Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread
Posted by JeffS
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 11:57PM |
Registered: 9 years ago Posts: 1,516 |
I swear the XFCE Mint is much less flaky than Cinnamon, but the ThinClient is 32-bit and that was the only 32-bit on hand.
Let me get three variables knocked out for tomorrow, and try this again. It's rare 5 spare computers can't help, but I'll run personal errands and get a tight ship running tomorrow afternoon hopefully.
=========
-= Cloud 9 =-
Let me get three variables knocked out for tomorrow, and try this again. It's rare 5 spare computers can't help, but I'll run personal errands and get a tight ship running tomorrow afternoon hopefully.
=========
-= Cloud 9 =-
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 12:02AM |
Admin Registered: 13 years ago Posts: 18,898 |
OK, I've just tried it.
In Mint, plugged in a brand new 16GB Ultra Fit. And use the menu
Accessories--> USB Stick Formatter.
Formatted it as Ext4 and it came out one partition for the whole disk.
So the question is why does your stick have 2 partitions after you've formatted it?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
In Mint, plugged in a brand new 16GB Ultra Fit. And use the menu
Accessories--> USB Stick Formatter.
Formatted it as Ext4 and it came out one partition for the whole disk.
So the question is why does your stick have 2 partitions after you've formatted it?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 12:22AM |
Registered: 7 years ago Posts: 49 |
Hey Joey, bodhi,
Just wanted to pop in and check things out, wow some awesome stuff going on here guys. I've got a new v3 pro still in the box. It's just waiting for me to get some free time!
Back to work (wage slave) and nursing a cold = lots of nap time for me lately. I hope to regain more energy moving forward so I can get involved in this stuff again.
--------------------------------------------------------------
Blog: www.jeffstory.org
Just wanted to pop in and check things out, wow some awesome stuff going on here guys. I've got a new v3 pro still in the box. It's just waiting for me to get some free time!
Back to work (wage slave) and nursing a cold = lots of nap time for me lately. I hope to regain more energy moving forward so I can get involved in this stuff again.
--------------------------------------------------------------
Blog: www.jeffstory.org
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 12:38AM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> So the question is why does your stick have 2 part
> itions after you've formatted it?
Almost certainly pilot error here but I'll re-do everything on a better machine tomorrow, with Mint XFCE 64-bit.
All I know is, G-Parted formatted Ext4 but wouldn't let me label it. So I labeled it afterwards and apparantly Partition Magic is running amok.
JeffS Wrote:
-------------------------------------------------------
> Hey Joey, bodhi,
> .. nursing a cold = lot
> s of nap time for me lately. I hope to regain more
> energy moving forward so I can get involved in thi
> s stuff again.
I got over that last month, and right now whole towns nearby have their schools closed this week because of three illnesses at the same time, and that doesn't include all the colds and flu from Spring Break and all the college students bringing sickness home from all corners of the world. Just splurge on orange juice and nap for days. Vape-O-rub on my nose helped a lot and tons of kleenex, lots of eucalyptus cough drops. Just the lowest, meanest, ugliest cold I had in ages.
=========
-= Cloud 9 =-
-------------------------------------------------------
> So the question is why does your stick have 2 part
> itions after you've formatted it?
Almost certainly pilot error here but I'll re-do everything on a better machine tomorrow, with Mint XFCE 64-bit.
All I know is, G-Parted formatted Ext4 but wouldn't let me label it. So I labeled it afterwards and apparantly Partition Magic is running amok.
JeffS Wrote:
-------------------------------------------------------
> Hey Joey, bodhi,
> .. nursing a cold = lot
> s of nap time for me lately. I hope to regain more
> energy moving forward so I can get involved in thi
> s stuff again.
I got over that last month, and right now whole towns nearby have their schools closed this week because of three illnesses at the same time, and that doesn't include all the colds and flu from Spring Break and all the college students bringing sickness home from all corners of the world. Just splurge on orange juice and nap for days. Vape-O-rub on my nose helped a lot and tons of kleenex, lots of eucalyptus cough drops. Just the lowest, meanest, ugliest cold I had in ages.
=========
-= Cloud 9 =-
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 12:41AM |
Admin Registered: 13 years ago Posts: 18,898 |
Hi Jeff,
Yup! Joey made a lot of progress here. I think we are close to verify it working. Kernel spun up the drive, and lsusb showing all good stuff.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Yup! Joey made a lot of progress here. I think we are close to verify it working. Kernel spun up the drive, and lsusb showing all good stuff.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 05:17AM |
Admin Registered: 13 years ago Posts: 18,898 |
Joey,
> All I know is, G-Parted formatted Ext4 but wouldn'
> t let me label it. So I labeled it afterwards and
> apparantly Partition Magic is running amok.
Simpler to use the Mint Menu
Accessories--> USB Stick Formatter.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> All I know is, G-Parted formatted Ext4 but wouldn'
> t let me label it. So I labeled it afterwards and
> apparantly Partition Magic is running amok.
Simpler to use the Mint Menu
Accessories--> USB Stick Formatter.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 08:10AM |
Registered: 11 years ago Posts: 1,303 |
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 11:35AM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> Simpler to use the Mint Menu
> > Accessories--> USB Stick Formatter.
Nice, didn't know that! Here we go!
habibie Wrote:
-------------------------------------------------------
> Joey,
>
> When all dust settles, perhaps do a throughput tes
> t with the hdparm utility.
Aye eye Capt.
Here's where I'm at now:
Again I could be wrong but something is kicking out RDP session as well as knocking the JoeyUSB3 folder off the LAN, which never could overcome Read-only. I'll take a break, try to dig up my UltraFit receipt...
So close, yet so far. I've got to get a few bucks and get up to BestBuy, at least have a 2nd opinion - and no UltraFits this time. :-)
=========
-= Cloud 9 =-
Edited 4 time(s). Last edit at 03/16/2017 02:44PM by JoeyPogoPlugE02.
-------------------------------------------------------
> Simpler to use the Mint Menu
> > Accessories--> USB Stick Formatter.
Nice, didn't know that! Here we go!
habibie Wrote:
-------------------------------------------------------
> Joey,
>
> When all dust settles, perhaps do a throughput tes
> t with the hdparm utility.
Aye eye Capt.
