So I am able to connect no problem with a vnc viewer and this setup 10.107.5.233:5901. RDP login still doesn't work. How can I enable a gui network manager?by brickman7713@gmail.com - Debian
This is the output of those two commands, and I tried what Navi did but still got the same results (after installing xrdp) root@debian:~# ps -deaf | grep rdp root 1919 1 0 19:01 ? 00:00:00 /usr/sbin/xrdp-sesman xrdp 1925 1 0 19:01 ? 00:00:00 /usr/sbin/xrdp root 2312 2020 1 19:19 pts/0 00:00:00 grep rdp root@debian:~# ps -deaf | grep vnc rootby brickman7713@gmail.com - Debian
I can ssh into the box, and connect via rdc but when I go to login in under rdc the login box goes away and eventually a box pops up in the top left with an errorby brickman7713@gmail.com - Debian
Got it thanks! I am now running debian on my pogoplugby brickman7713@gmail.com - uBoot
Hello, so I followed this guide and now I can rdc into pogoplug but I can't seem to login. What is the ip box under sessman-xvnc for? Thanksby brickman7713@gmail.com - Debian
Ok so I think I got the usb drive all set, how do I get the pogoplug to boot from it now? I don't see that in the instructionsby brickman7713@gmail.com - uBoot
I am stuck on the "apt-get remove flash-kernel" command, I get an error "unable to locate package flash kernel"by brickman7713@gmail.com - uBoot
Ok thanks again, so I extract the tar too the root of the flash drive then follow the instructions on the link you sent me before.by brickman7713@gmail.com - uBoot
So I read through that and I'm still a little confused. Do I need to install debian on a USB myself before following that guide?by brickman7713@gmail.com - uBoot
Cool hopefully I’ll get to it in the next couple days, thanks for all the help.by brickman7713@gmail.com - uBoot
Ok thank you, so Debian will rub off from a flash drive correct?by brickman7713@gmail.com - uBoot
I guess not since I can't find the /boot directoryby brickman7713@gmail.com - uBoot
Ok enbled SSH with this method https://www.reddit.com/r/pogoplug/comments/5m9sd6/pogoplug_is_dead/. Now I can follow the debian guide?by brickman7713@gmail.com - uBoot
Ok thanks, can you tell me why I get a red light then and I can’t connect to it through the network at all? Or how to enable ssh via serialby brickman7713@gmail.com - uBoot
This is the printenv output. CE>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes CASset=min MALLOC_len=1 ethprime=egiga0 load_nand=nboot 0x800000 0 0x200000 load_nand2=nboot 0x800000 0 0x500000 boot=bootm 0x800000 boot_nand=run load_nand boot || run load_nand2 boot ethmtu=1500 usb0Mode=host nandEcc=1bit ethact=egiga0 ethaddby brickman7713@gmail.com - uBoot
I will post the printenv output soon, but how do I copy the complete serial output? I can't scroll up on the terminal on ubuntuby brickman7713@gmail.com - uBoot
I assume it is stock but it has never booted since I bought it. I don't really care what I do with it as long as I fix it, I will probably install debian eventually, but I don't care yet. Thanks for the responseby brickman7713@gmail.com - uBoot
Hello, I am new to pogoplug and the first one I bought has never worked properly. I finally figured out I can use a serial connection to it to see what the problem is. But I can't seem to find any answer to uboot not working. I've attached the end of the serial output below, any help would be awesome.Thanks Quote[ 1.450000] UBI: background thread "ubi_bgt0d" started, PID 45by brickman7713@gmail.com - uBoot