Ring mode enabled [ 3.419233] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported [ 3.426508] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors [ 3.433297] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors [ 3.439912] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported [ 3.447188] oxnas-dwmac 40400000.ethernet: COE Type 2 [ 3.452247] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported [ 3.459118] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported [ 3.465369] oxnas-dwmac 40400000.ethernet (unnamed net_device) (uninitialized): device MAC address 2e:8d:3e:51:1f:b2 [ 3.475875] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 3.492992] libphy: stmmac: probed [ 3.496396] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 3.505884] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL) [ 3.516270] PPP generic driver version 2.4.2 [ 3.520885] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.527388] ehci-pci: EHCI PCI platform driver [ 6.548480] ata▒: SATA link up 1.5 Gbps (SStatun 113 SControl 30) [ 3.0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000619105] ata.00: AT -8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133 [ 3.0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000655567] ata.00: 976773168 sectors, multi 0h LBA48 NCQ (depth▒0/32) [ 3.738467] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 3.743974] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 3.751846] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100 [ 3.778467] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 3.784773] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.791590] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.798817] usb usb1: Product: EHCI Host Controller [ 3.803673] usb usb1: Manufacturer: Linux 4.14.180-oxnas-tld-1 ehci_hcd [ 3.810291] usb usb1: SerialNumber: 40200100.ehci [ 3.815820] hub 1-0:1.0: USB hub found [ 3.819724] hub 1-0:1.0: 2 ports detected [ 3.824691] usbcore: registered new interface driver cdc_wdm [ 3.830528] usbcore: registered new interface driver usb-storage [ 3.836641] usbcore: registered new interface driver usbserial [ 3.842603] usbcore: registered new interface driver usbserial_generic [ 3.849203] usbserial: USB Serial support registered for generic [ 3.855513] mousedev: PS/2 mouse device common for all mice [ 3.861271] i2c /dev entries driver [ 3.865966] hidraw: raw HID events driver (C) Jiri Kosina [ 3.871585] usbcore: registered new interface driver usbhid [ 3.877132] usbhid: USB HID core driver [ 3.882252] NET: Registered protocol family 10 [ 3.888163] Segment Routing with IPv6 [ 3.891973] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.899701] NET: Registered protocol family 17 [ 3.904268] Key type dns_resolver registered [ 3.909788] registered taskstats version 1 [ 3.913871] Loading compiled-in X.509 certificates [ 3.918799] zswap: loaded using pool lzo/zbud [ 3.924490] UBIFS error (pid 1): cannot initialize compressor zlib, error -2 [ 3.926266] big_key: Can't alloc crypto: -2 [ 3.938961] alg: No test for cbc(aDs) (cbc(aes-gener▒c)) [ 3.944358] encrypted_key: failed to alloc_cipher (-2)
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 26, 2023 02:38PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 26, 2023 03:24PM |
Registered: 9 months ago Posts: 82 |
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: APPLE HDD HTS547550A9E384 Firm: JE3AD70F Ser#: J2600055GJDE2E
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 0x62c00000 /boot/dts/ox820-pogoplug-classic.dtb'
OX820 # run dt_ide_boot
4600448 bytes read in 1715 ms (2.6 MiB/s)
6464907 bytes read in 2236 ms (2.8 MiB/s)
8892 bytes read in 43 ms (201.2 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.14.180-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4600384 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-4.14.180-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6464843 Bytes = 6.2 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f7fe000, end 6fe2854b ... OK
Loading Device Tree to 6f7f8000, end 6f7fd2bb ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Pogoplug V3 Classic
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200n8
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 242664K/262144K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 19480K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0800000 (8160 kB)
[ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB)
[ 0.000000] .data : 0xc0b00000 - 0xc0b31f68 ( 200 kB)
[ 0.000000] .bss : 0xc0b383b8 - 0xc0b757c0 ( 246 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] FPGA IRQ chip 0 "interrupt-controller" @ d0804000, 32 irqs, parent IRQ: 16
[ 0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.000046] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000061] timer_oxnas_rps: Registered clocksource rate 390625Hz
[ 0.000087] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[ 0.000235] GIC: PPI13 is secure or misconfigured
[ 0.000289] GIC: PPI13 is secure or misconfigured
[ 0.000458] Console: colour dummy device 80x30
[ 0.000504] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.050383] pid_max: default: 32768 minimum: 301
[ 0.050657] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.050682] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.051676] CPU: Testing write buffer coherency: ok
[ 0.090444] Setting up static identity map for 0x60100000 - 0x60100038
[ 0.110343] Hierarchical SRCU implementation.
[ 0.150346] smp: Bringing up secondary CPUs ...
[ 0.220451] GIC: PPI13 is secure or misconfigured
[ 0.280629] smp: Brought up 1 node, 2 CPUs
[ 0.280663] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.281287] devtmpfs: initialized
[ 0.286650] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.286684] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.287014] prandom: seed boundary self test passed
[ 0.291299] prandom: 100 self tests passed
[ 0.291320] pinctrl core: initialized pinctrl subsystem
[ 0.292008] NET: Registered protocol family 16
[ 0.293555] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.295838] cpuidle: using governor ladder
[ 0.295912] cpuidle: using governor menu
[ 0.313676] vgaarb: loaded
[ 0.314178] SCSI subsystem initialized
[ 0.314874] usbcore: registered new interface driver usbfs
[ 0.314979] usbcore: registered new interface driver hub
[ 0.315136] usbcore: registered new device driver usb
[ 0.315317] pps_core: LinuxPPS API ver. 1 registered
[ 0.315335] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.315371] PTP clock support registered
[ 0.316382] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[ 0.332244] NET: Registered protocol family 2
[ 0.333143] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.333196] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.333253] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.333411] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.333460] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.333724] NET: Registered protocol family 1
[ 0.334520] RPC: Registered named UNIX socket transport module.
[ 0.334545] RPC: Registered udp transport module.
[ 0.334561] RPC: Registered tcp transport module.
[ 0.334574] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.334968] Unpacking initramfs...
[ 1.057653] Freeing initrd memory: 6316K
[ 1.058757] Initialise system trusted keyrings
[ 1.058821] Key type blacklist registered
[ 1.059102] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 1.066227] zbud: loaded
[ 1.071078] NFS: Registering the id_resolver key type
[ 1.071124] Key type id_resolver registered
[ 1.071137] Key type id_legacy registered
[ 1.071165] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.071180] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.072007] fuse init (API version 7.26)
[ 1.072898] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 1.073152] orangefs_init: module version upstream loaded
[ 3.055575] Key type asymmetric registered
[ 3.055600] Asymmetric key parser 'x509' registered
[ 3.055700] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 3.055718] io scheduler noop registered
[ 3.055731] io scheduler deadline registered
[ 3.055792] io scheduler cfq registered (default)
[ 3.057628] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 3.059048] console [ttyS0] disabled
[ 3.059182] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[ 3.627819] console [ttyS0] enabled
[ 3.641866] loop: module loaded
[ 3.646860] scsi host0: sata_oxnas
[ 3.650575] ata1: SATA max UDMA/133 irq 57
[ 3.654758] sata_oxnas: resetting SATA core
[ 3.716728] nand: Could not find valid ONFI parameter page; aborting
[ 3.723064] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[ 3.729436] nand: Hynix NAND 256MiB 3,3V 8-bit
[ 3.733864] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 3.741447] Scanning device for bad blocks
[ 3.911357] 2 ofpart partitions found on MTD device 41000000.nand-controller
[ 3.918405] Creating 2 MTD partitions on "41000000.nand-controller":
[ 3.924736] 0x000000000000-0x000000e00000 : "boot"
[ 3.931115] 0x000000e00000-0x000008000000 : "data"
[ 3.938984] libphy: Fixed MDIO Bus: probed
[ 3.943485] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[ 3.949352] oxnas-dwmac 40400000.ethernet: no reset control found
[ 4.016488] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 4.021527] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[ 4.027217] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[ 4.034496] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[ 4.041285] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[ 4.047900] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[ 4.055175] oxnas-dwmac 40400000.ethernet: COE Type 2
[ 4.060231] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[ 4.067105] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[ 4.073346] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 4.125012] libphy: stmmac: probed
[ 4.128488] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 4.137991] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[ 4.148418] PPP generic driver version 2.4.2
[ 4.152929] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.159531] ehci-pci: EHCI PCI platform driver
[ 4.166461] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 4.173504] ata1.00: ATA-8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133
[ 4.180664] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 4.188295] ata1.00: configured for UDMA/133
[ 4.203194] scsi 0:0:0:0: Direct-Access ATA APPLE HDD HTS547 D70F PQ: 0 ANSI: 5
[ 4.212994] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 4.220505] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 4.225822] sd 0:0:0:0: [sda] Write Protect is off
[ 4.230912] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.366461] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 4.371970] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 4.379868] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[ 4.406453] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 4.412771] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.419589] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.426816] usb usb1: Product: EHCI Host Controller
[ 4.431667] usb usb1: Manufacturer: Linux 4.14.180-oxnas-tld-1 ehci_hcd
[ 4.438282] usb usb1: SerialNumber: 40200100.ehci
[ 4.443824] hub 1-0:1.0: USB hub found
[ 4.447685] hub 1-0:1.0: 2 ports detected
[ 4.452636] usbcore: registered new interface driver cdc_wdm
[ 4.458483] usbcore: registered new interface driver usb-storage
[ 4.464596] usbcore: registered new interface driver usbserial
[ 4.470525] usbcore: registered new interface driver usbserial_generic
[ 4.477145] usbserial: USB Serial support registered for generic
[ 4.483445] mousedev: PS/2 mouse device common for all mice
[ 4.489167] i2c /dev entries driver
[ 4.493882] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.499514] usbcore: registered new interface driver usbhid
[ 4.505062] usbhid: USB HID core driver
[ 4.510149] NET: Registered protocol family 10
[ 4.515993] Segment Routing with IPv6
[ 4.519897] sda: sda1
[ 4.519951] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 4.524206] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.529966] NET: Registered protocol family 17
[ 4.537469] Key type dns_resolver registered
[ 4.542891] registered taskstats version 1
[ 4.547041] Loading compiled-in X.509 certificates
[ 4.551910] zswap: loaded using pool lzo/zbud
[ 4.632616] Key type big_key registered
[ 4.673561] Key type encrypted registered
[ 4.679759] hctosys: unable to open rtc device (rtc0)
[ 4.686860] Freeing unused kernel memory: 1024K
Loading, please wait...
starting version 232
[ 4.914606] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 4.923292] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 4.930800] random: systemd-udevd: uninitialized urandom read (16 bytes read)
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
No root device specified. Boot arguments must include a root= parameter.
BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash)
Enter 'help' for a list of built-in commands.