fdisk -l
root@DebianPlug:~# fdisk -l Disk /dev/mtdblock0: 14 MiB, 14680064 bytes, 28672 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xaaaaaaaa Device Boot Start End Sectors Size Id Type /dev/mtdblock0p1 ? 2863311530 5726623059 2863311530 1.3T aa unknown /dev/mtdblock0p2 ? 2863311530 5726623059 2863311530 1.3T aa unknown /dev/mtdblock0p3 ? 2863311530 4294989139 1431677610 682.7G aa unknown /dev/mtdblock0p4 ? 2863311530 5721052499 2857740970 1.3T aa unknown Disk /dev/mtdblock1: 114 MiB, 119537664 bytes, 233472 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/sda: 7.3 GiB, 7849115648 bytes, 15330304 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x01ecce21 Device Boot Start End Sectors Size Id Type /dev/sda1 2048 15147007 15144960 7.2G 83 Linux Disk /dev/zram0: 22.1 MiB, 23220224 bytes, 5669 sectors Units: sectors of 1 * 4096 = 4096 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk /dev/zram1: 22.1 MiB, 23220224 bytes, 5669 sectors Units: sectors of 1 * 4096 = 4096 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk /dev/zram2: 22.1 MiB, 23220224 bytes, 5669 sectors Units: sectors of 1 * 4096 = 4096 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk /dev/zram3: 22.1 MiB, 23220224 bytes, 5669 sectors Units: sectors of 1 * 4096 = 4096 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk /dev/sdb: 28.7 GiB, 30752000000 bytes, 60062500 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x1c5c7ba6 Device Boot Start End Sectors Size Id Type /dev/sdb1 2048 60061695 60059648 28.7G 83 Linux root@DebianPlug:~#
dmesg
root@DebianPlug:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.48-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP PREEMPT Wed Feb 15 02:59:11 PST 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Pogoplug V3 Pro
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat c08a6980, node_mem_map c7ef9000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @c7eda000 s17696 r8192 d23264 u49152
[ 0.000000] pcpu-alloc: s17696 r8192 d23264 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 117048K/131072K available (6406K kernel code, 288K rwdata, 1908K rodata, 228K init, 247K bss, 14024K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0826ddc (8316 kB)
.init : 0xc0827000 - 0xc0860000 ( 228 kB)
.data : 0xc0860000 - 0xc08a8338 ( 289 kB)
.bss : 0xc08a8338 - 0xc08e6310 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.000161] Console: colour dummy device 80x30
[ 0.000192] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.050022] pid_max: default: 32768 minimum: 301
[ 0.050186] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.050204] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.051008] Initializing cgroup subsys net_cls
[ 0.051089] CPU: Testing write buffer coherency: ok
[ 0.051514] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.190136] Brought up 2 CPUs
[ 0.190159] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.190942] devtmpfs: initialized
[ 0.195847] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.196108] prandom: seed boundary self test passed
[ 0.200524] prandom: 100 self tests passed
[ 0.200552] pinctrl core: initialized pinctrl subsystem
[ 0.201390] NET: Registered protocol family 16
[ 0.201927] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.230018] cpuidle: using governor ladder
[ 0.260011] cpuidle: using governor menu
[ 0.265075] gpio-oxnas 44000000.gpio: at address c8848000
[ 0.265459] gpio-oxnas 44100000.gpio: at address c884a000
[ 0.266019] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.388679] oxnas-pcie 47c00000.pcie-controller: PCIe version/deviceID 0x82510b5
[ 0.388797] oxnas-pcie 47c00000.pcie-controller: link up
[ 0.389109] oxnas-pcie 47c00000.pcie-controller: PCI host bridge to bus 0000:00
[ 0.389135] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[ 0.389153] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[ 0.389171] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
[ 0.389189] pci_bus 0000:00: root bus resource [bus 00-7f]
[ 0.389253] pci 0000:00:00.0: [1912:0015] type 00 class 0x0c0330
[ 0.389345] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[ 0.389527] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 0.389880] PCI: bus0: Fast back to back transfers disabled
[ 0.390039] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x48001fff 64bit]
[ 0.390510] vgaarb: loaded
[ 0.391001] SCSI subsystem initialized
[ 0.391362] libata version 3.00 loaded.
[ 0.391879] usbcore: registered new interface driver usbfs
[ 0.391987] usbcore: registered new interface driver hub
[ 0.392143] usbcore: registered new device driver usb
[ 0.392350] pps_core: LinuxPPS API ver. 1 registered
[ 0.392366] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.392412] PTP clock support registered
[ 0.394534] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.413050] NET: Registered protocol family 2
[ 0.413931] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.413972] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.414005] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.414105] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.414149] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.414423] NET: Registered protocol family 1
[ 0.414968] RPC: Registered named UNIX socket transport module.
[ 0.414988] RPC: Registered udp transport module.
[ 0.414999] RPC: Registered tcp transport module.
[ 0.415009] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.415070] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 0.415139] PCI: CLS 32 bytes, default 32
[ 0.415482] Unpacking initramfs...
[ 0.804641] Freeing initrd memory: 3644K (c7a99000 - c7e28000)
[ 0.806054] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.806225] Initialise system trusted keyring
[ 0.832619] zbud: loaded
[ 0.851379] NFS: Registering the id_resolver key type
[ 0.851448] Key type id_resolver registered
[ 0.851463] Key type id_legacy registered
[ 0.851504] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.851527] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.852431] fuse init (API version 7.23)
[ 0.854440] Key type big_key registered
[ 0.944156] Key type asymmetric registered
[ 0.944189] Asymmetric key parser 'x509' registered
[ 0.944317] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.944343] io scheduler noop registered
[ 0.944363] io scheduler deadline registered
[ 0.944422] io scheduler cfq registered (default)
[ 0.945070] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.946639] console [ttyS0] disabled
[ 0.946731] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.532029] console [ttyS0] enabled
[ 1.546787] loop: module loaded
[ 1.798791] scsi host0: sata_oxnas
[ 1.852032] ata1: SATA max UDMA/133 irq 7
[ 1.856117] sata_oxnas: resetting SATA core
[ 1.857136] nand: Could not find valid ONFI parameter page; aborting
[ 1.857180] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 1.857187] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 1.857195] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.857213] Scanning device for bad blocks
[ 1.938984] 2 ofpart partitions found on MTD device 41000000.nand
[ 1.945072] Creating 2 MTD partitions on "41000000.nand":
[ 1.950481] 0x000000000000-0x000000e00000 : "boot"
[ 1.957199] 0x000000e00000-0x000008000000 : "data"
[ 1.964462] oxnas-gmac 40400000.ethernet: no reset control found
[ 1.970485] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 1.975511] Ring mode enabled
[ 1.978547] DMA HW capability register supported
[ 1.983068] Enhanced/Alternate descriptors
[ 1.987402] Enabled extended descriptors
[ 1.991403] RX Checksum Offload Engine supported (type 2)
[ 1.996861] TX Checksum insertion supported
[ 2.001121] Wake-Up On Lan supported
[ 2.004761] Enable RX Mitigation via HW Watchdog Timer
[ 2.045140] libphy: stmmac: probed
[ 2.048535] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 2.054999] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 2.061660] PPP generic driver version 2.4.2
[ 2.066472] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.073041] ehci-pci: EHCI PCI platform driver
[ 2.077834] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 2.083438] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 2.091271] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 2.110149] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 2.116469] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.123266] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.130475] usb usb1: Product: EHCI Host Controller
[ 2.135329] usb usb1: Manufacturer: Linux 4.4.48-oxnas-tld-1 ehci_hcd
[ 2.141752] usb usb1: SerialNumber: 40200100.ehci
[ 2.147374] hub 1-0:1.0: USB hub found
[ 2.151239] hub 1-0:1.0: 2 ports detected
[ 2.156247] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 2.161546] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 2
[ 2.174456] xhci_hcd 0000:00:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x00000090
[ 2.183319] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.190077] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.197309] usb usb2: Product: xHCI Host Controller
[ 2.202186] usb usb2: Manufacturer: Linux 4.4.48-oxnas-tld-1 xhci-hcd
[ 2.208596] usb usb2: SerialNumber: 0000:00:00.0
[ 2.214164] hub 2-0:1.0: USB hub found
[ 2.217981] hub 2-0:1.0: 2 ports detected
[ 2.222940] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 2.228162] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 3
[ 2.235745] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.240010] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.249482] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.256463] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.263697] usb usb3: Product: xHCI Host Controller
[ 2.268554] usb usb3: Manufacturer: Linux 4.4.48-oxnas-tld-1 xhci-hcd
[ 2.274987] usb usb3: SerialNumber: 0000:00:00.0
[ 2.280655] hub 3-0:1.0: USB hub found
[ 2.284464] hub 3-0:1.0: 2 ports detected
[ 2.289571] usbcore: registered new interface driver cdc_acm
[ 2.295244] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.303360] usbcore: registered new interface driver cdc_wdm
[ 2.309214] usbcore: registered new interface driver usb-storage
[ 2.315407] usbcore: registered new interface driver usbserial
[ 2.321602] usbcore: registered new interface driver usbserial_generic
[ 2.328166] usbserial: USB Serial support registered for generic
[ 2.334602] mousedev: PS/2 mouse device common for all mice
[ 2.340400] i2c /dev entries driver
[ 2.345162] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.351057] usbcore: registered new interface driver usbhid
[ 2.356605] usbhid: USB HID core driver
[ 2.362613] NET: Registered protocol family 10
[ 2.380766] sit: IPv6 over IPv4 tunneling driver
[ 2.386334] NET: Registered protocol family 17
[ 2.391618] Key type dns_resolver registered
[ 2.397153] registered taskstats version 1
[ 2.401305] Loading compiled-in X.509 certificates
[ 2.406266] zswap: loaded using pool lzo/zbud
[ 2.426242] Key type encrypted registered
[ 2.433507] Freeing unused kernel memory: 228K (c0827000 - c0860000)
[ 2.470213] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[ 2.577029] udevd[99]: starting version 175
[ 2.632655] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.639339] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.655516] usb 1-1: Product: USB2.0 Hub
[ 2.681845] hub 1-1:1.0: USB hub found
[ 2.710208] hub 1-1:1.0: 4 ports detected
[ 3.020241] usb 1-1.1: new high-speed USB device number 3 using oxnas-ehci
[ 3.141301] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5575
[ 3.148154] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.155463] usb 1-1.1: Product: Cruzer Glide
[ 3.159713] usb 1-1.1: Manufacturer: SanDisk
[ 3.163980] usb 1-1.1: SerialNumber: 4C530201370809103182
[ 3.170626] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 3.177392] scsi host1: usb-storage 1-1.1:1.0
[ 3.205201] usbcore: registered new interface driver uas
[ 4.182054] scsi 1:0:0:0: Direct-Access SanDisk Cruzer Glide 1.27 PQ: 0 ANSI: 6
[ 4.194700] sd 1:0:0:0: [sda] 15330304 512-byte logical blocks: (7.85 GB/7.31 GiB)
[ 4.204078] sd 1:0:0:0: [sda] Write Protect is off
[ 4.208875] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 4.209789] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.229381] sda: sda1
[ 4.237304] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 13.526901] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 13.601272] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 15.067394] udevd[295]: starting version 175
[ 17.103572] random: nonblocking pool is initialized
[ 17.273640] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 17.543549] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 20.721797] Adding 1048572k swap on /swapfile1. Priority:-1 extents:360 across:1169636k FS
[ 23.701808] zram: Added device: zram0
[ 23.732390] zram: Added device: zram1
[ 23.753868] zram: Added device: zram2
[ 23.783664] zram: Added device: zram3
[ 23.808320] zram0: detected capacity change from 0 to 23220224
[ 23.882365] Adding 22672k swap on /dev/zram0. Priority:10 extents:1 across:22672k SSFS
[ 23.893550] zram1: detected capacity change from 0 to 23220224
[ 23.949304] Adding 22672k swap on /dev/zram1. Priority:10 extents:1 across:22672k SSFS
[ 23.960486] zram2: detected capacity change from 0 to 23220224
[ 24.032481] Adding 22672k swap on /dev/zram2. Priority:10 extents:1 across:22672k SSFS
[ 24.043458] zram3: detected capacity change from 0 to 23220224
[ 24.111585] Adding 22672k swap on /dev/zram3. Priority:10 extents:1 across:22672k SSFS
[ 29.210296] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 32.210273] oxnas-gmac 40400000.ethernet eth0: Link is Down
[ 33.210288] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 36.210265] oxnas-gmac 40400000.ethernet eth0: Link is Down
[ 37.210291] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 40.210293] oxnas-gmac 40400000.ethernet eth0: Link is Down
[ 41.210296] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 64.594460] zram: Cannot change disksize for initialized device
[ 64.651051] zram: Cannot change disksize for initialized device
[ 64.716715] zram: Cannot change disksize for initialized device
[ 64.770606] zram: Cannot change disksize for initialized device
[ 222.550750] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 222.575477] usb 3-1: New USB device found, idVendor=0781, idProduct=5583
[ 222.582241] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 222.589355] usb 3-1: Product: Ultra Fit
[ 222.593216] usb 3-1: Manufacturer: SanDisk
[ 222.597299] usb 3-1: SerialNumber: 4C530001180525105180
[ 222.605544] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 222.630338] scsi host2: usb-storage 3-1:1.0
[ 223.632115] scsi 2:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6
[ 223.643496] sd 2:0:0:0: [sdb] 60062500 512-byte logical blocks: (30.8 GB/28.6 GiB)
[ 223.655313] sd 2:0:0:0: [sdb] Write Protect is off
[ 223.661634] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 223.662981] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 223.690969] sdb: sdb1
[ 223.704046] sd 2:0:0:0: [sdb] Attached SCSI removable disk
root@DebianPlug:~#
lusb
root@DebianPlug:~# lsusb Bus 003 Device 002: ID 0781:5583 SanDisk Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 0781:5575 SanDisk Corp. Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@DebianPlug:~# lsusb Bus 003 Device 002: ID 0781:5583 SanDisk Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 0781:5575 SanDisk Corp. Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@DebianPlug:~#
lsusb -vvv
root@DebianPlug:~# lsusb -vvv
Bus 003 Device 002: ID 0781:5583 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0781 SanDisk Corp.
idProduct 0x5583
bcdDevice 1.00
iManufacturer 1 SanDisk
iProduct 2 Ultra Fit
iSerial 3 4C530001180525105180
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 44
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 224mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 256 micro seconds
Device Status: 0x0000
(Bus Powered)
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Hub Descriptor:
bLength 12
bDescriptorType 42
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
bHubDecLat 0.0 micro seconds
wHubDelay 0 nano seconds
DeviceRemovable 0x00
Hub Port Status:
Port 1: 0000.0203 5Gbps power U0 enable connect
Port 2: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 15
bNumDeviceCaps 1
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x02
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x0008
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 3
Lowest fully-functional device speed is SuperSpeed (5Gbps)
bU1DevExitLat 0 micro seconds
bU2DevExitLat 0 micro seconds
Device Status: 0x0001
Self Powered
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
Bus 001 Device 003: ID 0781:5575 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5575
bcdDevice 1.27
iManufacturer 1 SanDisk
iProduct 2 Cruzer Glide
iSerial 3 4C530201370809103182
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x05e3 Genesys Logic, Inc.
idProduct 0x0608 USB-2.0 4-Port HUB
bcdDevice 77.64
iManufacturer 0
iProduct 1 USB2.0 Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x00e0
Ganged power switching
Ganged overcurrent protection
TT think time 32 FS bits
Port indicators
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 100 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 40200100.ehci
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
root@DebianPlug:~#
Here's where I'm at now:
root@DebianPlug:~# mkdir -p /media/JoeyUSB3 root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3Says it's owned by 999 and won't change read/write. Now the RDP is failing that connection too. Bummer, something's askew.
Again I could be wrong but something is kicking out RDP session as well as knocking the JoeyUSB3 folder off the LAN, which never could overcome Read-only. I'll take a break, try to dig up my UltraFit receipt...