(initramfs)
(initramfs)
(initramfs) pwd
/
(initramfs) ps
PID USER COMMAND
1 0 {init} /bin/sh /init
2 0 [kthreadd]
3 0 [kworker/0:0]
4 0 [kworker/0:0H]
5 0 [kworker/u4:0]
6 0 [mm_percpu_wq]
7 0 [ksoftirqd/0]
8 0 [rcu_preempt]
9 0 [rcu_sched]
10 0 [rcu_bh]
11 0 [migration/0]
12 0 [cpuhp/0]
13 0 [cpuhp/1]
14 0 [migration/1]
15 0 [ksoftirqd/1]
16 0 [kworker/1:0]
17 0 [kworker/1:0H]
18 0 [kdevtmpfs]
19 0 [netns]
20 0 [kworker/0:1]
21 0 [oom_reaper]
22 0 [writeback]
23 0 [kcompactd0]
24 0 [crypto]
25 0 [kblockd]
26 0 [ata_sff]
27 0 [rpciod]
28 0 [xprtiod]
29 0 [kswapd0]
30 0 [kworker/u5:0]
31 0 [nfsiod]
54 0 [kworker/u4:1]
65 0 [scsi_eh_0]
6[ 49.771619] random: fast init done
6 0 [scsi_tmf_0]
67 0 [kworker/u4:2]
69 0 [kworker/1:1]
71 0 [ipv6_addrconf]
103 0 /lib/systemd/systemd-udevd --daemon --resolve-names=never
113 0 [kworker/0:1H]
114 0 [kworker/1:1H]
118 0 sh -i
119 0 ps
(initramfs) ls -al
total 8
drwxr-xr-x 13 0 0 340 Jan 1 00:00 .
drwxr-xr-x 13 0 0 340 Jan 1 00:00 ..
lrwxrwxrwx 1 0 0 7 May 15 2020 bin -> usr/bin
drwxr-xr-x 3 0 0 100 May 15 2020 conf
drwxr-xr-x 9 0 0 2420 Jan 1 00:00 dev
drwxr-xr-x 5 0 0 180 May 15 2020 etc
-rwxr-xr-x 1 0 0 6338 Aug 23 2019 init
lrwxrwxrwx 1 0 0 7 May 15 2020 lib -> usr/lib
dr-xr-xr-x 53 0 0 0 Jan 1 00:00 proc
drwx------ 2 0 0 40 May 13 2020 root
drwxr-xr-x 4 0 0 80 Jan 1 00:00 run
lrwxrwxrwx 1 0 0 8 May 15 2020 sbin -> usr/sbin
drwxr-xr-x 5 0 0 160 May 15 2020 scripts
dr-xr-xr-x 12 0 0 0 Jan 1 00:00 sys
drwxr-xr-x 2 0 0 40 Jan 1 00:00 tmp
drwxr-xr-x 5 0 0 100 May 15 2020 usr
drwxr-xr-x 3 0 0 60 Jan 1 00:00 var
(initramfs)
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 26, 2023 04:35PM |
Registered: 9 months ago Posts: 82 |
OX820 # printenv dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr autoload=no baudrate=115200 bootargs=console=ttyS0,115200n8 bootcmd=run dt_bootcmd_ide bootdelay=3 console=console=ttyS0,115200n8 dt_bootcmd_ide=ide start; run dt_ide_bootcmd; ide stop; reset dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot dt_ide_load_dtb=ext2load ide 0:1 0x62c00000 /boot/dts/ox820-pogoplug-classic.dtb dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage dt_load_dtb=ext2load usb 0:1 0x62c00000 /boot/dts/ox820-akitio.dtb dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage dt_sata_boot=ext2load ide 0:1 0x60500000 /boot/uImage; bootm 0x60500000 dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot dtb_addr=0x62c00000 ethact=mii0 ethaddr=00:30:E0:00:00:01 ide_set_bootargs=setenv bootargs root=LABEL=rootfs rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes if_netconsole=ping $serverip ipaddr=192.168.0.100 mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) preboot_nc=run if_netconsole start_netconsole sata_bootcmd=run usb_set_bootargs; run sata_boot start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version stderr=serial stdin=serial stdout=serial uimage_addr=0x60500000 uinitrd_addr=0x60e00000 usb_device=0:1 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10 Environment size: 1936/16380 bytes OX820 # run ide_set_bootargs; run dt_ide_boot 4600448 bytes read in 1676 ms (2.6 MiB/s) 6464907 bytes read in 2321 ms (2.7 MiB/s) 8892 bytes read in 43 ms (201.2 KiB/s) ## Booting kernel from Legacy Image at 60500000 ... Image Name: Linux-4.14.180-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4600384 Bytes = 4.4 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 60e00000 ... Image Name: initramfs-4.14.180-oxnas-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6464843 Bytes = 6.2 MiB Load Address: 60000000 Entry Point: 60000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 62c00000 Booting using the fdt blob at 0x62c00000 Loading Kernel Image ... OK Loading Ramdisk to 6f7fe000, end 6fe2854b ... OK Loading Device Tree to 6f7f8000, end 6f7fd2bb ... OK Led: GREEN Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020 [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Pogoplug V3 Classic [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: root=LABEL=rootfs rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 242664K/262144K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 19480K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0800000 (8160 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b31f68 ( 200 kB) [ 0.000000] .bss : 0xc0b383b8 - 0xc0b757c0 ( 246 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] FPGA IRQ chip 0 "interrupt-controller" @ d0804000, 32 irqs, parent IRQ: 16 [ 0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.000048] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.000064] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.000087] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.000235] GIC: PPI13 is secure or misconfigured [ 0.000289] GIC: PPI13 is secure or misconfigured [ 0.000455] Console: colour dummy device 80x30 [ 0.000499] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.050383] pid_max: default: 32768 minimum: 301 [ 0.050649] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.050675] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.051568] CPU: Testing write buffer coherency: ok [ 0.090442] Setting up static identity map for 0x60100000 - 0x60100038 [ 0.110343] Hierarchical SRCU implementation. [ 0.150343] smp: Bringing up secondary CPUs ... [ 0.220451] GIC: PPI13 is secure or misconfigured [ 0.280632] smp: Brought up 1 node, 2 CPUs [ 0.280660] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.281397] devtmpfs: initialized [ 0.287052] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.287088] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.287418] prandom: seed boundary self test passed [ 0.291706] prandom: 100 self tests passed [ 0.291724] pinctrl core: initialized pinctrl subsystem [ 0.292423] NET: Registered protocol family 16 [ 0.294100] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.296629] cpuidle: using governor ladder [ 0.296704] cpuidle: using governor menu [ 0.314193] vgaarb: loaded [ 0.314698] SCSI subsystem initialized [ 0.315389] usbcore: registered new interface driver usbfs [ 0.315494] usbcore: registered new interface driver hub [ 0.315650] usbcore: registered new device driver usb [ 0.315834] pps_core: LinuxPPS API ver. 1 registered [ 0.315852] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.315891] PTP clock support registered [ 0.317017] clocksource: Switched to clocksource oxnas_rps_clocksource_timer [ 0.332833] NET: Registered protocol family 2 [ 0.333744] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.333795] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.333852] TCP: Hash tables configured (established 2048 bind 2048) [ 0.334013] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.334059] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.334325] NET: Registered protocol family 1 [ 0.335088] RPC: Registered named UNIX socket transport module. [ 0.335111] RPC: Registered udp transport module. [ 0.335124] RPC: Registered tcp transport module. [ 0.335137] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.335511] Unpacking initramfs... [ 1.042936] Freeing initrd memory: 6316K [ 1.062184] Initialise system trusted keyrings [ 1.062251] Key type blacklist registered [ 1.062517] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 1.069857] zbud: loaded [ 1.074257] NFS: Registering the id_resolver key type [ 1.074306] Key type id_resolver registered [ 1.074319] Key type id_legacy registered [ 1.074344] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.074360] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.075171] fuse init (API version 7.26) [ 1.076070] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.076328] orangefs_init: module version upstream loaded [ 3.059143] Key type asymmetric registered [ 3.059166] Asymmetric key parser 'x509' registered [ 3.059269] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 3.059287] io scheduler noop registered [ 3.059299] io scheduler deadline registered [ 3.059361] io scheduler cfq registered (default) [ 3.061007] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 3.062407] console [ttyS0] disabled [ 3.062551] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A [ 3.640670] console [ttyS0] enabled [ 3.654666] loop: module loaded [ 3.659694] scsi host0: sata_oxnas [ 3.663406] ata1: SATA max UDMA/133 irq 57 [ 3.667642] sata_oxnas: resetting SATA core [ 3.737361] nand: Could not find valid ONFI parameter page; aborting [ 3.743697] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 3.750072] nand: Hynix NAND 256MiB 3,3V 8-bit [ 3.754501] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 3.762081] Scanning device for bad blocks [ 3.932249] 2 ofpart partitions found on MTD device 41000000.nand-controller [ 3.939297] Creating 2 MTD partitions on "41000000.nand-controller": [ 3.945630] 0x000000000000-0x000000e00000 : "boot" [ 3.951971] 0x000000e00000-0x000008000000 : "data" [ 3.959769] libphy: Fixed MDIO Bus: probed [ 3.964272] oxnas-dwmac 40400000.ethernet: PTP uses main clock [ 3.970145] oxnas-dwmac 40400000.ethernet: no reset control found [ 4.037120] stmmac - user ID: 0x12, Synopsys ID: 0x35 [ 4.042158] oxnas-dwmac 40400000.ethernet: Ring mode enabled [ 4.047846] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported [ 4.055121] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors [ 4.061913] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors [ 4.068531] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported [ 4.075809] oxnas-dwmac 40400000.ethernet: COE Type 2 [ 4.080865] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported [ 4.087825] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported [ 4.094074] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 4.155642] libphy: stmmac: probed [ 4.159101] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 4.168596] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL) [ 4.179036] PPP generic driver version 2.4.2 [ 4.183569] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.187069] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 4.190144] ehci-pci: EHCI PCI platform driver [ 4.200954] ata1.00: ATA-8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133 [ 4.208181] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 4.215772] ata1.00: configured for UDMA/133 [ 4.220651] scsi 0:0:0:0: Direct-Access ATA APPLE HDD HTS547 D70F PQ: 0 ANSI: 5 [ 4.230374] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.237885] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.243205] sd 0:0:0:0: [sda] Write Protect is off [ 4.248256] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.407088] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 4.412600] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 4.420456] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100 [ 4.447086] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 4.453393] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.460213] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.467438] usb usb1: Product: EHCI Host Controller [ 4.472291] usb usb1: Manufacturer: Linux 4.14.180-oxnas-tld-1 ehci_hcd [ 4.478909] usb usb1: SerialNumber: 40200100.ehci [ 4.484405] hub 1-0:1.0: USB hub found [ 4.488320] hub 1-0:1.0: 2 ports detected [ 4.493299] usbcore: registered new interface driver cdc_wdm [ 4.499156] usbcore: registered new interface driver usb-storage [ 4.505272] usbcore: registered new interface driver usbserial [ 4.511280] usbcore: registered new interface driver usbserial_generic [ 4.517882] usbserial: USB Serial support registered for generic [ 4.524172] mousedev: PS/2 mouse device common for all mice [ 4.529960] i2c /dev entries driver [ 4.534691] hidraw: raw HID events driver (C) Jiri Kosina [ 4.540362] sda: sda1 [ 4.540454] usbcore: registered new interface driver usbhid [ 4.548423] usbhid: USB HID core driver [ 4.550213] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.553546] NET: Registered protocol family 10 [ 4.562836] Segment Routing with IPv6 [ 4.566566] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.574133] NET: Registered protocol family 17 [ 4.578736] Key type dns_resolver registered [ 4.584330] registered taskstats version 1 [ 4.588477] Loading compiled-in X.509 certificates [ 4.593351] zswap: loaded using pool lzo/zbud [ 4.674181] Key type big_key registered [ 4.714741] Key type encrypted registered [ 4.720826] hctosys: unable to open rtc device (rtc0) [ 4.727905] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 4.957911] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 4.966499] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 4.974036] random: systemd-udevd: uninitialized urandom read (16 bytes read) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 11.253235] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 11.414950] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 11.876764] random: fast init done INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 16.863127] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.29.2 rootfs: Group descriptor 0 marked uninitialized without feature set. FIXED. [ 20.549393] random: crng init done / 19.8% [ 20.552788] random: 7 urandom warning(s) missed due to ratelimiting rootfs: 26489/122880 files (0.2% non-contiguous), 234757/1955904 blocks done. [ 29.176832] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [....] Checking file systems...fsck from util-linux 2.29.2 done. [ ok ] Cleaning up temporary files.... [ ok ] Loading kernel modules...done. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ [ 32.951370] oxnas-dwmac 40400000.ethernet eth0: No phy led trigger registered for speed(-1) [ 32.959772] Generic PHY stmmac-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 32.974016] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 32.985886] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock [ 32.992977] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Listening on LPF/eth0/00:30:e0:00:00:01 Sending on LPF/eth0/00:30:e0:00:00:01 Sending on Socket/fallback DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 [ 34.008000] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 34.016435] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 DHCPNAK from 192.168.20.253 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPREQUEST of 192.168.30.12 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 192.168.30.12 from 192.168.20.253 DHCPACK of 192.168.30.12 from 192.168.20.253 bound to 192.168.30.12 -- renewal in 39845 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1208 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1235 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. Debian GNU/Linux 10 iSharing ttyS0 iSharing login: root Password: Last login: Wed Dec 31 16:01:35 PST 1969 from 192.168.0.100 on pts/0 Linux iSharing 4.14.180-oxnas-tld-1 #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020 armv6l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@iSharing:~#
root@iSharing:/# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020 [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Pogoplug V3 Classic [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] free_area_init_node: node 0, pgdat c0b30540, node_mem_map cf5f8000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440 [ 0.000000] pcpu-alloc: s29548 r8192 d23700 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: root=LABEL=rootfs rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 242664K/262144K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 19480K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0800000 (8160 kB) .init : 0xc0a00000 - 0xc0b00000 (1024 kB) .data : 0xc0b00000 - 0xc0b31f68 ( 200 kB) .bss : 0xc0b383b8 - 0xc0b757c0 ( 246 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] FPGA IRQ chip 0 "interrupt-controller" @ d0804000, 32 irqs, parent IRQ: 16 [ 0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.000048] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.000064] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.000087] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.000235] GIC: PPI13 is secure or misconfigured [ 0.000289] GIC: PPI13 is secure or misconfigured [ 0.000455] Console: colour dummy device 80x30 [ 0.000499] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.050383] pid_max: default: 32768 minimum: 301 [ 0.050649] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.050675] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.051568] CPU: Testing write buffer coherency: ok [ 0.090442] Setting up static identity map for 0x60100000 - 0x60100038 [ 0.110343] Hierarchical SRCU implementation. [ 0.150343] smp: Bringing up secondary CPUs ... [ 0.220451] GIC: PPI13 is secure or misconfigured [ 0.280632] smp: Brought up 1 node, 2 CPUs [ 0.280660] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.281397] devtmpfs: initialized [ 0.287052] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.287088] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.287418] prandom: seed boundary self test passed [ 0.291706] prandom: 100 self tests passed [ 0.291724] pinctrl core: initialized pinctrl subsystem [ 0.292423] NET: Registered protocol family 16 [ 0.294100] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.296629] cpuidle: using governor ladder [ 0.296704] cpuidle: using governor menu [ 0.314193] vgaarb: loaded [ 0.314698] SCSI subsystem initialized [ 0.315036] libata version 3.00 loaded. [ 0.315389] usbcore: registered new interface driver usbfs [ 0.315494] usbcore: registered new interface driver hub [ 0.315650] usbcore: registered new device driver usb [ 0.315834] pps_core: LinuxPPS API ver. 1 registered [ 0.315852] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.315891] PTP clock support registered [ 0.317017] clocksource: Switched to clocksource oxnas_rps_clocksource_timer [ 0.332833] NET: Registered protocol family 2 [ 0.333744] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.333795] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.333852] TCP: Hash tables configured (established 2048 bind 2048) [ 0.334013] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.334059] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.334325] NET: Registered protocol family 1 [ 0.335088] RPC: Registered named UNIX socket transport module. [ 0.335111] RPC: Registered udp transport module. [ 0.335124] RPC: Registered tcp transport module. [ 0.335137] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.335155] PCI: CLS 0 bytes, default 32 [ 0.335511] Unpacking initramfs... [ 1.042936] Freeing initrd memory: 6316K [ 1.062184] Initialise system trusted keyrings [ 1.062251] Key type blacklist registered [ 1.062517] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 1.069857] zbud: loaded [ 1.074257] NFS: Registering the id_resolver key type [ 1.074306] Key type id_resolver registered [ 1.074319] Key type id_legacy registered [ 1.074344] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.074360] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.075171] fuse init (API version 7.26) [ 1.076070] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.076328] orangefs_init: module version upstream loaded [ 3.059143] Key type asymmetric registered [ 3.059166] Asymmetric key parser 'x509' registered [ 3.059269] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 3.059287] io scheduler noop registered [ 3.059299] io scheduler deadline registered [ 3.059361] io scheduler cfq registered (default) [ 3.061007] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 3.062407] console [ttyS0] disabled [ 3.062551] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A [ 3.640670] console [ttyS0] enabled [ 3.654666] loop: module loaded [ 3.659694] scsi host0: sata_oxnas [ 3.663406] ata1: SATA max UDMA/133 irq 57 [ 3.667642] sata_oxnas: resetting SATA core [ 3.737361] nand: Could not find valid ONFI parameter page; aborting [ 3.743697] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 3.750072] nand: Hynix NAND 256MiB 3,3V 8-bit [ 3.754501] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 3.762081] Scanning device for bad blocks [ 3.932249] 2 ofpart partitions found on MTD device 41000000.nand-controller [ 3.939297] Creating 2 MTD partitions on "41000000.nand-controller": [ 3.945630] 0x000000000000-0x000000e00000 : "boot" [ 3.951971] 0x000000e00000-0x000008000000 : "data" [ 3.959769] libphy: Fixed MDIO Bus: probed [ 3.964272] oxnas-dwmac 40400000.ethernet: PTP uses main clock [ 3.970145] oxnas-dwmac 40400000.ethernet: no reset control found [ 4.037120] stmmac - user ID: 0x12, Synopsys ID: 0x35 [ 4.042158] oxnas-dwmac 40400000.ethernet: Ring mode enabled [ 4.047846] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported [ 4.055121] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors [ 4.061913] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors [ 4.068531] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported [ 4.075809] oxnas-dwmac 40400000.ethernet: COE Type 2 [ 4.080865] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported [ 4.087825] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported [ 4.094074] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 4.155642] libphy: stmmac: probed [ 4.159101] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 4.168596] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL) [ 4.179036] PPP generic driver version 2.4.2 [ 4.183569] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.187069] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 4.190144] ehci-pci: EHCI PCI platform driver [ 4.200954] ata1.00: ATA-8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133 [ 4.208181] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 4.215772] ata1.00: configured for UDMA/133 [ 4.220651] scsi 0:0:0:0: Direct-Access ATA APPLE HDD HTS547 D70F PQ: 0 ANSI: 5 [ 4.230374] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.237885] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.243205] sd 0:0:0:0: [sda] Write Protect is off [ 4.248035] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.248256] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.407088] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 4.412600] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 4.420456] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100 [ 4.447086] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 4.453393] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.460213] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.467438] usb usb1: Product: EHCI Host Controller [ 4.472291] usb usb1: Manufacturer: Linux 4.14.180-oxnas-tld-1 ehci_hcd [ 4.478909] usb usb1: SerialNumber: 40200100.ehci [ 4.484405] hub 1-0:1.0: USB hub found [ 4.488320] hub 1-0:1.0: 2 ports detected [ 4.493299] usbcore: registered new interface driver cdc_wdm [ 4.499156] usbcore: registered new interface driver usb-storage [ 4.505272] usbcore: registered new interface driver usbserial [ 4.511280] usbcore: registered new interface driver usbserial_generic [ 4.517882] usbserial: USB Serial support registered for generic [ 4.524172] mousedev: PS/2 mouse device common for all mice [ 4.529960] i2c /dev entries driver [ 4.534691] hidraw: raw HID events driver (C) Jiri Kosina [ 4.540362] sda: sda1 [ 4.540454] usbcore: registered new interface driver usbhid [ 4.548423] usbhid: USB HID core driver [ 4.550213] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.553546] NET: Registered protocol family 10 [ 4.562836] Segment Routing with IPv6 [ 4.566566] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.574133] NET: Registered protocol family 17 [ 4.578736] Key type dns_resolver registered [ 4.584330] registered taskstats version 1 [ 4.588477] Loading compiled-in X.509 certificates [ 4.593351] zswap: loaded using pool lzo/zbud [ 4.674181] Key type big_key registered [ 4.714741] Key type encrypted registered [ 4.720826] hctosys: unable to open rtc device (rtc0) [ 4.727905] Freeing unused kernel memory: 1024K [ 4.957911] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 4.966499] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 4.974036] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 11.253235] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 11.414950] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 11.876764] random: fast init done [ 16.863127] EXT4-fs (sda1): re-mounted. Opts: (null) [ 20.549393] random: crng init done [ 20.552788] random: 7 urandom warning(s) missed due to ratelimiting [ 29.176832] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 32.951370] oxnas-dwmac 40400000.ethernet eth0: No phy led trigger registered for speed(-1) [ 32.959772] Generic PHY stmmac-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 32.974016] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 32.985886] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock [ 32.992977] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 34.008000] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 34.016435] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready root@iSharing:/#
NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x000000000000-0x0000026c0000 : "Boot partition" 0x0000026c0000-0x000010000000 : "Data Partition" UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI warning: ubi_eba_init_scan: cannot reserve enough PEBs for bad PEB handling, reserved 11, need 17 UBI: attached mtd2 to ubi0 UBI: MTD device name: "Data Partition" UBI: MTD device size: 217 MiB UBI: number of good PEBs: 1738 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 1738 UBI: number of PEBs reserved for bad PEB handling: 11 UBI: max/mean erase counter: 800/105 UBI: image sequence number: 1359814330 UBI: background thread "ubi_bgt0d" started, PID 398
[ 3.932249] 2 ofpart partitions found on MTD device 41000000.nand-controller [ 3.939297] Creating 2 MTD partitions on "41000000.nand-controller": [ 3.945630] 0x000000000000-0x000000e00000 : "boot" [ 3.951971] 0x000000e00000-0x000008000000 : "data"
root@iSharing:/# apt install xfsprogs Reading package lists... Done Building dependency tree Reading state information... Done The following additional packages will be installed: libicu63 libmpdec2 libncursesw6 libpython3-stdlib libpython3.7-minimal libpython3.7-stdlib libreadline5 libtinfo6 mime-support python3 python3-minimal python3.7 python3.7-minimal Suggested packages: python3-doc python3-tk python3-venv python3.7-venv python3.7-doc binutils binfmt-support xfsdump acl attr quota Recommended packages: libgpm2 file The following NEW packages will be installed: libicu63 libmpdec2 libncursesw6 libpython3-stdlib libpython3.7-minimal libpython3.7-stdlib libreadline5 libtinfo6 mime-support python3 python3-minimal python3.7 python3.7-minimal xfsprogs 0 upgraded, 14 newly installed, 0 to remove and 59 not upgraded. Need to get 12.0 MB/13.6 MB of archives. After this operation, 57.4 MB of additional disk space will be used. Do you want to continue? [Y/n] Y Err:1 http://ftp.us.debian.org/debian buster/main armel libpython3.7-minimal armel 3.7.3-2+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:2 http://ftp.us.debian.org/debian buster/main armel python3.7-minimal armel 3.7.3-2+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:3 http://ftp.us.debian.org/debian buster/main armel libpython3.7-stdlib armel 3.7.3-2+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:4 http://ftp.us.debian.org/debian buster/main armel python3.7 armel 3.7.3-2+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:5 http://ftp.us.debian.org/debian buster/main armel libicu63 armel 63.1-6+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:5 http://security.debian.org buster/updates/main armel libicu63 armel 63.1-6+deb10u1 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/p/python3.7/libpython3.7-minimal_3.7.3-2+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/p/python3.7/python3.7-minimal_3.7.3-2+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/p/python3.7/libpython3.7-stdlib_3.7.3-2+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/p/python3.7/python3.7_3.7.3-2+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://security.debian.org/pool/updates/main/i/icu/libicu63_63.1-6+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing?