So close, yet so far. I've got to get a few bucks and get up to BestBuy, at least have a 2nd opinion - and no UltraFits this time. :-)
=========
-= Cloud 9 =-
Edited 4 time(s). Last edit at 03/16/2017 02:44PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 03:29PM |
Admin Registered: 13 years ago Posts: 18,898 |
Do you have the log for this?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
Says it's owned by 999 and won't change read/write. .
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 04:09PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> Do you have the log for this?
That's what I saw when accessing Pogo using RDP and right-clicking the JoeyUSB3 folder and going down to Properties.It had 999 for each of the different "owners" kind of thing. The Pogo is off at the moment, but I could get a screenshot if you're interested. So the 2nd dropdown of "owner", groups set that to sambashare and try to change from read only to RW and you get that error message.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/16/2017 04:15PM by JoeyPogoPlugE02.
-------------------------------------------------------
> Do you have the log for this?
That's what I saw when accessing Pogo using RDP and right-clicking the JoeyUSB3 folder and going down to Properties.It had 999 for each of the different "owners" kind of thing. The Pogo is off at the moment, but I could get a screenshot if you're interested. So the 2nd dropdown of "owner", groups set that to sambashare and try to change from read only to RW and you get that error message.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/16/2017 04:15PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 05:36PM |
Admin Registered: 13 years ago Posts: 18,898 |
Joey,
Don't use RDP at the moment.
Us SSH to login and do everything at command line.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Don't use RDP at the moment.
Us SSH to login and do everything at command line.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 16, 2017 06:36PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> Joey,
>
> Don't use RDP at the moment.
>
> Us SSH to login and do everything at command line.
Right, I'd only went there if I knew it was over my head, about to poweroff and looking for any clues.
=========
-= Cloud 9 =-
-------------------------------------------------------
> Joey,
>
> Don't use RDP at the moment.
>
> Us SSH to login and do everything at command line.
Right, I'd only went there if I knew it was over my head, about to poweroff and looking for any clues.
=========
-= Cloud 9 =-
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 17, 2017 01:37PM |
Registered: 9 years ago Posts: 1,516 |
Cool, made my way to BestBuy and got a SanDisk Ultra 32GB Red stick. This should help.
-update same formatting problems as before when using Pogoplug to format Ext4. At least it's unlikely the USB sticks are so bad.
Is yours setup Bodhi? Let me know if I can be of service.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/17/2017 07:56PM by JoeyPogoPlugE02.
-update same formatting problems as before when using Pogoplug to format Ext4. At least it's unlikely the USB sticks are so bad.
Is yours setup Bodhi? Let me know if I can be of service.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/17/2017 07:56PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 17, 2017 08:10PM |
Admin Registered: 13 years ago Posts: 18,898 |
Joey,
Not yet! but I will try later today or tomorrow.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Not yet! but I will try later today or tomorrow.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 17, 2017 08:19PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> Joey,
>
> Not yet! but I will try later today or tomorrow.
Those two USB 3.0 sockets, I can tell you this, if you plug a USB tester into one of them it can be of great help. Mine sure has been. It should only monitor power which means it'll light up if the power is properly on. One of the USB-to-Molex adapter cables I got from Malaysia are somewhat poorly connected, and a meter showed where to jiggle the cable right. As well as help me see the connectors on the molex were backwards. If/when this gets figured out, I can solder it nice and permanent. Anyway I'll be nearby.
=========
-= Cloud 9 =-
-------------------------------------------------------
> Joey,
>
> Not yet! but I will try later today or tomorrow.
Those two USB 3.0 sockets, I can tell you this, if you plug a USB tester into one of them it can be of great help. Mine sure has been. It should only monitor power which means it'll light up if the power is properly on. One of the USB-to-Molex adapter cables I got from Malaysia are somewhat poorly connected, and a meter showed where to jiggle the cable right. As well as help me see the connectors on the molex were backwards. If/when this gets figured out, I can solder it nice and permanent. Anyway I'll be nearby.
=========
-= Cloud 9 =-
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 01:08AM |
Admin Registered: 13 years ago Posts: 18,898 |
No luck. I went ahead and I swap the Molex black and yellow wires before plugging it in, it would not start the box at all. Could be the connector is already correct.
Back to the drawer for another day :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Back to the drawer for another day :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 02:24PM |
Admin Registered: 13 years ago Posts: 18,898 |
It looks like we don't have enough power. The card must be drawing too much power upon power up.
I'll to try either plugging in after booted, or with a separate power source (such as USB charger) for the USB power connector end.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I'll to try either plugging in after booted, or with a separate power source (such as USB charger) for the USB power connector end.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 02:41PM |
Registered: 9 years ago Posts: 1,516 |
Wow, the thought of too low power never occurred to me. I'm now trying an eCigarette charger, which is trying to format it again. I notice it never got formatted yesterday, it stayed at SanDisk's own Fat 32 (?).
I'm near the appalling possibility this takes full molex power, meaning 12v too.
Like usual, formatting it's seems to be stuck on:
I'll wait this out a while...
=========
-= Cloud 9 =-
Edited 2 time(s). Last edit at 03/18/2017 04:17PM by JoeyPogoPlugE02.
I'm near the appalling possibility this takes full molex power, meaning 12v too.
Like usual, formatting it's seems to be stuck on:
Creating journal (32768 blocks):
I'll wait this out a while...
=========
-= Cloud 9 =-
Edited 2 time(s). Last edit at 03/18/2017 04:17PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 04:16PM |
Admin Registered: 13 years ago Posts: 18,898 |
JoeyPogoPlugE02 Wrote:
-------------------------------------------------------
> Wow, that thought never occurred to me. I could tr
> y a higher power supply, maybe an eCigarette charg
> er or maybe you have a cellphone USB charger...
Sure, that would be better than power it up after.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Wow, that thought never occurred to me. I could tr
> y a higher power supply, maybe an eCigarette charg
> er or maybe you have a cellphone USB charger...
Sure, that would be better than power it up after.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 05:19PM |
Registered: 9 years ago Posts: 1,516 |
The eCig adapter didn't make a difference, so now i'm trying one of those Molex adapters that are used to power a 3.5" hard drive, with the 5 and 12v.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/18/2017 05:30PM by JoeyPogoPlugE02.
root@DebianPlug:~# mkdir -p /media/JoeyUSB3 root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3 mount: /dev/sdb1: can't read superblock root@DebianPlug:~#
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/18/2017 05:30PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 05:51PM |
Admin Registered: 13 years ago Posts: 18,898 |
>
Joey,
This is a low level file system software error, not hardware. So your process to partition and format might have been faulty.
At the shell commandline (root@DebianPlug:~#):
Then enter fdisk
and then at the > prompt, execute these command: lowercase o to clear all partitions, lowecase n to create new partition
And then hit <Enter> for the rest of the questions to take default value.
Finally, when no longer any question at the > prompt, execute the last command: lowercase w to accept all changes
Proceed to format it
and then sync
Then mount the drive again
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/18/2017 05:53PM by bodhi.
> root@DebianPlug:~# mkdir -p /media/JoeyUSB3 > root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3 > mount: /dev/sdb1: can't read superblock > root@DebianPlug:~# > >
Joey,
This is a low level file system software error, not hardware. So your process to partition and format might have been faulty.
At the shell commandline (root@DebianPlug:~#):
umount /media/JoeyUSB3
Then enter fdisk
fdisk /dev/sdb
and then at the > prompt, execute these command: lowercase o to clear all partitions, lowecase n to create new partition
o n
And then hit <Enter> for the rest of the questions to take default value.