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 26, 2023 05:49PM |
Admin Registered: 13 years ago Posts: 18,821 |
[ 3.737361] nand: Could not find valid ONFI parameter page; aborting [ 32.951370] oxnas-dwmac 40400000.ethernet eth0: No phy led trigger registered for speed(-1)The above are not errors. Just warnings, and safe to ignore.
[ 3.932249] 2 ofpart partitions found on MTD device 41000000.nand-controller [ 3.939297] Creating 2 MTD partitions on "41000000.nand-controller": [ 3.945630] 0x000000000000-0x000000e00000 : "boot" [ 3.951971] 0x000000e00000-0x000008000000 : "data"
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 26, 2023 09:19PM |
Registered: 9 months ago Posts: 82 |
Linux iSharing 4.14.180-oxnas-tld-1 #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020 armv6l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Wed Dec 31 16:00:57 1969 root@iSharing:~# root@iSharing:~# root@iSharing:~# cd /boot root@iSharing:/boot# ls -al total 42692 drwxr-xr-x 3 root root 4096 Nov 26 2023 . drwxrwxrwx 21 root root 4096 Nov 26 2023 .. -rw-r--r-- 1 root root 142138 Nov 26 2023 config-5.4.224-oxnas-tld-1 drwxr-xr-x 2 root root 4096 Nov 26 2023 dts -rw-r--r-- 1 root root 160176 Nov 26 2023 linux-5.4.224-oxnas-tld-1.patch -rw-r--r-- 1 root root 61440 Nov 26 2023 linux-dtb-5.4.224-oxnas-tld-1.tar -rw-r--r-- 1 root root 11289280 Nov 26 2023 linux-headers-5.4.224-oxnas-tld-1_1.0_armel.deb -rw-r--r-- 1 root root 14710632 Nov 26 2023 linux-image-5.4.224-oxnas-tld-1_1.0_armel.deb -rwxr-xr-x 1 root root 32120 Nov 26 2023 u-boot-spl.bin -rwxr-xr-x 1 root root 16384 Dec 31 16:00 u-boot.env -rw-r--r-- 1 root root 525880 Nov 26 2023 u-boot.img -rw-r--r-- 1 root root 4600448 Nov 26 2023 uImage -rw-r--r-- 1 root root 6464907 Nov 26 2023 uInitrd -rwxr-xr-x 1 root root 5589592 Nov 26 2023 zImage-5.4.224-oxnas-tld-1 root@iSharing:/boot# dpkg -i linux-image-5.4.224-oxnas-tld-1_1.0_armel.deb Selecting previously unselected package linux-image-5.4.224-oxnas-tld-1. (Reading database ... 12123 files and directories currently installed.) Preparing to unpack linux-image-5.4.224-oxnas-tld-1_1.0_armel.deb ... Unpacking linux-image-5.4.224-oxnas-tld-1 (1.0) ... Setting up linux-image-5.4.224-oxnas-tld-1 (1.0) ... update-initramfs: Generating /boot/initrd.img-5.4.224-oxnas-tld-1 root@iSharing:/boot# mv uImage uImage.bak root@iSharing:/boot# mv uInitrd uInitrd.bak root@iSharing:/boot# mkimage -A arm -O linux -T kernel -C none -a 0x60008000 -e 0x60008000 -n Linux-5.4.224-oxnas-tld-1 -d vmlinuz-5.4.224-oxnas-tld-1 uImage Image Name: Linux-5.4.224-oxnas-tld-1 Created: Sun Nov 26 19:11:08 2023 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5589592 Bytes = 5458.59 KiB = 5.33 MiB Load Address: 60008000 Entry Point: 60008000 root@iSharing:/boot# mkimage -A arm -O linux -T ramdisk -C gzip -a 0x60000000 -e 0x60000000 -n initramfs-5.4.224-oxnas-tld-1 -d initrd.img-5.4.224-oxnas-tld-1 uInitrd Image Name: initramfs-5.4.224-oxnas-tld-1 Created: Sun Nov 26 19:11:17 2023 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6497712 Bytes = 6345.42 KiB = 6.20 MiB Load Address: 60000000 Entry Point: 60000000 root@iSharing:/boot# sync;sync;sync root@iSharing:/boot# ls -al total 67940 drwxr-xr-x 3 root root 4096 Nov 26 19:32 . drwxrwxrwx 21 root root 4096 Nov 26 19:04 .. -rw-r--r-- 1 root root 1617241 Nov 14 2022 System.map-5.4.224-oxnas-tld-1 -rw-r--r-- 1 root root 142138 Nov 14 2022 config-5.4.224-oxnas-tld-1 drwxr-xr-x 2 root root 4096 Nov 26 18:38 dts -rw-r--r-- 1 root root 6497712 Nov 26 19:10 initrd.img-5.4.224-oxnas-tld-1 -rw-r--r-- 1 root root 160176 Nov 26 18:38 linux-5.4.224-oxnas-tld-1.patch -rw-r--r-- 1 root root 61440 Nov 26 18:38 linux-dtb-5.4.224-oxnas-tld-1.tar -rw-r--r-- 1 root root 11289280 Nov 26 18:38 linux-headers-5.4.224-oxnas-tld-1_1.0_armel.deb -rw-r--r-- 1 root root 14710632 Nov 26 18:38 linux-image-5.4.224-oxnas-tld-1_1.0_armel.deb -rwxr-xr-x 1 root root 32120 Nov 26 18:38 u-boot-spl.bin -rwxr-xr-x 1 root root 16384 Dec 31 1969 u-boot.env -rw-r--r-- 1 root root 525880 Nov 26 18:38 u-boot.img -rw-r--r-- 1 root root 5589656 Nov 26 19:11 uImage -rw-r--r-- 1 root root 4600448 Nov 26 19:03 uImage.bak -rw-r--r-- 1 root root 6497776 Nov 26 19:11 uInitrd -rw-r--r-- 1 root root 6464907 Nov 26 19:03 uInitrd.bak -rwxr-xr-x 1 root root 5589592 Nov 14 2022 vmlinuz-5.4.224-oxnas-tld-1 -rwxr-xr-x 1 root root 5589592 Nov 26 18:38 zImage-5.4.224-oxnas-tld-1 root@iSharing:/boot# reboot Broadcast message from root@iSharing (pts/0) (Sun Nov 26 19:11:45 2023): The system is going down for reboot NOW! root@iSharing:/boot#
OX820 # printenv dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr autoload=no baudrate=115200 bootargs=console=ttyS0,115200n8 bootcmd=run dt_bootcmd_ide bootdelay=3 console=console=ttyS0,115200n8 dt_bootcmd_ide=ide start; run dt_ide_bootcmd; ide stop; reset dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot dt_ide_load_dtb=ext2load ide 0:1 0x62c00000 /boot/dts/ox820-pogoplug-classic.dtb dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage dt_load_dtb=ext2load usb 0:1 0x62c00000 /boot/dts/ox820-pogoplug-classic.dtb dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage dt_sata_boot=ext2load ide 0:1 0x60500000 /boot/uImage; bootm 0x60500000 dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot dtb_addr=0x62c00000 ethact=mii0 ethaddr=00:30:E0:00:00:01 ide_set_bootargs=setenv bootargs root=LABEL=rootfs rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes if_netconsole=ping $serverip ipaddr=192.168.0.100 mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) preboot_nc=run if_netconsole start_netconsole sata_bootcmd=run usb_set_bootargs; run sata_boot start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version stderr=serial stdin=serial stdout=serial uimage_addr=0x60500000 uinitrd_addr=0x60e00000 usb_device=0:1 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10 Environment size: 1946/16380 bytes OX820 # saveenv Saving Environment to EXT4... File System is consistent file found deleting update journal finished File System is consistent update journal finished done OX820 # run ide_set_bootargs; run dt_ide_boot 5589656 bytes read in 2055 ms (2.6 MiB/s) 6497791 bytes read in 2347 ms (2.6 MiB/s) 8588 bytes read in 49 ms (170.9 KiB/s) ## Booting kernel from Legacy Image at 60500000 ... Image Name: Linux-5.4.224-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5589592 Bytes = 5.3 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 60e00000 ... Image Name: initramfs-5.4.224-oxnas-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6497727 Bytes = 6.2 MiB Load Address: 60000000 Entry Point: 60000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 62c00000 Booting using the fdt blob at 0x62c00000 Loading Kernel Image ... OK Loading Ramdisk to 6f7f6000, end 6fe285bf ... OK Loading Device Tree to 6f7f0000, end 6f7f518b ... OK Led: GREEN Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.4.224-oxnas-tld-1 (root@tldDebian) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1.0 SMP PREEMPT Mon Nov 14 15:48:26 PST 2022 [ 0.000000][ T0] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Pogoplug V3 Classic [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] percpu: Embedded 15 pages/cpu s30636 r8192 d22612 u61440 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: root=LABEL=rootfs rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 240568K/262144K available (8192K kernel code, 234K rwdata, 2068K rodata, 1024K init, 258K bss, 21576K reserved, 0K cma-reserved) [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16 [ 0.000017][ T0] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.000051][ T0] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.000069][ T0] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.000094][ T0] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.000250][ T0] GIC: PPI13 is secure or misconfigured [ 0.000307][ T0] GIC: PPI13 is secure or misconfigured [ 0.000624][ T0] Console: colour dummy device 80x30 [ 0.000698][ T0] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.050396][ T0] pid_max: default: 32768 minimum: 301 [ 0.051105][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051130][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051404][ T0] *** VALIDATE tmpfs *** [ 0.052766][ T0] *** VALIDATE proc *** [ 0.052992][ T0] *** VALIDATE cgroup1 *** [ 0.053015][ T0] *** VALIDATE cgroup2 *** [ 0.053212][ T0] CPU: Testing write buffer coherency: ok [ 0.055677][ T1] Setting up static identity map for 0x60100000 - 0x60100038 [ 0.056012][ T1] rcu: Hierarchical SRCU implementation. [ 0.057034][ T1] smp: Bringing up secondary CPUs ... [ 0.058288][ T0] GIC: PPI13 is secure or misconfigured [ 0.110661][ T1] smp: Brought up 1 node, 2 CPUs [ 0.110702][ T1] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.111897][ T1] devtmpfs: initialized [ 0.118417][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.118474][ T1] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.118673][ T1] prandom: seed boundary self test passed [ 0.122982][ T1] prandom: 100 self tests passed [ 0.123002][ T1] pinctrl core: initialized pinctrl subsystem [ 0.125109][ T1] NET: Registered protocol family 16 [ 0.126919][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130091][ T1] cpuidle: using governor ladder [ 0.130170][ T1] cpuidle: using governor menu [ 6.079173][ T1] vgaarb: loaded [ 6.080128][ T1] SCSI subsystem initialized [ 6.081113][ T1] usbcore: registered new interface driver usbfs [ 6.081203][ T1] usbcore: registered new interface driver hub [ 6.081344][ T1] usbcore: registered new device driver usb [ 6.081584][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.081602][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.081638][ T1] PTP clock support registered [ 6.083453][ T1] clocksource: Switched to clocksource oxnas_rps_clocksource_timer [ 6.083512][ T1] *** VALIDATE bpf *** [ 6.084042][ T1] *** VALIDATE ramfs *** [ 6.103982][ T1] NET: Registered protocol family 2 [ 6.104253][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 6.105354][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 6.105664][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.105728][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 6.105784][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 6.106022][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 6.106076][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 6.106385][ T1] NET: Registered protocol family 1 [ 6.107663][ T1] RPC: Registered named UNIX socket transport module. [ 6.107688][ T1] RPC: Registered udp transport module. [ 6.107704][ T1] RPC: Registered tcp transport module. [ 6.107719][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 6.107742][ T1] PCI: CLS 0 bytes, default 32 [ 6.108211][ T1] Unpacking initramfs... [ 6.844638][ T1] Freeing initrd memory: 6348K [ 6.846082][ T1] Initialise system trusted keyrings [ 6.846205][ T1] Key type blacklist registered [ 6.846663][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 6.858375][ T1] zbud: loaded [ 6.864645][ T1] NFS: Registering the id_resolver key type [ 6.864716][ T1] Key type id_resolver registered [ 6.864732][ T1] Key type id_legacy registered [ 6.864765][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.864780][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 6.864793][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.866181][ T1] fuse: init (API version 7.31) [ 6.866455][ T1] *** VALIDATE fuse *** [ 6.866483][ T1] *** VALIDATE fuse *** [ 6.867358][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.867737][ T1] orangefs_init: module version upstream loaded [ 6.915074][ T1] Key type asymmetric registered [ 6.915107][ T1] Asymmetric key parser 'x509' registered [ 6.915202][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 6.922316][ T1] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 6.923988][ T1] printk: console [ttyS0] disabled [ 6.924162][ T1] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A [ 7.564981][ T1] printk: console [ttyS0] enabled [ 7.585149][ T1] loop: module loaded [ 7.591370][ T1] scsi host0: sata_oxnas [ 7.596259][ T1] ata1: SATA max UDMA/133 irq 57 [ 7.601159][ T75] sata_oxnas: resetting SATA core [ 7.663800][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it [ 7.673213][ T1] ONFI parameter recovery failed, aborting [ 7.678924][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 7.685980][ T1] nand: Hynix NAND 256MiB 3,3V 8-bit [ 7.691100][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.699376][ T1] Scanning device for bad blocks [ 7.868833][ T1] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller [ 7.877437][ T1] Creating 2 MTD partitions on "41000000.nand-controller": [ 7.884554][ T1] 0x000000000000-0x000000e00000 : "boot" [ 7.891077][ T1] 0x000000e00000-0x000008000000 : "data" [ 7.898631][ T1] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found [ 7.905500][ T1] oxnas-dwmac 40400000.ethernet: PTP uses main clock [ 7.912012][ T1] oxnas-dwmac 40400000.ethernet: no reset control found [ 7.983964][ T1] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35 [ 7.991605][ T1] oxnas-dwmac 40400000.ethernet: DWMAC1000 [ 7.997391][ T1] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported [ 8.005399][ T1] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported [ 8.013368][ T1] oxnas-dwmac 40400000.ethernet: COE Type 2 [ 8.019120][ T1] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported [ 8.026688][ T1] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported [ 8.033658][ T1] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors [ 8.041105][ T1] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors [ 8.048414][ T1] oxnas-dwmac 40400000.ethernet: Ring mode enabled [ 8.054791][ T1] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 8.108730][ T1] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 8.118947][ T1] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL) [ 8.123517][ T75] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 8.130227][ T1] PPP generic driver version 2.4.2 [ 8.141352][ T75] ata1.00: ATA-8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133 [ 8.141386][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.149242][ T75] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 8.163840][ T1] ehci-pci: EHCI PCI platform driver [ 8.169044][ T75] ata1.00: configured for UDMA/133 [ 8.174801][ T7] scsi 0:0:0:0: Direct-Access ATA APPLE HDD HTS547 D70F PQ: 0 ANSI: 5 [ 8.185643][ T54] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 8.193876][ T54] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 8.199907][ T54] sd 0:0:0:0: [sda] Write Protect is off [ 8.205678][ T54] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.373514][ T1] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 8.379717][ T1] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 8.388308][ T1] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100 [ 8.423505][ T1] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 8.430510][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 8.439503][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.447426][ T1] usb usb1: Product: EHCI Host Controller [ 8.452979][ T1] usb usb1: Manufacturer: Linux 5.4.224-oxnas-tld-1 ehci_hcd [ 8.460200][ T1] usb usb1: SerialNumber: 40200100.ehci [ 8.466562][ T1] hub 1-0:1.0: USB hub found [ 8.471073][ T1] hub 1-0:1.0: 2 ports detected [ 8.477135][ T1] usbcore: registered new interface driver cdc_wdm [ 8.483671][ T1] usbcore: registered new interface driver usb-storage [ 8.490588][ T1] usbcore: registered new interface driver usbserial_generic [ 8.498040][ T1] usbserial: USB Serial support registered for generic [ 8.498065][ T54] sda: sda1 [ 8.505607][ T1] mousedev: PS/2 mouse device common for all mice [ 8.514490][ T1] i2c /dev entries driver [ 8.516492][ T54] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.519974][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 8.530429][ T1] usbcore: registered new interface driver usbhid [ 8.536727][ T1] usbhid: USB HID core driver [ 8.543016][ T1] NET: Registered protocol family 10 [ 8.550062][ T1] Segment Routing with IPv6 [ 8.554593][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 8.563560][ T1] NET: Registered protocol family 17 [ 8.569113][ T1] Key type dns_resolver registered [ 8.574927][ T1] registered taskstats version 1 [ 8.579699][ T1] Loading compiled-in X.509 certificates [ 8.585415][ T1] zswap: loaded using pool lzo/zbud [ 8.590986][ T1] Key type ._fscrypt registered [ 8.595758][ T1] Key type .fscrypt registered [ 8.689431][ T1] Key type big_key registered [ 8.733222][ T1] Key type encrypted registered [ 8.742535][ T1] hctosys: unable to open rtc device (rtc0) [ 8.750366][ T1] Freeing unused kernel memory: 1024K [ 8.794762][ T1] Checked W+X mappings: passed, no W+X pages found [ 8.801098][ T1] Run /init as init process Loading, please wait... starting version 232 [ 9.041797][ T114] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 9.051335][ T114] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 9.059596][ T114] random: systemd-udevd: uninitialized urandom read (16 bytes read) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: Group descriptor 0 marked uninitialized without feature set. FIXED. rootfs: 28304/122880 files (0.9% non-contiguous), 284968/1955904 blocks done. [ 23.410972][ T139] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 23.550540][ T139] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [....] Synthesizing the initial hotplug events...[ 26.512750][ T295] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 26.544186][ T315] random: udevadm: uninitialized urandom read (16 bytes read) [ 26.554780][ T315] random: udevadm: uninitialized urandom read (16 bytes read) [ 26.703685][ C1] random: crng init done [ 26.707796][ C1] random: 731 urandom warning(s) missed due to ratelimiting done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 29.378196][ T490] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [....] Checking file systems...fsck from util-linux 2.29.2 done. [ ok ] Cleaning up temporary files.... [ ok ] Loading kernel modules...done. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ [ 33.554181][ T967] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [Generic PHY] [ 33.573550][ T967] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found [ 33.581629][ T967] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 33.591101][ T967] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock [ 33.598256][ T967] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode Listening on LPF/eth0/00:30:e0:00:00:01 Sending on LPF/eth0/00:30:e0:00:00:01 Sending on Socket/fallback DHCPREQUEST of 192.168.30.12 on eth0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.30.12 on eth0 to 255.255.255.255 port 67 [ 39.834183][ T970] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 39.843310][ T970] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPREQUEST of 192.168.30.12 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 192.168.30.12 from 192.168.20.253 DHCPACK of 192.168.30.12 from 192.168.20.253 bound to 192.168.30.12 -- renewal in 37805 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1202 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1229 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. Debian GNU/Linux 10 iSharing ttyS0 iSharing login: root Password: Last login: Sun Nov 26 16:57:28 PST 2023 on ttyS0 Linux iSharing 5.4.224-oxnas-tld-1 #1.0 SMP PREEMPT Mon Nov 14 15:48:26 PST 2022 armv6l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@iSharing:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.224-oxnas-tld-1 (root@tldDebian) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1.0 SMP PREEMPT Mon Nov 14 15:48:26 PST 2022 [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Pogoplug V3 Classic [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 15 pages/cpu s30636 r8192 d22612 u61440 [ 0.000000] pcpu-alloc: s30636 r8192 d22612 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: root=LABEL=rootfs rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 240568K/262144K available (8192K kernel code, 234K rwdata, 2068K rodata, 1024K init, 258K bss, 21576K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16 [ 0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.000051] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.000069] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.000094] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.000250] GIC: PPI13 is secure or misconfigured [ 0.000307] GIC: PPI13 is secure or misconfigured [ 0.000624] Console: colour dummy device 80x30 [ 0.000698] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.050396] pid_max: default: 32768 minimum: 301 [ 0.051105] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051130] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051404] *** VALIDATE tmpfs *** [ 0.052766] *** VALIDATE proc *** [ 0.052992] *** VALIDATE cgroup1 *** [ 0.053015] *** VALIDATE cgroup2 *** [ 0.053212] CPU: Testing write buffer coherency: ok [ 0.055677] Setting up static identity map for 0x60100000 - 0x60100038 [ 0.056012] rcu: Hierarchical SRCU implementation. [ 0.057034] smp: Bringing up secondary CPUs ... [ 0.058288] GIC: PPI13 is secure or misconfigured [ 0.110661] smp: Brought up 1 node, 2 CPUs [ 0.110702] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.111897] devtmpfs: initialized [ 0.118417] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.118474] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.118673] prandom: seed boundary self test passed [ 0.122982] prandom: 100 self tests passed [ 0.123002] pinctrl core: initialized pinctrl subsystem [ 0.125109] NET: Registered protocol family 16 [ 0.126919] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130091] cpuidle: using governor ladder [ 0.130170] cpuidle: using governor menu [ 6.079173] vgaarb: loaded [ 6.080128] SCSI subsystem initialized [ 6.080770] libata version 3.00 loaded. [ 6.081113] usbcore: registered new interface driver usbfs [ 6.081203] usbcore: registered new interface driver hub [ 6.081344] usbcore: registered new device driver usb [ 6.081584] pps_core: LinuxPPS API ver. 1 registered [ 6.081602] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.081638] PTP clock support registered [ 6.083453] clocksource: Switched to clocksource oxnas_rps_clocksource_timer [ 6.083512] *** VALIDATE bpf *** [ 6.084042] *** VALIDATE ramfs *** [ 6.103982] NET: Registered protocol family 2 [ 6.104253] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 6.105354] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 6.105664] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.105728] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 6.105784] TCP: Hash tables configured (established 2048 bind 2048) [ 6.106022] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 6.106076] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 6.106385] NET: Registered protocol family 1 [ 6.107663] RPC: Registered named UNIX socket transport module. [ 6.107688] RPC: Registered udp transport module. [ 6.107704] RPC: Registered tcp transport module. [ 6.107719] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 6.107742] PCI: CLS 0 bytes, default 32 [ 6.108211] Unpacking initramfs... [ 6.844638] Freeing initrd memory: 6348K [ 6.846082] Initialise system trusted keyrings [ 6.846205] Key type blacklist registered [ 6.846663] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 6.858375] zbud: loaded [ 6.864645] NFS: Registering the id_resolver key type [ 6.864716] Key type id_resolver registered [ 6.864732] Key type id_legacy registered [ 6.864765] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.864780] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 6.864793] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.866181] fuse: init (API version 7.31) [ 6.866455] *** VALIDATE fuse *** [ 6.866483] *** VALIDATE fuse *** [ 6.867358] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.867737] orangefs_init: module version upstream loaded [ 6.915074] Key type asymmetric registered [ 6.915107] Asymmetric key parser 'x509' registered [ 6.915202] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 6.922316] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 6.923988] printk: console [ttyS0] disabled [ 6.924162] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A [ 7.564981] printk: console [ttyS0] enabled [ 7.585149] loop: module loaded [ 7.591370] scsi host0: sata_oxnas [ 7.596259] ata1: SATA max UDMA/133 irq 57 [ 7.601159] sata_oxnas: resetting SATA core [ 