Finally, when no longer any question at the > prompt, execute the last command: lowercase w to accept all changes
w
Proceed to format it
mkfs.ext3 -L JoeyUSB3 /dev/sdb1
and then sync
sync
Then mount the drive again
mkdir -p /media/JoeyUSB3 mount -o noatime /dev/sdb1 /media/JoeyUSB3
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/18/2017 05:53PM by bodhi.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 06:35PM |
Registered: 9 years ago Posts: 1,516 |
Nothing works. I have no idea if the unit is bad, or what. It gets to a point I've tried prepping so many ways, including formatting Ext3 instead of Ext4, and now using all four power connectors on the USB 3 unit. The last things I can think of physically would be to put an electrical insulator between the unit and Pogoplug circuit board in case anything is touching metal to metal, or maybe even if those were a 1/2 height like you said, i wonder if the mounting screws are used to also ground with boards.
Back to the page we bought this from, I see three items of interest:
* Internal FDD Power Connector for Supplying +5V Power to the USB Port
* Do NOT support MSATA slot
* Must connect 4pin power while using
Here's some highlight pieces from the last try.
No idea.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/18/2017 09:36PM by JoeyPogoPlugE02.
Back to the page we bought this from, I see three items of interest:
* Internal FDD Power Connector for Supplying +5V Power to the USB Port
* Do NOT support MSATA slot
* Must connect 4pin power while using
Here's some highlight pieces from the last try.
root@DebianPlug:~# mkfs.ext3 -L JoeyUSB3 /dev/sdb1 mke2fs 1.42.12 (29-Aug-2014) The file /dev/sdb1 does not exist and no size was specified.
mount: special device /dev/sdb1 does not exist
root@DebianPlug:~# mkdir -p /media/JoeyUSB3 root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3 mount: /dev/sdb1: can't read superblock root@DebianPlug:~# umount /media/JoeyUSB3 umount: /media/JoeyUSB3: not mounted
No idea.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/18/2017 09:36PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 09:59PM |
Admin Registered: 13 years ago Posts: 18,898 |
Do you have log of fdisk /dev/sdb ?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 18, 2017 11:38PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> Do you have log of fdisk /dev/sdb ?
I don't think so and don't know the code. This time I've un-formatted the USB stick and here's some results:
I wonder if something about this is set to read-only or something? Do you see evidence Pogo is writing to this at all? It seems to write labels if the directory is locally mounted but maybe a hair off the driver is missing or something.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/19/2017 12:22AM by JoeyPogoPlugE02.
-------------------------------------------------------
> Do you have log of fdisk /dev/sdb ?
I don't think so and don't know the code. This time I've un-formatted the USB stick and here's some results:
fdisk -l dmesg lsusb
root@DebianPlug:~# fdisk -l
Disk /dev/mtdblock0: 14 MiB, 14680064 bytes, 28672 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xaaaaaaaa
Device Boot Start End Sectors Size Id Type
/dev/mtdblock0p1 ? 2863311530 5726623059 2863311530 1.3T aa unknown
/dev/mtdblock0p2 ? 2863311530 5726623059 2863311530 1.3T aa unknown
/dev/mtdblock0p3 ? 2863311530 4294989139 1431677610 682.7G aa unknown
/dev/mtdblock0p4 ? 2863311530 5721052499 2857740970 1.3T aa unknown
Disk /dev/mtdblock1: 114 MiB, 119537664 bytes, 233472 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk /dev/sda: 7.3 GiB, 7849115648 bytes, 15330304 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x01ecce21
Device Boot Start End Sectors Size Id Type
/dev/sda1 2048 15147007 15144960 7.2G 83 Linux
Disk /dev/zram0: 22.1 MiB, 23220224 bytes, 5669 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/zram1: 22.1 MiB, 23220224 bytes, 5669 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/zram2: 22.1 MiB, 23220224 bytes, 5669 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/zram3: 22.1 MiB, 23220224 bytes, 5669 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/sdb: 28.7 GiB, 30752000000 bytes, 60062500 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x2bcdd776
root@DebianPlug:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.48-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP PREEMPT Wed Feb 15 02:59:11 PST 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Pogoplug V3 Pro
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat c08a6980, node_mem_map c7ef9000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @c7eda000 s17696 r8192 d23264 u49152
[ 0.000000] pcpu-alloc: s17696 r8192 d23264 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 117048K/131072K available (6406K kernel code, 288K rwdata, 1908K rodata, 228K init, 247K bss, 14024K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0826ddc (8316 kB)
.init : 0xc0827000 - 0xc0860000 ( 228 kB)
.data : 0xc0860000 - 0xc08a8338 ( 289 kB)
.bss : 0xc08a8338 - 0xc08e6310 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.000163] Console: colour dummy device 80x30
[ 0.000192] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.050024] pid_max: default: 32768 minimum: 301
[ 0.050186] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.050206] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.051010] Initializing cgroup subsys net_cls
[ 0.051092] CPU: Testing write buffer coherency: ok
[ 0.051514] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.190138] Brought up 2 CPUs
[ 0.190161] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.190942] devtmpfs: initialized
[ 0.195750] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.196003] prandom: seed boundary self test passed
[ 0.200419] prandom: 100 self tests passed
[ 0.200445] pinctrl core: initialized pinctrl subsystem
[ 0.201256] NET: Registered protocol family 16
[ 0.201799] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.230018] cpuidle: using governor ladder
[ 0.260014] cpuidle: using governor menu
[ 0.265090] gpio-oxnas 44000000.gpio: at address c8848000
[ 0.265469] gpio-oxnas 44100000.gpio: at address c884a000
[ 0.266050] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.389186] oxnas-pcie 47c00000.pcie-controller: PCIe version/deviceID 0x82510b5
[ 0.389304] oxnas-pcie 47c00000.pcie-controller: link up
[ 0.389611] oxnas-pcie 47c00000.pcie-controller: PCI host bridge to bus 0000:00
[ 0.389637] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[ 0.389655] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[ 0.389670] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
[ 0.389688] pci_bus 0000:00: root bus resource [bus 00-7f]
[ 0.389747] pci 0000:00:00.0: [1912:0015] type 00 class 0x0c0330
[ 0.389836] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[ 0.390077] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 0.390438] PCI: bus0: Fast back to back transfers disabled
[ 0.390535] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x48001fff 64bit]
[ 0.391004] vgaarb: loaded
[ 0.391488] SCSI subsystem initialized
[ 0.391841] libata version 3.00 loaded.
[ 0.392360] usbcore: registered new interface driver usbfs
[ 0.392471] usbcore: registered new interface driver hub
[ 0.392629] usbcore: registered new device driver usb
[ 0.392837] pps_core: LinuxPPS API ver. 1 registered
[ 0.392852] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.392901] PTP clock support registered
[ 0.395010] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.413478] NET: Registered protocol family 2
[ 0.414356] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.414397] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.414430] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.414528] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.414568] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.414830] NET: Registered protocol family 1
[ 0.415370] RPC: Registered named UNIX socket transport module.
[ 0.415390] RPC: Registered udp transport module.
[ 0.415400] RPC: Registered tcp transport module.
[ 0.415411] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.415472] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 0.415544] PCI: CLS 32 bytes, default 32
[ 0.415869] Unpacking initramfs...