7.663800] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it [ 7.673213] ONFI parameter recovery failed, aborting [ 7.678924] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 7.685980] nand: Hynix NAND 256MiB 3,3V 8-bit [ 7.691100] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.699376] Scanning device for bad blocks [ 7.868833] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller [ 7.877437] Creating 2 MTD partitions on "41000000.nand-controller": [ 7.884554] 0x000000000000-0x000000e00000 : "boot" [ 7.891077] 0x000000e00000-0x000008000000 : "data" [ 7.898631] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found [ 7.905500] oxnas-dwmac 40400000.ethernet: PTP uses main clock [ 7.912012] oxnas-dwmac 40400000.ethernet: no reset control found [ 7.983964] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35 [ 7.991605] oxnas-dwmac 40400000.ethernet: DWMAC1000 [ 7.997391] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported [ 8.005399] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported [ 8.013368] oxnas-dwmac 40400000.ethernet: COE Type 2 [ 8.019120] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported [ 8.026688] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported [ 8.033658] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors [ 8.041105] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors [ 8.048414] oxnas-dwmac 40400000.ethernet: Ring mode enabled [ 8.054791] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 8.108730] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 8.118947] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL) [ 8.123517] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 8.130227] PPP generic driver version 2.4.2 [ 8.141352] ata1.00: ATA-8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133 [ 8.141386] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.149242] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 8.163840] ehci-pci: EHCI PCI platform driver [ 8.169044] ata1.00: configured for UDMA/133 [ 8.174801] scsi 0:0:0:0: Direct-Access ATA APPLE HDD HTS547 D70F PQ: 0 ANSI: 5 [ 8.185643] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 8.193876] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 8.199907] sd 0:0:0:0: [sda] Write Protect is off [ 8.205450] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 8.205678] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.373514] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 8.379717] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 8.388308] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100 [ 8.423505] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 8.430510] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 8.439503] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.447426] usb usb1: Product: EHCI Host Controller [ 8.452979] usb usb1: Manufacturer: Linux 5.4.224-oxnas-tld-1 ehci_hcd [ 8.460200] usb usb1: SerialNumber: 40200100.ehci [ 8.466562] hub 1-0:1.0: USB hub found [ 8.471073] hub 1-0:1.0: 2 ports detected [ 8.477135] usbcore: registered new interface driver cdc_wdm [ 8.483671] usbcore: registered new interface driver usb-storage [ 8.490588] usbcore: registered new interface driver usbserial_generic [ 8.498040] usbserial: USB Serial support registered for generic [ 8.498065] sda: sda1 [ 8.505607] mousedev: PS/2 mouse device common for all mice [ 8.514490] i2c /dev entries driver [ 8.516492] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.519974] hidraw: raw HID events driver (C) Jiri Kosina [ 8.530429] usbcore: registered new interface driver usbhid [ 8.536727] usbhid: USB HID core driver [ 8.543016] NET: Registered protocol family 10 [ 8.550062] Segment Routing with IPv6 [ 8.554593] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 8.563560] NET: Registered protocol family 17 [ 8.569113] Key type dns_resolver registered [ 8.574927] registered taskstats version 1 [ 8.579699] Loading compiled-in X.509 certificates [ 8.585415] zswap: loaded using pool lzo/zbud [ 8.590986] Key type ._fscrypt registered [ 8.595758] Key type .fscrypt registered [ 8.689431] Key type big_key registered [ 8.733222] Key type encrypted registered [ 8.742535] hctosys: unable to open rtc device (rtc0) [ 8.750366] Freeing unused kernel memory: 1024K [ 8.794762] Checked W+X mappings: passed, no W+X pages found [ 8.801098] Run /init as init process [ 9.041797] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 9.051335] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 9.059596] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 23.410972] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 23.550540] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 26.512750] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 26.544186] random: udevadm: uninitialized urandom read (16 bytes read) [ 26.554780] random: udevadm: uninitialized urandom read (16 bytes read) [ 26.703685] random: crng init done [ 26.707796] random: 731 urandom warning(s) missed due to ratelimiting [ 29.378196] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 33.554181] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [Generic PHY] [ 33.573550] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found [ 33.581629] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 33.591101] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock [ 33.598256] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode [ 39.834183] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 39.843310] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready root@iSharing:~#
root@iSharing:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.224-oxnas-tld-1 (root@tldDebian) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1.0 SMP PREEMPT Mon Nov 14 15:48:26 PST 2022 [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Pogoplug V3 Classic [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 15 pages/cpu s30636 r8192 d22612 u61440 [ 0.000000] pcpu-alloc: s30636 r8192 d22612 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: root=LABEL=rootfs rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 240568K/262144K available (8192K kernel code, 234K rwdata, 2068K rodata, 1024K init, 258K bss, 21576K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16 [ 0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.000048] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.000066] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.000094] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.000258] GIC: PPI13 is secure or misconfigured [ 0.000314] GIC: PPI13 is secure or misconfigured [ 0.000632] Console: colour dummy device 80x30 [ 0.000706] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.050401] pid_max: default: 32768 minimum: 301 [ 0.051110] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051138] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051407] *** VALIDATE tmpfs *** [ 0.052725] *** VALIDATE proc *** [ 0.052938] *** VALIDATE cgroup1 *** [ 0.052961] *** VALIDATE cgroup2 *** [ 0.053158] CPU: Testing write buffer coherency: ok [ 0.055644] Setting up static identity map for 0x60100000 - 0x60100038 [ 0.055989] rcu: Hierarchical SRCU implementation. [ 0.057021] smp: Bringing up secondary CPUs ... [ 0.058288] GIC: PPI13 is secure or misconfigured [ 0.110668] smp: Brought up 1 node, 2 CPUs [ 0.110707] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.111920] devtmpfs: initialized [ 0.118714] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.118773] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.118922] prandom: seed boundary self test passed [ 0.123225] prandom: 100 self tests passed [ 0.123248] pinctrl core: initialized pinctrl subsystem [ 0.125432] NET: Registered protocol family 16 [ 0.127244] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130414] cpuidle: using governor ladder [ 0.130490] cpuidle: using governor menu [ 6.079838] vgaarb: loaded [ 6.080885] SCSI subsystem initialized [ 6.081438] libata version 3.00 loaded. [ 6.081850] usbcore: registered new interface driver usbfs [ 6.081953] usbcore: registered new interface driver hub [ 6.082037] usbcore: registered new device driver usb [ 6.082309] pps_core: LinuxPPS API ver. 1 registered [ 6.082324] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.082357] PTP clock support registered [ 6.084264] clocksource: Switched to clocksource oxnas_rps_clocksource_timer [ 6.084323] *** VALIDATE bpf *** [ 6.084848] *** VALIDATE ramfs *** [ 6.104911] NET: Registered protocol family 2 [ 6.105200] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 6.106319] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 6.106636] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.106700] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 6.106757] TCP: Hash tables configured (established 2048 bind 2048) [ 6.106997] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 6.107054] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 6.107368] NET: Registered protocol family 1 [ 6.108623] RPC: Registered named UNIX socket transport module. [ 6.108648] RPC: Registered udp transport module. [ 6.108664] RPC: Registered tcp transport module. [ 6.108679] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 6.108702] PCI: CLS 0 bytes, default 32 [ 6.109160] Unpacking initramfs... [ 6.843655] Freeing initrd memory: 6348K [ 6.845227] Initialise system trusted keyrings [ 6.845460] Key type blacklist registered [ 6.845877] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 6.858291] zbud: loaded [ 6.864289] NFS: Registering the id_resolver key type [ 6.864363] Key type id_resolver registered [ 6.864378] Key type id_legacy registered [ 6.864414] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.864430] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 6.864445] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.865914] fuse: init (API version 7.31) [ 6.866204] *** VALIDATE fuse *** [ 6.866232] *** VALIDATE fuse *** [ 6.867184] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.867566] orangefs_init: module version upstream loaded [ 6.916229] Key type asymmetric registered [ 6.916262] Asymmetric key parser 'x509' registered [ 6.916354] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 6.923461] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 6.925020] printk: console [ttyS0] disabled [ 6.925191] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A [ 7.566236] printk: console [ttyS0] enabled [ 7.586432] loop: module loaded [ 7.592619] scsi host0: sata_oxnas [ 7.597447] ata1: SATA max UDMA/133 irq 57 [ 7.602342] sata_oxnas: resetting SATA core [ 7.664611] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it [ 7.674024] ONFI parameter recovery failed, aborting [ 7.679736] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 7.686791] nand: Hynix NAND 256MiB 3,3V 8-bit [ 7.691909] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.700185] Scanning device for bad blocks [ 7.869729] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller [ 7.878333] Creating 2 MTD partitions on "41000000.nand-controller": [ 7.885450] 0x000000000000-0x000000e00000 : "boot" [ 7.891888] 0x000000e00000-0x000008000000 : "data" [ 7.899509] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found [ 7.906380] oxnas-dwmac 40400000.ethernet: PTP uses main clock [ 7.912893] oxnas-dwmac 40400000.ethernet: no reset control found [ 7.984770] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35 [ 7.992412] oxnas-dwmac 40400000.ethernet: DWMAC1000 [ 7.998195] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported [ 8.006202] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported [ 8.014172] oxnas-dwmac 40400000.ethernet: COE Type 2 [ 8.019927] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported [ 8.027491] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported [ 8.034457] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors [ 8.041907] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors [ 8.049213] oxnas-dwmac 40400000.ethernet: Ring mode enabled [ 8.055592] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 8.110172] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 8.120381] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL) [ 8.124336] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 8.131576] PPP generic driver version 2.4.2 [ 8.142771] ata1.00: ATA-8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133 [ 8.142801] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.150663] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 8.157923] ehci-pci: EHCI PCI platform driver [ 8.171484] ata1.00: configured for UDMA/133 [ 8.177190] scsi 0:0:0:0: Direct-Access ATA APPLE HDD HTS547 D70F PQ: 0 ANSI: 5 [ 8.187947] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 8.196221] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 8.202250] sd 0:0:0:0: [sda] Write Protect is off [ 8.207784] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 8.208010] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.364328] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 8.370531] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 8.379118] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100 [ 8.414312] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 8.421327] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 8.430312] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.438231] usb usb1: Product: EHCI Host Controller [ 8.443781] usb usb1: Manufacturer: Linux 5.4.224-oxnas-tld-1 ehci_hcd [ 8.451000] usb usb1: SerialNumber: 40200100.ehci [ 8.457313] hub 1-0:1.0: USB hub found [ 8.461818] hub 1-0:1.0: 2 ports detected [ 8.467896] usbcore: registered new interface driver cdc_wdm [ 8.474419] usbcore: registered new interface driver usb-storage [ 8.481333] usbcore: registered new interface driver usbserial_generic [ 8.488678] usbserial: USB Serial support registered for generic [ 8.495626] sda: sda1 [ 8.496215] mousedev: PS/2 mouse device common for all mice [ 8.505226] i2c /dev entries driver [ 8.507376] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.510850] hidraw: raw HID events driver (C) Jiri Kosina [ 8.521111] usbcore: registered new interface driver usbhid [ 8.527398] usbhid: USB HID core driver [ 8.533770] NET: Registered protocol family 10 [ 8.540792] Segment Routing with IPv6 [ 8.545328] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 8.554360] NET: Registered protocol family 17 [ 8.559925] Key type dns_resolver registered [ 8.565803] registered taskstats version 1 [ 8.570580] Loading compiled-in X.509 certificates [ 8.576302] zswap: loaded using pool lzo/zbud [ 8.581888] Key type ._fscrypt registered [ 8.586659] Key type .fscrypt registered [ 8.680258] Key type big_key registered [ 8.724387] Key type encrypted registered [ 8.733401] hctosys: unable to open rtc device (rtc0) [ 8.741230] Freeing unused kernel memory: 1024K [ 8.775616] Checked W+X mappings: passed, no W+X pages found [ 8.781949] Run /init as init process [ 9.021895] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 9.031370] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 9.039700] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 10.483773] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 10.521080] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 13.439918] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 13.494722] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 13.502786] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 14.444456] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 14.446041] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 14.452761] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 16.273216] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 19.704829] random: dd: uninitialized urandom read (32 bytes read) [ 20.415662] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [Generic PHY] [ 20.434347] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found [ 20.442424] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 20.455585] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock [ 20.462638] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode [ 26.714992] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 26.724119] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 41.570183] random: crng init done [ 41.574325] random: 1452 urandom warning(s) missed due to ratelimiting
root@iSharing:/# apt update Hit:1 http://security.debian.org buster/updates InRelease Hit:2 http://ftp.us.debian.org/debian buster InRelease Hit:3 http://deb.debian.org/debian buster-updates InRelease Reading package lists... Done E: Release file for http://security.debian.org/dists/buster/updates/InRelease is expired (invalid since 1284d 8h 39min 37s). Updates for this repository will not be applied. E: Release file for http://http.debian.net/debian/dists/buster-updates/InRelease is expired (invalid since 1284d 1h 30min 11s). Updates for this repository will not be applied . root@iSharing:/# apt install dirmngr --install-recommends Reading package lists... Done Building dependency tree Reading state information... Done The following additional packages will be installed: gnupg gnupg-agent gnupg-l10n gnupg-utils gpg gpg-agent gpg-wks-client gpg-wks-server gpgconf gpgsm libgnutls30 libidn2-0 libunistring2 Suggested packages: dbus-user-session libpam-systemd pinentry-gnome3 tor parcimonie xloadimage scdaemon gnutls-bin The following NEW packages will be installed: dirmngr gnupg-l10n gnupg-utils gpg gpg-agent gpg-wks-client gpg-wks-server gpgconf gpgsm libunistring2 The following packages will be upgraded: gnupg gnupg-agent libgnutls30 libidn2-0 4 upgraded, 10 newly installed, 0 to remove and 55 not upgraded. Need to get 8403 kB of archives. After this operation, 12.6 MB of additional disk space will be used. Do you want to continue? [Y/n] Y Err:1 http://ftp.us.debian.org/debian buster/main armel gnupg-l10n all 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:2 http://ftp.us.debian.org/debian buster/main armel gnupg all 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:3 http://ftp.us.debian.org/debian buster/main armel gnupg-agent all 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:4 http://ftp.us.debian.org/debian buster/main armel gpgconf armel 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:5 http://ftp.us.debian.org/debian buster/main armel gpg-agent armel 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:6 http://ftp.us.debian.org/debian buster/main armel gnupg-utils armel 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:7 http://ftp.us.debian.org/debian buster/main armel gpg armel 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:8 http://ftp.us.debian.org/debian buster/main armel gpg-wks-client armel 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:9 http://ftp.us.debian.org/debian buster/main armel gpg-wks-server armel 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:10 http://ftp.us.debian.org/debian buster/main armel gpgsm armel 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Get:11 http://ftp.us.debian.org/debian buster/main armel libunistring2 armel 0.9.10-1 [354 kB] Get:12 http://ftp.us.debian.org/debian buster/main armel libidn2-0 armel 2.0.5-1+deb10u1 [73.9 kB] Err:13 http://ftp.us.debian.org/debian buster/main armel libgnutls30 armel 3.6.7-4+deb10u3 404 Not Found [IP: 208.80.154.139 80] Err:14 http://ftp.us.debian.org/debian buster/main armel dirmngr armel 2.2.12-1+deb10u1 404 Not Found [IP: 208.80.154.139 80] Err:13 http://security.debian.org buster/updates/main armel libgnutls30 armel 3.6.7-4+deb10u3 404 Not Found [IP: 208.80.154.139 80] Fetched 428 kB in 2s (169 kB/s) E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gnupg-l10n_2.2.12-1+deb10u1_all.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gnupg_2.2.12-1+deb10u1_all.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gnupg-agent_2.2.12-1+deb10u1_all.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gpgconf_2.2.12-1+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gpg-agent_2.2.12-1+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gnupg-utils_2.2.12-1+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gpg_2.2.12-1+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gpg-wks-client_2.2.12-1+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gpg-wks-server_2.2.12-1+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/gpgsm_2.2.12-1+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://security.debian.org/pool/updates/main/g/gnutls28/libgnutls30_3.6.7-4+deb10u3_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Failed to fetch http://ftp.us.debian.org/debian/pool/main/g/gnupg2/dirmngr_2.2.12-1+deb10u1_armel.deb 404 Not Found [IP: 208.80.154.139 80] E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? root@iSharing:/#
root@iSharing:/etc/apt# vi sources.list root@iSharing:/etc/apt# apt update Hit:1 http://opensource.nchc.org.tw/debian buster InRelease Get:2 http://opensource.nchc.org.tw/debian buster-updates InRelease [56.6 kB] Hit:3 http://security.debian.org/debian-security oldstable-security InRelease Get:4 http://opensource.nchc.org.tw/debian buster-updates/main Sources [4616 B] Get:5 http://opensource.nchc.org.tw/debian buster-updates/main armel Packages [8792 B] Get:6 http://opensource.nchc.org.tw/debian buster-updates/main Translation-en [6915 B] Fetched 76.9 kB in 4s (17.3 kB/s) Reading package lists... Done Building dependency tree Reading state information... Done 111 packages can be upgraded. Run 'apt list --upgradable' to see them. root@iSharing:/etc/apt# cat sources.list deb http://opensource.nchc.org.tw/debian buster main deb-src http://opensource.nchc.org.tw/debian buster main deb http://security.debian.org/debian-security oldstable-security main contrib non-free deb-src http://security.debian.org/debian-security oldstable-security main contrib non-free deb http://opensource.nchc.org.tw/debian buster-updates main contrib deb-src http://opensource.nchc.org.tw/debian buster-updates main contrib
/usr/bin/mandb: can't chmod /var/cache/man/sv/CACHEDIR.TAG: Operation not permit /usr/bin/mandb: can't remove /var/cache/man/sv/CACHEDIR.TAG: Permission denied /usr/bin/mandb: fopen /var/cache/man/sv/28711: Permission denied chown man:root /var/cache/man -R chmod g+s /var/cache/man -R
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 27, 2023 01:18AM |
Admin Registered: 13 years ago Posts: 18,821 |
Hit:1 http://opensource.nchc.org.tw/debian buster InRelease Get:2 http://opensource.nchc.org.tw/debian buster-updates InRelease [56.6 kB] Hit:3 http://security.debian.org/debian-security oldstable-security InRelease Get:4 http://opensource.nchc.org.tw/debian buster-updates/main Sources [4616 B] Get:5 http://opensource.nchc.org.tw/debian buster-updates/main armel Packages [8792 B] Get:6 http://opensource.nchc.org.tw/debian buster-updates/main Translation-en [6915 B]
cat /etc/apt/sources.list
[ 20.415662] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [Generic PHY] [ 20.434347] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found [ 20.442424] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 20.455585] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock [ 20.462638] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode [ 26.714992] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 26.724119] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ethtool eth0
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 27, 2023 02:06AM |
Registered: 9 months ago Posts: 82 |
nand-controller@41000000 {
compatible = "oxsemi,ox820-nand";
reg = <0x41000000 0x100000>;
clocks = <0x05 0x09>;
resets = <0x06 0x0f>;
#address-cells = <0x01>;
#size-cells = <0x00>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x07>;
nand@0 {
reg = <0x00>;
#address-cells = <0x01>;
#size-cells = <0x01>;
nand-ecc-mode = "soft";
nand-ecc-algo = "hamming";
partition@0 {
label = "boot";
reg = <0x00 0xe00000>;
read-only;
};
partition@e00000 {
label = "data";
reg = <0xe00000 0x7200000>;
};
};
};
&nandc {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand>;
nand@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <1>;
nand-ecc-mode = "soft";
nand-ecc-algo = "hamming";
partition@0 {
label = "boot";
reg = <0x0 0x26c0000>;
};
partition@26c0000 {
label = "ubi";
reg = <0x26c0000 0xd940000>;
};
};
};
$ cat /proc/mtd
dev: size erasesize name
mtd0: 10000000 00020000 "NAND 256MiB 3,3V 8-bit"
mtd1: 026c0000 00020000 "Boot partition"
mtd2: 0d940000 00020000 "Data Partition"
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:rootfs", error -19
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00 262144 mtdblock0 (driver?)
1f01 39680 mtdblock1 (driver?)
1f02 222464 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Environment size: 1929/16380 bytes
OX820 # run ide_set_bootargs; run dt_ide_boot
5589656 bytes read in 1963 ms (2.7 MiB/s)
6497808 bytes read in 2223 ms (2.8 MiB/s)
9945 bytes read in 77 ms (126 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-5.4.224-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5589592 Bytes = 5.3 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-5.4.224-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6497744 Bytes = 6.2 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f7f6000, end 6fe285d0 ... OK
Loading Device Tree to 6f7f0000, end 6f7f56d8 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.4.224-oxnas-tld-1 (root@tldDebian) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1.0 SMP PREEMPT Mon Nov 14 15:48:26 PST 2022
[ 0.000000][ T0] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Akitio MyCloud
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] percpu: Embedded 15 pages/cpu s30636 r8192 d22612 u61440
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000][ T0] Kernel command line: root=LABEL=rootfs rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes
[ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 240564K/262144K available (8192K kernel code, 234K rwdata, 2068K rodata, 1024K init, 258K bss, 21580K reserved, 0K cma-reserved)
[ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16
[ 0.000017][ T0] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.000046][ T0] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000064][ T0] timer_oxnas_rps: Registered clocksource rate 390625Hz
[ 0.000089][ T0] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[ 0.000243][ T0] GIC: PPI13 is secure or misconfigured
[ 0.000296][ T0] GIC: PPI13 is secure or misconfigured
[ 0.000622][ T0] Console: colour dummy device 80x30
[ 0.000698][ T0] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.050385][ T0] pid_max: default: 32768 minimum: 301
[ 0.051123][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.051151][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.051422][ T0] *** VALIDATE tmpfs ***
[ 0.052769][ T0] *** VALIDATE proc ***
[ 0.052992][ T0] *** VALIDATE cgroup1 ***
[ 0.053015][ T0] *** VALIDATE cgroup2 ***
[ 0.053214][ T0] CPU: Testing write buffer coherency: ok
[ 0.055715][ T1] Setting up static identity map for 0x60100000 - 0x60100038
[ 0.056048][ T1] rcu: Hierarchical SRCU implementation.
[ 0.057067][ T1] smp: Bringing up secondary CPUs ...
[ 0.058357][ T0] GIC: PPI13 is secure or misconfigured
[ 0.110650][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.110689][ T1] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.111895][ T1] devtmpfs: initialized
[ 0.118991][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.119045][ T1] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.119191][ T1] prandom: seed boundary self test passed
[ 0.123491][ T1] prandom: 100 self tests passed
[ 0.123512][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.125693][ T1] NET: Registered protocol family 16
[ 0.127585][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.131041][ T1] cpuidle: using governor ladder
[ 0.131125][ T1] cpuidle: using governor menu
[ 6.082240][ T1] vgaarb: loaded
[ 6.083184][ T1] SCSI subsystem initialized
[ 6.084003][ T1] usbcore: registered new interface driver usbfs
[ 6.084103][ T1] usbcore: registered new interface driver hub
[ 6.084185][ T1] usbcore: registered new device driver usb
[ 6.084436][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 6.084451][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 6.084487][ T1] PTP clock support registered
[ 6.086320][ T1] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[ 6.086379][ T1] *** VALIDATE bpf ***
[ 6.086914][ T1] *** VALIDATE ramfs ***
[ 6.106585][ T1] NET: Registered protocol family 2
[ 6.106864][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 6.107970][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 6.108285][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 6.108352][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 6.108410][ T1] TCP: Hash tables configured (established 2048 bind 2048)
[ 6.108643][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 6.108697][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 6.109009][ T1] NET: Registered protocol family 1
[ 6.110279][ T1] RPC: Registered named UNIX socket transport module.
[ 6.110305][ T1] RPC: Registered udp transport module.
[ 6.110320][ T1] RPC: Registered tcp transport module.
[ 6.110333][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 6.110359][ T1] PCI: CLS 0 bytes, default 32
[ 6.110824][ T1] Unpacking initramfs...
[ 6.845813][ T1] Freeing initrd memory: 6348K
[ 6.847393][ T1] Initialise system trusted keyrings
[ 6.847536][ T1] Key type blacklist registered
[ 6.847976][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 6.860986][ T1] zbud: loaded
[ 6.867130][ T1] NFS: Registering the id_resolver key type
[ 6.867246][ T1] Key type id_resolver registered
[ 6.867261][ T1] Key type id_legacy registered
[ 6.867294][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 6.867310][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 6.867325][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 6.868843][ T1] fuse: init (API version 7.31)
[ 6.869127][ T1] *** VALIDATE fuse ***
[ 6.869155][ T1] *** VALIDATE fuse ***
[ 6.870131][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 6.870512][ T1] orangefs_init: module version upstream loaded
[ 6.921745][ T1] Key type asymmetric registered
[ 6.921781][ T1] Asymmetric key parser 'x509' registered
[ 6.921871][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 6.929543][ T1] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 6.931013][ T1] printk: console [ttyS0] disabled
[ 6.931182][ T1] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[ 7.571735][ T1] printk: console [ttyS0] enabled
[ 7.592220][ T1] loop: module loaded
[ 7.599119][ T1] scsi host0: sata_oxnas
[ 7.604500][ T1] scsi host1: sata_oxnas
[ 7.609141][ T1] ata1: SATA max UDMA/133 irq 57
[ 7.613923][ T1] ata2: SATA max UDMA/133 irq 57
[ 7.618880][ T75] sata_oxnas: resetting SATA core
[ 7.686663][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 7.696074][ T1] ONFI parameter recovery failed, aborting
[ 7.701785][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[ 7.708840][ T1] nand: Hynix NAND 256MiB 3,3V 8-bit
[ 7.713960][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 7.722240][ T1] Scanning device for bad blocks
[ 7.892416][ T1] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller
[ 7.901022][ T1] Creating 2 MTD partitions on "41000000.nand-controller":
[ 7.908142][ T1] 0x000000000000-0x0000026c0000 : "boot"
[ 7.914698][ T1] 0x0000026c0000-0x000010000000 : "ubi"
[ 7.922690][ T1] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found
[ 7.929569][ T1] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[ 7.936076][ T1] oxnas-dwmac 40400000.ethernet: no reset control found
[ 8.006786][ T1] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35
[ 8.014428][ T1] oxnas-dwmac 40400000.ethernet: DWMAC1000
[ 8.020216][ T1] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[ 8.028224][ T1] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[ 8.036193][ T1] oxnas-dwmac 40400000.ethernet: COE Type 2
[ 8.041943][ T1] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[ 8.049510][ T1] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[ 8.056481][ T1] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[ 8.063933][ T1] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[ 8.071242][ T1] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[ 8.077685][ T1] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 8.126446][ T75] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 8.131394][ T1] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 8.143554][ T1] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[ 8.153809][ T75] ata1.00: ATA-8: APPLE HDD HTS547550A9E384, JE3AD70F, max UDMA/133
[ 8.154785][ T1] PPP generic driver version 2.4.2
[ 8.161745][ T75] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 8.174141][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.181457][ T1] ehci-pci: EHCI PCI platform driver
[ 8.186897][ T75] ata1.00: configured for UDMA/133
[ 8.192514][ T7] scsi 0:0:0:0: Direct-Access ATA APPLE HDD HTS547 D70F PQ: 0 ANSI: 5
[ 8.203010][ T79] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 8.211558][ T79] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 8.217753][ T77] sata_oxnas: resetting SATA core
[ 8.217856][ T79] sd 0:0:0:0: [sda] Write Protect is off
[ 8.228408][ T79] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.238228][ T75] sata_oxnas: resetting SATA core
[ 8.396385][ T1] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 8.402595][ T1] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 8.411353][ T1] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[ 8.446438][ T1] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 8.453465][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 8.462446][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.470425][ T1] usb usb1: Product: EHCI Host Controller
[ 8.475978][ T1] usb usb1: Manufacturer: Linux 5.4.224-oxnas-tld-1 ehci_hcd
[ 8.483202][ T1] usb usb1: SerialNumber: 40200100.ehci
[ 8.489656][ T1] hub 1-0:1.0: USB hub found
[ 8.494164][ T1] hub 1-0:1.0: 2 ports detected
[ 8.500011][ T1] usbcore: registered new interface driver cdc_wdm
[ 8.506685][ T1] usbcore: registered new interface driver usb-storage
[ 8.513505][ T1] usbcore: registered new interface driver usbserial_generic
[ 8.520791][ T1] usbserial: USB Serial support registered for generic
[ 8.528327][ T1] mousedev: PS/2 mouse device common for all mice
[ 8.534702][ T1] i2c /dev entries driver
[ 8.540362][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 8.546764][ T1] usbcore: registered new interface driver usbhid
[ 8.553003][ T1] usbhid: USB HID core driver
[ 8.559552][ T1] NET: Registered protocol family 10
[ 8.566671][ T1] Segment Routing with IPv6
[ 8.571171][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 8.580195][ T1] NET: Registered protocol family 17
[ 8.585807][ T1] Key type dns_resolver registered
[ 8.591761][ T1] registered taskstats version 1
[ 8.596625][ T1] Loading compiled-in X.509 certificates
[ 8.602278][ T1] zswap: loaded using pool lzo/zbud
[ 8.607971][ T1] Key type ._fscrypt registered
[ 8.612664][ T1] Key type .fscrypt registered
[ 8.707271][ T1] Key type big_key registered
[ 8.751769][ T1] Key type encrypted registered
[ 8.898257][ T77] ata2: SATA link down (SStatus 0 SControl 300)
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 27, 2023 02:18AM |
Registered: 9 months ago Posts: 82 |
root@iSharing:/etc/apt# cat sources.list deb http://opensource.nchc.org.tw/debian buster main deb-src http://opensource.nchc.org.tw/debian buster main deb http://security.debian.org/debian-security oldstable-security main contrib non-free deb-src http://security.debian.org/debian-security oldstable-security main contrib non-free deb http://opensource.nchc.org.tw/debian buster-updates main contrib deb-src http://opensource.nchc.org.tw/debian buster-updates main contrib
root@iSharing:~# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: ug Wake-on: d Current message level: 0x0000003f (63) drv probe link timer ifdown ifup Link detected: yes
Re: Help! Akitio mycloudmini using stock kernel but missing system setting files November 27, 2023 02:45AM |
Registered: 9 months ago Posts: 82 |
root@iSharing:~# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: ug Wake-on: d Current message level: 0x0000003f (63) drv probe link timer ifdown ifup Link detected: yes
------------------------------------------------------------
Client connecting to 192.168.30.12, TCP port 5001
TCP window size: 16.0 MByte (default)
------------------------------------------------------------
[ 3] local 10.0.3.2 port 32850 connected with 192.168.30.12 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.1 sec 448 MBytes 371 Mbits/sec