[ 0.806725] Freeing initrd memory: 3644K (c7a99000 - c7e28000)
[ 0.808153] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.808325] Initialise system trusted keyring
[ 0.833036] zbud: loaded
[ 0.851404] NFS: Registering the id_resolver key type
[ 0.851479] Key type id_resolver registered
[ 0.851494] Key type id_legacy registered
[ 0.851537] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.851563] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.852495] fuse init (API version 7.23)
[ 0.854512] Key type big_key registered
[ 0.953617] Key type asymmetric registered
[ 0.953651] Asymmetric key parser 'x509' registered
[ 0.953781] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.953807] io scheduler noop registered
[ 0.953825] io scheduler deadline registered
[ 0.953886] io scheduler cfq registered (default)
[ 0.954536] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.956108] console [ttyS0] disabled
[ 0.956203] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.541419] console [ttyS0] enabled
[ 1.556236] loop: module loaded
[ 1.808204] scsi host0: sata_oxnas
[ 1.861463] ata1: SATA max UDMA/133 irq 7
[ 1.865551] sata_oxnas: resetting SATA core
[ 1.866588] nand: Could not find valid ONFI parameter page; aborting
[ 1.866631] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 1.866636] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 1.866644] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.866662] Scanning device for bad blocks
[ 1.950090] 2 ofpart partitions found on MTD device 41000000.nand
[ 1.956177] Creating 2 MTD partitions on "41000000.nand":
[ 1.961584] 0x000000000000-0x000000e00000 : "boot"
[ 1.968314] 0x000000e00000-0x000008000000 : "data"
[ 1.975603] oxnas-gmac 40400000.ethernet: no reset control found
[ 1.981624] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 1.986649] Ring mode enabled
[ 1.989683] DMA HW capability register supported
[ 1.994204] Enhanced/Alternate descriptors
[ 1.998538] Enabled extended descriptors
[ 2.002536] RX Checksum Offload Engine supported (type 2)
[ 2.007989] TX Checksum insertion supported
[ 2.012331] Wake-Up On Lan supported
[ 2.015974] Enable RX Mitigation via HW Watchdog Timer
[ 2.056010] libphy: stmmac: probed
[ 2.059407] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 2.065871] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 2.072560] PPP generic driver version 2.4.2
[ 2.077409] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.083975] ehci-pci: EHCI PCI platform driver
[ 2.088770] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 2.094312] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 2.102146] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 2.120153] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 2.126456] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.133253] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.140462] usb usb1: Product: EHCI Host Controller
[ 2.145315] usb usb1: Manufacturer: Linux 4.4.48-oxnas-tld-1 ehci_hcd
[ 2.151744] usb usb1: SerialNumber: 40200100.ehci
[ 2.157391] hub 1-0:1.0: USB hub found
[ 2.161256] hub 1-0:1.0: 2 ports detected
[ 2.166261] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 2.171558] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 2
[ 2.184468] xhci_hcd 0000:00:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x00000090
[ 2.193333] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.200138] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.207326] usb usb2: Product: xHCI Host Controller
[ 2.212203] usb usb2: Manufacturer: Linux 4.4.48-oxnas-tld-1 xhci-hcd
[ 2.218611] usb usb2: SerialNumber: 0000:00:00.0
[ 2.224194] hub 2-0:1.0: USB hub found
[ 2.228008] hub 2-0:1.0: 2 ports detected
[ 2.232916] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 2.238136] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 3
[ 2.245716] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.250012] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.259458] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.266439] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.273671] usb usb3: Product: xHCI Host Controller
[ 2.278528] usb usb3: Manufacturer: Linux 4.4.48-oxnas-tld-1 xhci-hcd
[ 2.284961] usb usb3: SerialNumber: 0000:00:00.0
[ 2.290600] hub 3-0:1.0: USB hub found
[ 2.294412] hub 3-0:1.0: 2 ports detected
[ 2.299530] usbcore: registered new interface driver cdc_acm
[ 2.305205] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.313320] usbcore: registered new interface driver cdc_wdm
[ 2.319173] usbcore: registered new interface driver usb-storage
[ 2.325370] usbcore: registered new interface driver usbserial
[ 2.331568] usbcore: registered new interface driver usbserial_generic
[ 2.338127] usbserial: USB Serial support registered for generic
[ 2.344555] mousedev: PS/2 mouse device common for all mice
[ 2.350351] i2c /dev entries driver
[ 2.355133] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.361031] usbcore: registered new interface driver usbhid
[ 2.366581] usbhid: USB HID core driver
[ 2.372523] NET: Registered protocol family 10
[ 2.378478] sit: IPv6 over IPv4 tunneling driver
[ 2.384092] NET: Registered protocol family 17
[ 2.388710] Key type dns_resolver registered
[ 2.394526] registered taskstats version 1
[ 2.398643] Loading compiled-in X.509 certificates
[ 2.403573] zswap: loaded using pool lzo/zbud
[ 2.423810] Key type encrypted registered
[ 2.443043] Freeing unused kernel memory: 228K (c0827000 - c0860000)
[ 2.480189] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[ 2.585354] udevd[99]: starting version 175
[ 2.642667] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.649349] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.680202] usb 1-1: Product: USB2.0 Hub
[ 2.700526] hub 1-1:1.0: USB hub found
[ 2.709980] hub 1-1:1.0: 4 ports detected
[ 3.011448] usb 1-1.1: new high-speed USB device number 3 using oxnas-ehci
[ 3.131304] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5575
[ 3.138158] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.145574] usb 1-1.1: Product: Cruzer Glide
[ 3.149826] usb 1-1.1: Manufacturer: SanDisk
[ 3.154099] usb 1-1.1: SerialNumber: 4C530201370809103182
[ 3.161303] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 3.168094] scsi host1: usb-storage 1-1.1:1.0
[ 3.196536] usbcore: registered new interface driver uas
[ 4.171425] scsi 1:0:0:0: Direct-Access SanDisk Cruzer Glide 1.27 PQ: 0 ANSI: 6
[ 4.184642] sd 1:0:0:0: [sda] 15330304 512-byte logical blocks: (7.85 GB/7.31 GiB)
[ 4.194053] sd 1:0:0:0: [sda] Write Protect is off
[ 4.198845] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 4.199795] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.219225] sda: sda1
[ 4.230929] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 13.502149] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 13.525957] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 15.028815] udevd[296]: starting version 175
[ 17.059816] random: nonblocking pool is initialized
[ 17.216276] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 17.491069] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 20.633436] Adding 1048572k swap on /swapfile1. Priority:-1 extents:360 across:1169636k FS
[ 23.451589] zram: Added device: zram0
[ 23.471526] zram: Added device: zram1
[ 23.485002] zram: Added device: zram2
[ 23.511454] zram: Added device: zram3
[ 23.542691] zram0: detected capacity change from 0 to 23220224
[ 23.613575] Adding 22672k swap on /dev/zram0. Priority:10 extents:1 across:22672k SSFS
[ 23.626035] zram1: detected capacity change from 0 to 23220224
[ 23.694005] Adding 22672k swap on /dev/zram1. Priority:10 extents:1 across:22672k SSFS
[ 23.708748] zram2: detected capacity change from 0 to 23220224
[ 23.769879] Adding 22672k swap on /dev/zram2. Priority:10 extents:1 across:22672k SSFS
[ 23.781509] zram3: detected capacity change from 0 to 23220224
[ 23.864025] Adding 22672k swap on /dev/zram3. Priority:10 extents:1 across:22672k SSFS
[ 29.150161] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 56.107079] zram: Cannot change disksize for initialized device
[ 56.163601] zram: Cannot change disksize for initialized device
[ 56.222108] zram: Cannot change disksize for initialized device
[ 56.287083] zram: Cannot change disksize for initialized device
[ 507.340761] usb 3-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 507.365181] usb 3-2: New USB device found, idVendor=0781, idProduct=5581
[ 507.371921] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 507.379028] usb 3-2: Product: Ultra
[ 507.382543] usb 3-2: Manufacturer: SanDisk
[ 507.386887] usb 3-2: SerialNumber: 4C530001320111116341
[ 507.401889] usb-storage 3-2:1.0: USB Mass Storage device detected
[ 507.420495] scsi host2: usb-storage 3-2:1.0
[ 508.421844] scsi 2:0:0:0: Direct-Access SanDisk Ultra 1.00 PQ: 0 ANSI: 6
[ 508.436049] sd 2:0:0:0: [sdb] 60062500 512-byte logical blocks: (30.8 GB/28.6 GiB)
[ 508.446438] sd 2:0:0:0: [sdb] Write Protect is off
[ 508.452057] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 508.453457] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 508.477493] sdb:
[ 508.484108] sd 2:0:0:0: [sdb] Attached SCSI removable disk
root@DebianPlug:~# lsusb
Bus 003 Device 002: ID 0781:5581 SanDisk Corp.
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0781:5575 SanDisk Corp.
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@DebianPlug:~# fdisk /dev/sdb
Welcome to fdisk (util-linux 2.25.2).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): o
Created a new DOS disklabel with disk identifier 0x59bb311c.
Command (m for help): n
Partition type
p primary (0 primary, 0 extended, 4 free)
e extended (container for logical partitions)
Select (default p):
Using default response p.
Partition number (1-4, default 1):
First sector (2048-60062499, default 2048):
Last sector, +sectors or +size{K,M,G,T,P} (2048-60062499, default 60062499):
Created a new partition 1 of type 'Linux' and of size 28.7 GiB.
Command (m for help): w
The partition table has been altered.
Calling ioctl() to re-read partition table.
Syncing disks.
root@DebianPlug:~# mkfs.ext3 -L JoeyUSB3 /dev/sdb1
mke2fs 1.42.12 (29-Aug-2014)
The file /dev/sdb1 does not exist and no size was specified.
root@DebianPlug:~# sync
root@DebianPlug:~# mkdir -p /media/JoeyUSB3
root@DebianPlug:~# mount -o noatime /dev/sdb1 /media/JoeyUSB3
mount: special device /dev/sdb1 does not exist
root@DebianPlug:~#
I wonder if something about this is set to read-only or something? Do you see evidence Pogo is writing to this at all? It seems to write labels if the directory is locally mounted but maybe a hair off the driver is missing or something.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/19/2017 12:22AM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 19, 2017 12:47AM |
Admin Registered: 13 years ago Posts: 18,898 |
Joey,
> > Do you have log of fdisk /dev/sdb ?
>
> I don't think so and don't know the code. This tim
> e I've un-formatted the USB stick and here's some
> results:
You did already! here:
> root@DebianPlug:~# fdisk /dev/sdb
>
> Welcome to fdisk (util-linux 2.25.2).
> Changes will remain in memory only, until you deci
> de to write them.
> Be careful before using the write command.
>
>
> Command (m for help): o
> Created a new DOS disklabel with disk identifier 0
> x59bb311c.
>
> Command (m for help): n
> Partition type
> p primary (0 primary, 0 extended, 4 free)
> e extended (container for logical partitions)
> Select (default p):
>
> Using default response p.
> Partition number (1-4, default 1):
> First sector (2048-60062499, default 2048):
> Last sector, +sectors or +size{K,M,G,T,P} (2048-60
> 062499, default 60062499):
>
> Created a new partition 1 of type 'Linux' and of s
> ize 28.7 GiB.
>
> Command (m for help): w
> The partition table has been altered.
> Calling ioctl() to re-read partition table.
> Syncing disks.
>
> root@DebianPlug:~# mkfs.ext3 -L JoeyUSB3 /dev/sdb1
> mke2fs 1.42.12 (29-Aug-2014)
> The file /dev/sdb1 does not exist and no size was
> specified.
At this point, the sdb1 partition was not automatically populated. So just reboot
Log back into Debian.
And then
If you see sdb1 listed like below (xxx are some numbers)
then go ahead with formating to Ext3
Proceed to format it
and then sync
Then mount the drive again
And then check the mount
If it shows the /devsdb1 was mounted at /media/JoeyUSB3, then
And copy some files to it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/19/2017 12:51AM by bodhi.
> > Do you have log of fdisk /dev/sdb ?
>
> I don't think so and don't know the code. This tim
> e I've un-formatted the USB stick and here's some
> results:
You did already! here:
> root@DebianPlug:~# fdisk /dev/sdb
>
> Welcome to fdisk (util-linux 2.25.2).
> Changes will remain in memory only, until you deci
> de to write them.
> Be careful before using the write command.
>
>
> Command (m for help): o
> Created a new DOS disklabel with disk identifier 0
> x59bb311c.
>
> Command (m for help): n
> Partition type
> p primary (0 primary, 0 extended, 4 free)
> e extended (container for logical partitions)
> Select (default p):
>
> Using default response p.
> Partition number (1-4, default 1):
> First sector (2048-60062499, default 2048):
> Last sector, +sectors or +size{K,M,G,T,P} (2048-60
> 062499, default 60062499):
>
> Created a new partition 1 of type 'Linux' and of s
> ize 28.7 GiB.
>
> Command (m for help): w
> The partition table has been altered.
> Calling ioctl() to re-read partition table.
> Syncing disks.
>
> root@DebianPlug:~# mkfs.ext3 -L JoeyUSB3 /dev/sdb1
> mke2fs 1.42.12 (29-Aug-2014)
> The file /dev/sdb1 does not exist and no size was
> specified.
At this point, the sdb1 partition was not automatically populated. So just reboot
shutdown -r now
Log back into Debian.
And then
fdisk -l /dev/sdb
If you see sdb1 listed like below (xxx are some numbers)
Quote
/dev/sdb1 x xxx xxx xxx xx xxG xx Linux
then go ahead with formating to Ext3
Proceed to format it
mkfs.ext3 -L JoeyUSB3 /dev/sdb1
and then sync
sync
Then mount the drive again
mkdir -p /media/JoeyUSB3 mount -o noatime /dev/sdb1 /media/JoeyUSB3
And then check the mount
mount
If it shows the /devsdb1 was mounted at /media/JoeyUSB3, then
cd /media/JoeyUSB3
And copy some files to it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/19/2017 12:51AM by bodhi.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 19, 2017 12:15PM |
Registered: 9 years ago Posts: 1,516 |
This is what I see when rebooting:
-update - tried that and it's writing inode tables atm, one sec :-)
No it may have stopped at 34 out of 230:
Yeah it's stuck on 34/230 so I'll let it sit here for a while. Pretty cool though to get past the previous issue :-)
-update- tried it again and it appears 27 is the highest number it's reaching.
-update 2- 29 this time.
This last time I put an insulator between the USB 3.0 card and the circuit board of the Pogoplug, in case it was something like that. The only other things that cross my mind are maybe power supply in Pogoplug is anemic, or maybe my swap is incorrectly set because it gets so far before failure. Or the USB 3 unit is damaged or something.
-update 3- This time I formatted it FA32 on the ThinClient and named it: JOEYUSB3
The result of this:
I didn't find anything useful searching for answers. Mostly Ext3 & Ext4 issues with various kernels, AMD chipsets and things.
Break time.
=========
-= Cloud 9 =-
Edited 9 time(s). Last edit at 03/19/2017 04:22PM by JoeyPogoPlugE02.
root@DebianPlug:~# fdisk -l /dev/sdb Disk /dev/sdb: 28.7 GiB, 30752000000 bytes, 60062500 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x2bcdd776 root@DebianPlug:~#It doesn't have the 1 at the end. So would I format like his?
mkfs.ext3 -L JoeyUSB3 /dev/sdb
-update - tried that and it's writing inode tables atm, one sec :-)
No it may have stopped at 34 out of 230:
root@DebianPlug:~# mkfs.ext3 -L JoeyUSB3 /dev/sdb
mke2fs 1.42.12 (29-Aug-2014)
Found a dos partition table in /dev/sdb
Proceed anyway? (y,n) y
Creating filesystem with 7507812 4k blocks and 1880480 inodes
Filesystem UUID: de13380c-8b12-4fc7-878b-022f3d9063ff
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000
Allocating group tables: done
Writing inode tables: 34/230
Yeah it's stuck on 34/230 so I'll let it sit here for a while. Pretty cool though to get past the previous issue :-)
-update- tried it again and it appears 27 is the highest number it's reaching.
-update 2- 29 this time.
This last time I put an insulator between the USB 3.0 card and the circuit board of the Pogoplug, in case it was something like that. The only other things that cross my mind are maybe power supply in Pogoplug is anemic, or maybe my swap is incorrectly set because it gets so far before failure. Or the USB 3 unit is damaged or something.
-update 3- This time I formatted it FA32 on the ThinClient and named it: JOEYUSB3
The result of this:
mkdir -p /media/JoeyUSB3 mount -o noatime /dev/sdb1 /media/JoeyUSB3Is this:
mount: /dev/sdb1: can't read superblock
I didn't find anything useful searching for answers. Mostly Ext3 & Ext4 issues with various kernels, AMD chipsets and things.
Break time.
=========
-= Cloud 9 =-
Edited 9 time(s). Last edit at 03/19/2017 04:22PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 19, 2017 04:25PM |
Admin Registered: 13 years ago Posts: 18,898 |
Joey,
1. If the disk is high capacity, Ext3 will take a long time.
2. It must be sdb1 (sdb is the whole disk). sdb1 is the partition to be formatted.
Or you can try ext4. Ext4 will be very fast (it only partially formats the partition, and will slowly perform a background task to complete).
-----
BTW, my USB-molex black wire got detached (It is a very low quality job of crimping). And the USB 21 pin connector is not that great (very tight). These parts are not something I would trust. I think you need to solder them (instead of molex).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
1. If the disk is high capacity, Ext3 will take a long time.
2. It must be sdb1 (sdb is the whole disk). sdb1 is the partition to be formatted.
mkfs.ext3 -L JoeyUSB3 /dev/sdb1
Or you can try ext4. Ext4 will be very fast (it only partially formats the partition, and will slowly perform a background task to complete).
mkfs.ext4 -L JoeyUSB3 /dev/sdb1
-----
BTW, my USB-molex black wire got detached (It is a very low quality job of crimping). And the USB 21 pin connector is not that great (very tight). These parts are not something I would trust. I think you need to solder them (instead of molex).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 19, 2017 05:28PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> Joey,
>
> 1. If the disk is high capacity, Ext3 will take a
> long time.
> 2. It must be sdb1 (sdb is the whole disk). sdb1 i
> s the partition to be formatted.
>
>
> Or you can try ext4. Ext4 will be very fast (it on
> ly partially formats the partition, and will slowl
> y perform a background task to complete).
>
> -----
>
> BTW, my USB-molex black wire got detached (It is a
> very low quality job of crimping). And the USB 21
> pin connector is not that great (very tight). Thes
> e parts are not something I would trust. I think y
> ou need to solder them (instead of molex).
Different strategy this time, back to ThinClient/CinnoMint, use GParted more carefully, format Ext4 and wait.
So this is seen on the LAN but you can't copy to it.
As for the lovely Molex parts, me too I changed to a different power supply, the full Molex 5 and 12 volt one you get with a hard drive-to-USB adapter. I'll come back to the cheap molex cables one of these days and make them heavy duty with Dolar Store USB cables and better crimping like you said, and careful epoxy strain relief. For now I no longer trust the ones from Singapore.
So, any quick code to make the Media > JoeyUSB3 folder read and writable? Or does that involve SAMBA yeah it probably does Lol I still have doubts this will write anything. But I'm not touching a thing for now :-)
=========
-= Cloud 9 =-
-------------------------------------------------------
> Joey,
>
> 1. If the disk is high capacity, Ext3 will take a
> long time.
> 2. It must be sdb1 (sdb is the whole disk). sdb1 i
> s the partition to be formatted.
>
>
> mkfs.ext3 -L JoeyUSB3 /dev/sdb1 >>
> Or you can try ext4. Ext4 will be very fast (it on
> ly partially formats the partition, and will slowl
> y perform a background task to complete).
>
> mkfs.ext4 -L JoeyUSB3 /dev/sdb1 >>
> -----
>
> BTW, my USB-molex black wire got detached (It is a
> very low quality job of crimping). And the USB 21
> pin connector is not that great (very tight). Thes
> e parts are not something I would trust. I think y
> ou need to solder them (instead of molex).
Different strategy this time, back to ThinClient/CinnoMint, use GParted more carefully, format Ext4 and wait.
root@DebianPlug:~# fdisk -l /dev/sdb Disk /dev/sdb: 28.7 GiB, 30752000000 bytes, 60062500 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xbbd38c62 Device Boot Start End Sectors Size Id Type /dev/sdb1 2048 60061695 60059648 28.7G 83 Linux root@DebianPlug:~# sync root@DebianPlug:~# mkdir -p /media/JoeyUSB3 root@DebianPlug:~# mount -o noatime /dev/sdb1 /media/JoeyUSB3 root@DebianPlug:~# mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,relatime,size=10240k,nr_inodes=14631,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=12092k,mode=755) /dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=24180k) tmpfs on /tmp type tmpfs (rw,relatime) rpc_pipefs on /run/rpc_pipefs type rpc_pipefs (rw,relatime) /dev/sdb1 on /media/JoeyUSB3 type ext3 (rw,noatime,data=ordered) root@DebianPlug:~#
So this is seen on the LAN but you can't copy to it.
As for the lovely Molex parts, me too I changed to a different power supply, the full Molex 5 and 12 volt one you get with a hard drive-to-USB adapter. I'll come back to the cheap molex cables one of these days and make them heavy duty with Dolar Store USB cables and better crimping like you said, and careful epoxy strain relief. For now I no longer trust the ones from Singapore.
So, any quick code to make the Media > JoeyUSB3 folder read and writable? Or does that involve SAMBA yeah it probably does Lol I still have doubts this will write anything. But I'm not touching a thing for now :-)
=========
-= Cloud 9 =-
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 19, 2017 06:26PM |
Admin Registered: 13 years ago Posts: 18,898 |
root@DebianPlug:~# mount /dev/sdb1 on /media/JoeyUSB3 type ext3 (rw,noatime,data=ordered)
This is great so far!
Now check capacity
df -h
Now just copy some files and measure the time:
cd /media/JoeyUSB3 time cp -a /boot/vmlinu* . syncchekck the files sizes
ls -lh vmlinu*
Download a large file (this is the kernel source code):
wget https://www.kernel.org/pub/linux/kernel/v4.x/linux-4.4.54.tar.xzCheck the size:
ls -lh linux-4.4.54.tar.xzExtract the kernel source code and measure the time
time tar xf linux-4.4.54.tar.xz
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/19/2017 06:28PM by bodhi.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 19, 2017 06:27PM |
Admin Registered: 13 years ago Posts: 18,898 |
SAMBA instruction will come later!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
